Composite decking price in Australia typically runs about $280–$720 per m² installed, depending on board grade and how much framing the deck needs (indicative — get itemised quotes). The biggest swing is between budget uncapped boards and premium capped boards, followed by whether you reuse an existing frame. This guide covers the composite decking price by type and city, what changes the total, DIY versus hiring, and a quote checklist. If you are still choosing a design, start with our how to build a deck guide.
Key points
- Expect roughly $280–$720 per m² installed for composite, with boards alone from about $60 to $320 per m² (indicative — get itemised quotes).
- The biggest cost driver is board grade: capped, wide-profile boards with hidden clips cost far more than hollow uncapped ones.
- The cheapest route is laying composite over a sound existing frame, which skips new footings and bearers.
- DIY suits a small deck on a flat frame; anything valued over $5,000 must be built by a builder licensed by Building Commission NSW.
Composite decking price: price table
Prices are per square metre and assume standard access on a typical suburban block.
| Type | Boards per m² | Framing and labour per m² | Installed per m² |
|---|---|---|---|
| Hollow, uncapped WPC (budget) | $60–$110 (indicative) | $220–$350 (indicative) | $280–$460 (indicative) |
| Solid, uncapped composite | $90–$150 (indicative) | $220–$350 (indicative) | $310–$500 (indicative) |
| Capped composite (mid-range) | $130–$220 (indicative) | $230–$360 (indicative) | $360–$580 (indicative) |
| Premium capped, wide boards, hidden clips | $200–$320 (indicative) | $250–$400 (indicative) | $450–$720 (indicative) |
| Re-decking onto a sound existing frame | $130–$320 (indicative) | $90–$180 (indicative) | $220–$500 (indicative) |
| Composite tiles over an existing slab | $90–$200 (indicative) | $50–$120 (indicative) | $140–$320 (indicative) |
- Treat these as planning bands: board brand, colour range and your supplier’s current price list will shift any row.
- Stairs, edging, fascia boards and lighting are usually priced as extras, so ask for them as separate lines.
- Check the manufacturer’s installation guide for joist spacing, board gaps and fixings rather than relying on a quote’s assumptions.
Composite decking price per m2 in Australia, by city
Only handyman labour rates for Sydney and Melbourne are verified, so use them as a guide to local labour and collect quotes for everywhere else.
| City | Handyman hourly rate | Call-out or minimum | Composite decking guidance |
|---|---|---|---|
| Sydney | $57–$140 (typical $105) | $92–$170 (typical $140) | Use the table above; sloping blocks and tight access raise the framing cost. |
| Melbourne | $52–$125 (typical $94) | $84–$160 (typical $125) | Labour rates run slightly lower, but board prices are set nationally by suppliers. |
| Brisbane | No verified rate held | No verified rate held | Heat and UV matter more here, so ask about board surface temperature and warranty terms. |
| Perth | No verified rate held | No verified rate held | Get three itemised local quotes and compare the board brand line by line. |
| Adelaide | No verified rate held | No verified rate held | Get three itemised local quotes and compare the board brand line by line. |
WPC decking price: what you are paying for
The same terms appear on every supplier’s website, and they explain most of the price gap between boards.
| Term | Meaning | Why it matters |
|---|---|---|
| WPC (composite wood decking) | Boards made from wood fibre and plastic | Resists rot and splinters, but weight, heat and colour vary by brand. |
| Capped | A protective outer shell over the core | Usually resists stains and fading better than uncapped boards, at a higher price. |
| Hollow board | Channels run through the board | Lighter and cheaper, but edges and ends need trims to hide the openings. |
| Solid board | No internal voids | Heavier and stiffer, and often handles bearer spacing better; check the packet. |
| Hidden clips | Fixings sit in grooves in the board edge | Cleaner surface, but clip and groove systems are brand-specific. |
| Bushfire rating | Whether the board suits a bushfire-prone site | Ask for the supplier’s evidence for your site; do not assume every board qualifies. |
What affects the composite decking price
Six items decide where your quote sits within a band.
- Board grade: moving from hollow uncapped to premium capped boards can nearly double the board cost per m² (indicative — get itemised quotes).
- Frame condition: a sound existing frame saves new footings and bearers, while a rotten one needs full replacement before any composite goes down.
- Height and slope: a deck with the floor more than 1 m above ground falls outside exempt development limits and needs more framing and bracing.
- Access and site: sloping Sydney blocks, narrow side access and no space to cut boards all add labour hours.
- Extras: stairs, balustrades, fascia, lighting and privacy screens are separate lines that can add up quickly.
- Older homes: if the deck attaches to a pre-1990 wall or eave, identify suspect asbestos-containing material before anyone drills or cuts.
DIY vs hiring a pro for composite decking
Laying boards onto a sound, level frame is learnable; building the frame itself is where mistakes get expensive.
| DIY or a handyman | Book a licensed builder or trade |
|---|---|
| Replace boards on an existing frame using the maker’s clip system | New deck or any building work valued at more than $5,000: licensed by Building Commission NSW |
| Check planning limits on the NSW Planning Portal, then ask your council | A deck above 25 m² or higher than 1 m above ground, which falls outside the exempt limits |
| Clean, seal edges and trim hollow board ends neatly | Structural footings, bearers and ledger fixing to the house |
| Fit a skirting or fascia strip to hide the sub-frame | Power for outdoor lights: book a licensed electrician |
| Assemble flat-pack outdoor furniture afterwards | Plumbing for outdoor taps or showers: book a licensed plumber |
| Measure carefully and order boards with the cut and waste allowance the supplier recommends | Anything involving drilling into suspect pre-1990 sheeting or eaves |
How to save on composite decking price without cutting corners
- Reuse a sound frame where the timber is solid and level, because new footings and bearers are a large share of the deck total.
- Choose a mid-range capped board instead of the top grade if your deck is shaded, since extra surface features add little there.
- Order from one batch, with the extra cut-off allowance the supplier recommends, so colours match and you avoid a second delivery.
- Bundle small tasks into one handyman visit: a Sydney half-day (4 hours) costs $230–$645 (typical $415) against a call-out of $92–$170.
- Keep the deck within exempt development limits where possible, which can avoid approval costs; confirm with your council or the NSW Planning Portal.
- Pay no more than the 10% maximum deposit, and make sure work under $20,000 has a written small jobs contract.
What a fair composite decking quote should include
- Itemised materials: board brand, grade and colour, clip system, joists, bearers and fixings, with quantities per m².
- The frame scope: whether existing framing is reused, repaired or replaced, and who confirms it is sound.
- Access, scaffold or hoisting needs, and a line for removal of old decking and waste.
- Council or certifier fees if the deck is not exempt, plus any engineer’s drawings required.
- The builder’s licence number, which you can check with Building Commission NSW, and the Home Building Compensation cover if the job exceeds $20,000.
- Workmanship warranty in writing, kept separate from the board manufacturer’s warranty terms, which you should read in full.
FAQ: composite decking price
What is the composite decking price in Australia?
Installed composite decking commonly costs about $280–$720 per m², depending on board grade and framing (indicative — get itemised quotes). Boards alone range far lower. Always ask whether a quote covers the frame, stairs, edging and removal of old decking.
What is composite decking price per m2 in Australia?
Boards alone are roughly $60–$320 per m² depending on whether they are hollow, solid, uncapped or capped (indicative — get itemised quotes). Add framing and labour for the installed figure, and check the manufacturer’s coverage rate per board so you order the right quantity.
Is WPC decking price higher than timber?
Often yes upfront, because composite boards cost more than treated pine or many hardwoods (indicative — get itemised quotes). The trade-off is less sanding and oiling over time. Compare the full lifetime cost, including cleaning and any warranty conditions, instead of the board price alone.
Does composite wood decking price include installation?
Not unless the quote says so. Supplier prices are usually per board or per m², and labour, framing, fixings and trims are separate lines. Ask for an itemised written quote so you can see exactly what is included.
Can I install composite decking myself?
You can lay boards on a sound frame if you follow the manufacturer’s instructions. A new deck valued over $5,000 must be built by someone licensed by Building Commission NSW, and structural work has to meet council or certifier requirements.
Getting composite decking priced in Sydney
If you want a straight answer on your frame and a written quote, we can inspect the deck, replace boards and handle the finishing work. Book a Sydney handyman for deck repairs and small decking jobs, and see our concrete driveway cost and retaining wall cost guides if the project includes hard landscaping, plus building a retaining wall, fence and gate repair, laying pavers and a raised garden bed.


