How to Fix a Sagging Door: Step-by-Step Guide

How to fix a sagging door: tighten the hinge screws, replace any stripped ones with longer screws that bite into the frame, shim the hinge if the door still drops, and plane the edge only as a last step. The biggest mistake is planing a door that only needed its hinges tightened.

This guide covers how to fix a sagging door step by step, the causes behind a dropped door, when a shim or longer screw is the right answer, and what a Sydney handyman charges to adjust one.

Key points

  • This is a ten-step job for most internal doors, and most sagging doors are fixed in the first three steps by tightening or replacing the hinge screws.
  • A screwdriver, a wooden wedge and a set of longer screws are the tools you cannot skip, because the problem is nearly always loose hinge fixings.
  • Support the door’s weight with a second person or wedges before you undo anything, and never plane a door until you have checked the hinges first.
  • A Sydney handyman typically charges about $185 to repair or adjust a door (range $115–$320, October 2026).

Can you fix a sagging door yourself?

Most sagging doors are an easy DIY fix. Use this table to work out how far you need to go.

Your situationDIY OK?Why
Loose hinge screws on an internal doorYesTightening or replacing screws is the usual cure and needs only a screwdriver and a few minutes.
Stripped screw holes in the frameYesFill the holes with timber dowel and glue, or use longer screws that reach the solid framing behind the jamb.
Door rubbing at the latch side or top cornerYes, with careShim or adjust the hinges first, then plane or sand only the exact spot that rubs.
Heavy solid-core or timber front doorTwo peopleThe weight is high and awkward, so have a helper hold it while you adjust hinges.
Cracked, split or swollen door or frameCall a handymanRepairs to the structure or to a swollen door on an old sandstone footing often need a carpenter’s eye.
Fire-rated, glass or aluminium sliding doorCheck firstFollow the manufacturer’s instructions and see our sliding door guide for tracks and rollers.
Garage door or roller door springsNoTensioned springs store dangerous energy, so book a garage door technician.

Tools and materials to fix a sagging door

ItemWhat it’s forTip
Screwdriver or drill driverTightens and replaces hinge screwsUse a hand screwdriver for the final turn so you do not strip the hole again.
Longer wood screwsReach the solid frame behind the jambMatch the head size to the hinge, and check the packet for the right screw type for your timber.
Wooden wedges or off-cutsHold the door in place while you workSlide two under the door so it does not drop when you unscrew a hinge.
Cardboard or hinge shimsPacks out a hinge to lift the door edgeCut thin strips from a cereal box to fit behind the hinge leaf, and add one layer at a time.
Timber dowel and wood glueRepairs stripped holesCut the dowel to length, glue it in, let it set, then drill a pilot hole before the screw.
Spirit level and pencilChecks the gaps and marks any rub pointLook for an even gap around the door, and mark the rubbing spot with pencil before you plane.
Block plane or sanding blockTrims the edge as a last resortTake off a little at a time and seal any bare timber afterwards.

How to fix a sagging door: step by step

Allow a helper for a heavy door, and keep your fingers clear of the hinge side when the door shifts.

  1. Open the door and look at the gaps, noting where it rubs, which hinge looks loose, and whether the latch still lines up with the strike plate.
  2. Wedge the door from underneath on the latch side so its weight sits on the wedges and not on the hinges.
  3. Tighten every screw on each hinge, starting with the top hinge, because that one carries most of the pull on a sagging door.
  4. Check each screw as you turn it, and note any that spin without gripping, because the hole is stripped and needs a repair.
  5. Fix stripped holes by gluing in dowel or matchsticks, trimming them flush, and drilling a small pilot hole through them before you refit the screw.
  6. Or swap the screw for a longer one that passes through the jamb and bites into the framing behind it; check it is not so long it breaks through.
  7. If the door still rubs near the latch, remove the top hinge and pack a thin cardboard shim behind its leaf to pivot the door up.
  8. Close the door and check the gap along the top and sides again, adding or removing one layer of shim until the gaps look even.
  9. Plane or sand the rubbing edge only if the gap is still tight after the hinge adjustments, and take off small amounts at a time.
  10. Seal any bare timber with paint or sealer, then open and close the door several times to check it swings freely and latches properly.

Why a door sags and what to check

Knowing the cause stops the door dropping again, and settling footings under older sandstone homes are a common reason.

  • Check for loose or stripped hinge screws first, since years of slamming and weight stretch the holes until the screws no longer grip.
  • Look at the top hinge and the frame beside it for a gap or crack, which suggests the jamb has pulled away from the stud.
  • Check that the door is still square by measuring its diagonals, because a twisted or swollen door will rub no matter how you adjust the hinges.
  • Look at the floor and frame for movement, as a settling footing or a sinking floor can pull the frame out of square.
  • Check for moisture at the bottom of the door, where damp timber swells and sags, and repaint the bottom edge once you fix it.
  • Check that the hinges are the right size and number for the door’s weight, and add a third hinge on a heavy door if the manufacturer allows.

Common mistakes when you fix a sagging door

  • Planing the door before you tighten the hinges, which removes timber you cannot put back and leaves a gap once the door is fixed.
  • Using short or wrong screws that spin in the same worn holes instead of reaching the solid framing behind the jamb.
  • Skipping the wedges and letting the door’s weight hang on one hinge while you undo the other.
  • Overtightening screws until the hinge leaf pulls out of its recess or the screw head snaps.
  • Drilling into old sheeting or fibro next to the frame in a pre-1990 home without checking for asbestos first.
  • Lifting a heavy door alone, which risks a dropped door, damaged frame and a strained back.

When to call a handyman (or a licensed trade)

  • The frame is cracked, split or pulled away from the wall, and the hinge screws have nothing solid to grip.
  • The door is heavy, glazed or fire-rated, and you want it hung and adjusted safely with a second pair of hands.
  • The door still rubs after the hinges are tightened and shimmed, and you are not sure where to plane.
  • The lock, latch or deadbolt no longer lines up, and you need a licensed locksmith such as TQN Locksmith for the lock itself.
  • The door is a garage or roller door with tensioned springs, which need a garage door technician.
  • You are renting and want the repair done neatly with a record of the work for your landlord.

Cost to hire a handyman to fix a sagging door in Sydney

Prices include GST and come from October 2026 Sydney data. For other door jobs, our door handle replacement guide covers the hardware side.

JobLowTypicalHigh
Door repair or adjustment, Sydney (per job)$115$185$320
Handyman hourly rate, Sydney$57$105$140
Call-out or minimum charge, Sydney$92$140$170
Half-day handyman, Sydney (4 hours)$230$415$645
  • Ask for several door jobs to be done in one visit, such as a squeaky door or a loose door knob.
  • Send photos of the door and the gap so the handyman can bring shims, longer screws and a plane.
  • Check the door sizes in our standard door sizes guide before you ask for a replacement quote.

FAQ: how to fix a sagging door

How to fix a sagging door?

Wedge the door, then tighten every hinge screw, starting with the top hinge. Replace stripped screws with longer ones that reach the framing, or fill the holes with dowel and glue. If the door still rubs, pack the hinge with a thin shim and plane only the rubbing spot as a last step.

Why does my door keep dropping after I tighten the screws?

The screw holes are probably stripped, or the screws are not reaching solid framing. Fill the holes with dowel and glue, or fit longer screws that pass through the jamb. If it still drops, the frame may have moved and a handyman should check it.

Can you fix a sagging door without taking it off?

Yes. Wedge the door in place, then tighten or replace screws one hinge at a time. You only need to remove the door if you must plane an edge, repair a hinge recess or fill stripped holes, and a helper makes that much easier.

Should you plane a sagging door?

Plane only when hinge fixes do not clear the rub. Mark the exact spot, take off small amounts and test often, then seal the bare timber. Planing first removes wood you cannot restore, and the door may rub again when the hinges are tightened.

Getting your door fixed in Sydney

If you would rather not wrestle a heavy door, we can tighten, shim and adjust it in one visit and fix any related squeaks or sticking latches. Book a Sydney handyman and add other door and hardware jobs. For related fixes, start with the door handle replacement guide.