Replacing kitchen cabinet doors only is the cheapest way to refresh a sound kitchen, because you keep the boxes, benchtop and plumbing and swap just the fronts and hinges. A Sydney handyman typically charges $105 an hour (range $57–$140, October 2026), and the main risk is measuring wrongly, which leaves doors that rub or gap.
This guide covers measuring, made-to-measure options, step-by-step fitting, cheaper ways to update old kitchen cabinets without replacing them, and what a handyman charges. Start with the hardware and our door handle replacement guide if your handles are the real eyesore.
Key points
- Replacing kitchen cabinet doors only works when the carcasses are solid, dry and square; swollen or crumbling boxes are a sign to replace more.
- Measure each opening and the existing hinge type, because made-to-measure doors are non-returnable once cut.
- Painting or wrapping old doors is cheaper than new ones, but spray finishing is best left to a licensed painter.
- A Sydney door repair or adjustment job typically costs $185 (range $115–$320), and a handyman call-out typically costs $140 (range $92–$170).
Replacing kitchen cabinet doors only: when it makes sense
Match the option to the condition of the cabinets, not just the budget, as most Sydney kitchens from the last few decades have usable boxes behind tired fronts.
| Option | Best when | Watch out for |
|---|---|---|
| New doors, same carcasses | Boxes are solid and the layout works | Door sizes must match the existing openings and hinge positions |
| Repaint existing doors | Doors are sound but dated | Poor prep causes peeling around handles and edges |
| Wrap or film the doors | Flat panel doors in good condition | Heat near ovens and cooktops can lift the edges |
| Replace carcasses and doors | Water damage, swelling or a layout change | Much higher cost, and plumbing and electrical need licensed trades |
- Check inside the cabinet under the sink for swelling, soft chipboard or mould before you spend anything on new fronts.
- Open and close every door to test the hinges, since sagging often comes from worn hinge plates rather than the door itself.
- Look at the kickboards and drawer runners, because tired hardware is easier to fix while the doors are off.
Cabinet door replacement: how to measure for a made-to-measure order
Accurate measuring decides whether the new doors sit flush, so take your time and write everything down.
- Remove one door from each size group and measure the existing height and width with a steel tape, noting any slight differences between doors.
- Measure the cabinet opening from inside the frame or edge to edge, depending on whether the doors are inset, half overlay or full overlay.
- Identify the hinge type, such as a cup hinge or a surface-mounted hinge, and check whether the plates are screwed to the side of the box.
- Photograph the hinge position and note its distance from the top and bottom edge, because the manufacturer needs this to drill the cups.
- Mark each door’s location with masking tape and a number so you can match the replacement to the right opening.
- Ask the supplier to confirm the grain direction, edge finish and whether pre-drilled hinge holes are included.
Cupboard doors made to measure: options and prices
Cupboard doors made to measure come from kitchen door suppliers and some Bunnings and IKEA ranges, and prices vary widely by material and finish, so treat the figures below as indicative.
| Door type | Price per door (indicative) | Notes |
|---|---|---|
| Flat-pack standard sizes | $30–$90 (indicative) | Cheapest, but limited sizes and colours |
| Vinyl-wrapped MDF | $60–$160 (indicative) | Common, moisture sensitive if the edge is damaged |
| Polyurethane painted | $150–$350 (indicative) | Smooth finish, higher cost, made to order |
| Solid timber or veneer | $200–$500 (indicative) | Long lead times and finishing needed |
- Request a written quote that lists each door size, the finish and the hinge drilling.
- Order hinges at the same time, and confirm the brand and soft-close option, such as Blum.
How to replace kitchen cupboard doors: step by step
Once the new doors arrive, the fitting itself is usually a half-day job for one person who is comfortable with a drill.
- Empty the cupboard, support the door with one hand and unscrew the hinge arms from the door, keeping the screws in a labelled bag.
- Leave the mounting plates on the box if the new hinges match, or unscrew them and fill any spare holes with timber filler.
- Clip or screw the new hinges into the pre-drilled cups on each door, checking the hinge faces the right way before tightening.
- Offer the door up to the box, clip or screw the hinge arms to the mounting plates and hold the door while you check alignment.
- Adjust the hinge screws for depth, height and side-to-side, aiming for an even gap around each door and a flush front across the run.
- Fit handles or knobs last, using a template so the holes line up from door to door.
- Close each door several times and re-adjust any that catch, then check soft-close hinges move smoothly.
- Wipe the doors clean and remove protective film once all the fitting is done.
Kitchen cabinets DIY: how to update old kitchen cabinets without replacing them
If the doors are solid, a good clean, minor repair and new hardware can lift a tired kitchen for far less than new fronts.
- Degrease and sand the doors lightly, then use a bonding primer and a cabinet-grade paint for a durable finish.
- Replace worn hinges and handles first, because sagging doors and loose handles make a kitchen look older than the paint does.
- Swap flat doors for a shaker-style kit only where the carcasses are square and the openings are standard.
- Re-edge chipped laminate and patch small holes before you paint, using products suited to your door material.
- Check any fibro or old wall lining behind the splashback for asbestos before you sand, drill or cut near it.
- Book a licensed painter for spray finishing, and see our squeaky door guide for hinge lubrication tips.
Replacing kitchen doors in a rental or strata unit
In NSW, a landlord cannot unreasonably refuse certain minor changes, but replacing kitchen fronts is not on that list, so ask in writing first.
- Get written consent before you remove or replace any door, since kitchen fixtures belong to the owner.
- Keep the originals and refit them when you leave if the lease requires the kitchen to be returned as found.
- Choose clip-on or removable hardware where possible, so you do not drill fresh holes in the carcasses.
- Strata lots may have rules about visible changes, so check your by-laws and ask the committee if the kitchen faces common property.
- Do not touch taps, wiring or gas lines while you work; use a licensed electrician or plumber for those.
- Photograph the kitchen before and after for your records.
Common mistakes when replacing kitchen cabinet doors only
- Ordering doors before checking the hinge type and positions, which leaves cups that do not line up with the old plates.
- Skipping a measure of every door, even though cabinets installed by different trades often differ slightly.
- Over-tightening hinge screws into chipboard, which strips the hole and makes the door sag again in months.
- Painting over greasy or glossy doors without sanding and priming, so the finish peels near the stove.
- Drilling or sanding old fibro or wall lining without checking for asbestos in a home built before 1990.
- Keeping the same hardware after replacing the fronts, when new hinges and handles can transform the result.
Cost to hire a handyman to replace kitchen cupboard doors in Sydney
A handyman will fit supplied doors and hinges and adjust the finish, but does not supply the doors themselves.
| Job | Low | Typical | High |
|---|---|---|---|
| Handyman hourly rate, Sydney | $57 | $105 | $140 |
| Call-out or minimum charge, Sydney | $92 | $140 | $170 |
| Half-day handyman, Sydney (4 hours) | $230 | $415 | $645 |
| Full-day handyman, Sydney (8 hours) | $435 | $690 | $1025 |
| Door repair or adjustment | $115 | $185 | $320 |
- A full day can cost less than eight hours billed hourly, so a whole kitchen of doors often suits a day booking.
- If the kitchen renovation grows beyond $5,000 in value, the work must be done by someone licensed by Building Commission NSW.
FAQ: replacing kitchen cabinet doors only
How to update old kitchen cabinets without replacing them?
Clean, sand and prime the doors, then repaint with a cabinet-grade paint and fit new hinges and handles. Repair chipped edges first and check the carcasses are dry and solid. A licensed painter can spray the finish if you want a factory look.
Is replacing kitchen cabinet doors only cheaper than a full renovation?
Yes, usually by a wide margin, because you keep the carcasses, benchtop and plumbing. The saving disappears if the boxes are swollen or the layout needs to change, so inspect the inside of the cabinets before you order anything.
Can a handyman fit made-to-measure cupboard doors?
Yes. A handyman can fit supplied doors, swap hinges and adjust the gaps. Electrical, plumbing and gas changes need a licensed trade, and building work valued at more than $5,000 must be done by someone licensed by Building Commission NSW.
How long does it take to replace kitchen cupboard doors?
Fitting usually takes a few hours for an average kitchen once the doors arrive. Allow extra time for ordering, because made-to-measure doors can take weeks, and book a handyman for a half or full day to keep the call-out cost down.
Getting kitchen cabinet doors replaced in Sydney
If you would rather not measure, order and adjust every hinge, we can fit your doors and flag anything that needs a licensed trade. Book a Sydney handyman for replacing kitchen cabinet doors only, and see our guides on loose door knobs, standard door sizes, shower screen seals, garage door seals and garage door remotes for other door jobs around the house.


