Exposed Aggregate Concrete Cost in Sydney (2026 Guide)

Exposed aggregate concrete cost for a driveway usually sits around $130 to $230 per m² installed, a step above plain broom-finish concrete (indicative — get itemised quotes). Slab thickness, access, reinforcement, drainage and the aggregate you choose drive most of the difference between quotes.

This guide covers exposed aggregate concrete cost, what a plain concrete driveway costs, resurfacing, colour seal and sealing prices, DIY limits, and what a fair quote includes. Driveways often sit alongside other outdoor jobs, such as those in our deck building guide.

Key points

  • Exposed aggregate concrete cost is higher than a broom finish because of the aggregate, the surface retarder and the washing-off stage.
  • The cheapest route is a plain broom-finish slab, while the cheapest repair is resurfacing or colour sealing an existing sound slab.
  • A driveway pour is rarely DIY; a full driveway usually passes $5,000, so building work must be done by someone licensed by Building Commission NSW.
  • A Sydney handyman typically charges $105 an hour (range $57–$140, October 2026), and suits cleaning, sealing and small crack jobs.

Exposed aggregate concrete cost: price table by finish

These installed ranges per square metre assume a standard residential driveway on a prepared base; every figure is a guide, not a quote.

FinishInstalled price per m²Notes
Plain broom-finish concrete$100–$170 (indicative — get itemised quotes)Cheapest new driveway; good grip, plain look.
Exposed aggregate concrete$130–$230 (indicative — get itemised quotes)Natural stones show through the surface; very durable when sealed.
Coloured concrete$140–$240 (indicative — get itemised quotes)Oxide mixed through the slab, plus sealing.
Stamped or patterned concrete$150–$280 (indicative — get itemised quotes)Highest labour cost; needs careful sealing and maintenance.
Pavers over a compacted base$120–$250 (indicative — get itemised quotes)See our how to lay pavers guide for the alternative.

Concrete driveway cost per m2 and concrete driveway price by size

Most homeowners ask how much a concrete driveway costs overall, so here is a rough guide by size.

Driveway sizePlain concrete totalExposed aggregate total
Single car, about 20 m² (indicative)$2,000–$3,400 (indicative — get itemised quotes)$2,600–$4,600 (indicative — get itemised quotes)
Double car, about 40 m² (indicative)$4,000–$6,800 (indicative — get itemised quotes)$5,200–$9,200 (indicative — get itemised quotes)
Long battleaxe drive, about 60 m² (indicative)$6,000–$10,200 (indicative — get itemised quotes)$7,800–$13,800 (indicative — get itemised quotes)
Add-on: removing an old slabQuoted separately (indicative — get itemised quotes)Quoted separately (indicative — get itemised quotes)
Add-on: crossover or council worksCheck with your council (indicative — get itemised quotes)Check with your council (indicative — get itemised quotes)

Exposed aggregate concrete cost by city

Labour, delivery distance and site access change the price, so treat these ranges as a comparison, with Sydney first.

CityExposed aggregate, per m²Concrete driveway, per m²
Sydney$140–$230 (indicative — get itemised quotes)$110–$180 (indicative — get itemised quotes)
Melbourne$130–$220 (indicative — get itemised quotes)$100–$170 (indicative — get itemised quotes)
Brisbane$125–$215 (indicative — get itemised quotes)$95–$165 (indicative — get itemised quotes)
Perth$125–$215 (indicative — get itemised quotes)$95–$165 (indicative — get itemised quotes)
Adelaide$120–$205 (indicative — get itemised quotes)$90–$160 (indicative — get itemised quotes)

What affects exposed aggregate concrete cost

  • Base and excavation: removing old concrete, soil or roots takes machine time, and tip fees add to the price.
  • Thickness and reinforcement: a heavier slab for cars and trucks uses more concrete and mesh than a path.
  • Aggregate choice: local river stones, quartz or coloured pebbles cost more than the standard mix.
  • Access and pumping: if the truck can’t reach, the concreter will barrow or hire a pump.
  • Drainage and falls: a driveway sloping toward the house needs drains, and stormwater work may need a licensed plumber.
  • Council rules: crossovers, kerb works and stormwater connections may need council approval; confirm before you book.
  • Sealing and colour: a good sealer protects the stones, and colour sealing adds to the final total.

Concrete driveway resurfacing, colour seal and sealing cost

If your slab is structurally sound but tired, cleaning and resurfacing can cost much less than a new driveway.

OptionTypical cost per m²When it suits
Pressure wash and reseal$10–$35 (indicative — get itemised quotes)Faded but sound exposed aggregate or plain concrete
Concrete sealer, supply and apply$15–$45 (indicative — get itemised quotes)Protects against oil, stains and moisture; follow the label for recoat times
Colour seal concrete$25–$60 (indicative — get itemised quotes)Hides patchy stains and refreshes the colour
Water-based concrete stain$20–$55 (indicative — get itemised quotes)Subtle colour change on clean concrete; test a patch first
Concrete driveway resurfacing$50–$120 (indicative — get itemised quotes)Surface wear or light spalling, but not a failing base

DIY concrete vs hiring a pro

TaskDIYHire a pro
Pouring a full drivewayNot realistic; timing, falls and finishing are unforgivingLicensed builder or experienced concreter
Exposed aggregate finishVery hard; the surface must be washed at exactly the right timeSpecialist concreter
Cleaning and sealingYes, if you follow the sealer label and test a patchHandyman for large areas or awkward access
Small cracksUsually fine with a repair productHandyman; see our fence and gate repair guide for related jobs
Pouring a post footingYes, with bagged concrete and clear instructionsHandyman or fencer
Any job above $5,000Needs a licensed builderVerify the licence with Building Commission NSW

How to pressure wash and concrete a post

These are the two driveway-adjacent jobs most homeowners tackle themselves, so here is the safe way to do each.

  • Sweep first, then pressure wash in even, overlapping passes from a consistent distance to avoid etching the surface or exposing stones.
  • Test a hidden corner before washing exposed aggregate, because aggressive pressure can loosen stones near edges and joints.
  • Let the driveway dry before sealing, and choose a day without rain, as the sealer label will specify.
  • To concrete a post, dig the hole to the depth the fence or post instructions state, and keep it plumb with a level and braces.
  • Fill with premixed concrete as the bag directs, and slope the top away from the post so water drains away.
  • Leave braces in place until the concrete has cured per the label; Colorbond fences belong to a licensed construction team, and our fence building guide covers timber options.

Common mistakes with concrete driveways

  • Choosing the cheapest quote without comparing thickness, reinforcement and base preparation between quotes.
  • Skipping control joints, which leaves the slab free to crack in random places.
  • Sealing before the slab has cured, or sealing damp concrete so the sealer turns cloudy.
  • Washing exposed aggregate at too high a pressure, which strips stones from the surface.
  • Ignoring council rules for crossovers and stormwater, then being forced to redo the edge.
  • Breaking up an old slab in a pre-1990 home without checking for asbestos in nearby fibro or sheeting.

What a fair concrete driveway quote should include

  • Itemised area, thickness, strength grade, reinforcement, finish and sealer, so you can compare exposed aggregate concrete cost between quotes.
  • Excavation, base, formwork, drainage, waste removal and cleaning down.
  • Council approvals and crossover works, or a clear statement that they are excluded.
  • A written contract: work under $20,000 uses a small jobs contract, over $20,000 needs a full home building contract plus Home Building Compensation cover, and the maximum deposit is 10%.
  • The contractor’s licence number, insurance and workmanship warranty in writing.
  • Curing and sealing advice, including how long before cars can drive on the new surface.

FAQ: concrete driveway and exposed aggregate cost

How much does a concrete driveway cost?

A plain broom-finish concrete driveway often costs about $100 to $170 per m² installed (indicative — get itemised quotes). A double-car driveway therefore lands in the thousands. Ask each concreter for an itemised quote that covers excavation, base, reinforcement and removal.

How much does an aggregate driveway cost?

Exposed aggregate typically costs more than plain concrete, at about $130 to $230 per m² installed (indicative — get itemised quotes). The aggregate, labour for the wash-off and the sealer all add to the price compared with a broom finish.

How much does exposed aggregate concrete cost to reseal?

Pressure washing and sealing generally cost far less than a new driveway, often $15 to $45 per m² (indicative — get itemised quotes). Check the sealer label for recoat intervals, and test a patch first on exposed aggregate.

Is DIY concrete a good idea for a driveway?

No for a full driveway, because timing, falls, joints and finishing are unforgiving. DIY concrete suits small jobs such as post footings, steps or crack repairs, using bagged mix and following the label instructions.

Getting concrete work done in Sydney

If you’d rather not scrub, seal or repair your driveway yourself, we can pressure wash, patch cracks and reseal in one visit, and refer full pours to licensed builders. Book a Sydney handyman and bundle other outdoor jobs, such as those in our retaining wall cost and retaining wall building guides, into the same visit.