How to Hang Festoon Lights: Step-by-Step Guide

How to hang festoon lights: plan the route, fix solid hooks or eye bolts to sound timber or masonry, run a support wire between them, then clip the lights along the wire and plug them into a safe outdoor power point. The biggest mistake is hanging the lights straight from the cable, which stretches the wiring and pulls fixings out of the wall.

This guide covers how to hang festoon lights step by step, how to hang fairy lights indoors, and what a Sydney handyman charges for the job.

Key points

  • This is a nine-step job that suits confident DIYers, and the support wire does the work so the light cable never carries the load.
  • A stable ladder and a second person are the tools you cannot skip, because most festoon lights go above shoulder height.
  • Check fascias and eaves for asbestos in pre-1990 homes before you drill, and use a licensed electrician for any new or moved power point.
  • A Sydney handyman typically charges about $125 for a small hanging job (range $80–$205, October 2026), with a call-out of about $140.

Can you hang festoon lights yourself?

Most people can hang lights between two solid fixing points. Check this table to see where your project sits.

Your situationDIY OK?Why
Plug-in lights between a house wall and a postYesYou need solid fixings at each end, a support wire and a safe outdoor power point.
Fixing into timber fascia or a pergola beamYes, with careSound timber holds eye hooks well, but you need a ladder and a second person at height.
Brick or masonry wallYes, with a hammer drillMasonry anchors hold well; see our guide to drilling into brick for the method.
Pre-1990 home with fibro eaves or sheetingCheck firstHomes built or renovated before 1990 are likely to contain asbestos, so check asbestos.nsw.gov.au before you drill.
No outdoor power point nearbyNoAdding or moving a power point is electrical work that needs a licensed electrician in NSW.
Hardwired lights or a new circuitNoHardwiring lights is licensed electrical work, so book a licensed electrician.
Rental propertyAsk firstGet written consent before you drill, or use clip-on options that do not mark the walls.

Tools and materials to hang festoon lights

ItemWhat it’s forTip
Outdoor-rated festoon lightsProvide the lightingCheck the packet or label for outdoor use and the maximum number of connected strings.
Support wire or catenary cableCarries the weight so the lights do notChoose a stainless steel wire made for outdoor use and check the maker’s load guidance.
Eye hooks, eye bolts or bracketsAnchor the wire at each endMatch the fixing to the wall or beam, and check the packet rating rather than guessing.
Turnbuckle or tensionerTightens the wirePull the wire taut, but leave a gentle sag in the lights so they do not strain.
Cable clips or tiesAttach the light string to the wireUse outdoor-rated UV-resistant ties and avoid tight clamps that squeeze the cable.
Stable ladderReaches the fixing pointsSet it on firm, level ground and keep three points of contact when you climb.
Drill, bits and levelMakes pilot holes and sets the run straightUse a wood bit for timber and a masonry bit in hammer mode for brick.

How to hang festoon lights: step by step

Work with a second person at the base of the ladder, and never hang lights in wet or windy weather.

  1. Sketch the route on paper, measure each span, and choose fixing points that are solid timber, steel or masonry rather than gutters or fibro.
  2. Check the power source, and plan the route so the plug sits near an existing outdoor power point, with no cable stretched across a walkway.
  3. Scan the wall for cables and pipes if you will drill, and check pre-1990 eaves and sheeting for asbestos before you start.
  4. Mark the fixing points with pencil, using a level so the support wire will run straight, and check the ladder reach.
  5. Drill pilot holes at each point, then fix the eye hooks or bolts, with masonry anchors in brick as the packet directs.
  6. Thread the support wire through the end fixings and tension it with a turnbuckle until it is taut and level.
  7. Lay the lights along the wire from the power end, clipping them at regular intervals and leaving a gentle drape between clips.
  8. Run any spare cable away from foot traffic, keep the plug and connections off the ground and sheltered from rain.
  9. Switch on after dark to check every bulb works, then recheck the fixings and wire tension after the first week.

How to hang festoon lights on a pergola, fence or house wall

Each surface asks for a different fixing, so match the method to where your lights will sit.

  • On a timber pergola, screw eye hooks into the beam or post centre, and avoid cracked or rotten timber that will not hold.
  • On a fence post, use a hook or a ring bolt through the post, and avoid light sheeting or palings that cannot hold the tension.
  • On a brick wall, drill masonry holes and fit anchors made for brick, cleaning out the dust before fitting.
  • On a house with eaves, check the material first, because fibro eaves in pre-1990 homes may contain asbestos.
  • On a freestanding pole, set the pole in concrete or a rated base, and add guy wires if it leans under the tension.
  • Keep decks, pergolas and fences within council rules; our deck building guide notes when approval is needed.

How to hang fairy lights indoors

Fairy lights are lighter and low-voltage, so you can usually avoid drilling and protect rental walls.

  • Use adhesive hooks or clips rated for the weight of the string, and check the packet before you stick them to paint.
  • Hang lights along a picture rail, curtain rod or shelf edge, where they sit without any new holes in the wall.
  • Keep the lights away from curtains, paper and heaters, and switch them off when you leave the room or go to bed.
  • Check the wire and plug for damage, and replace the string if the insulation is cracked or the plug is loose.
  • Use a power board with a built-in safety switch, and do not overload it with several strings.
  • In a rental, ask your landlord first; our guide to hanging things in a rental covers consent and bond.

Common mistakes when you hang festoon lights

  • Hanging the lights directly from the light cable instead of a support wire, which stretches the cable and tears fixings out.
  • Using a plasterboard-style fixing or a short screw in thin timber, when the packet says it needs solid timber or masonry.
  • Skipping the cable and pipe scan, then drilling into hidden wiring above a power point or a pipe behind the wall.
  • Pulling the wire too tight or leaving it so loose that wind and weight snap the fixings.
  • Drilling into pre-1990 fibro eaves or sheeting without checking for asbestos first.
  • Working at height alone, when a second person should hold the ladder and pass tools.

When to call a handyman (or a licensed trade)

  • The run is long, high or over a driveway, and you want the support wire fixed and tensioned safely.
  • You are fixing into brick, rendered walls or a pre-1990 home where asbestos is possible.
  • You need an outdoor power point added or moved, which needs a licensed electrician such as TQN Electrician.
  • You want the lights hardwired or on a switch, which is also licensed electrical work.
  • The structure is a deck, pergola or fence that looks weak, and a handyman should check it will hold the load.
  • You are renting and want the fixings installed neatly and removed without damage.

Cost to hire a handyman to hang festoon lights in Sydney

Prices include GST and come from October 2026 Sydney data. Festoon lights themselves are extra, so ask for fixings and wire to be itemised.

JobLowTypicalHigh
Small hanging job, Sydney (per visit)$80$125$205
Handyman hourly rate, Sydney$57$105$140
Call-out or minimum charge, Sydney$92$140$170
Half-day handyman, Sydney (4 hours)$230$415$645
  • The per-visit figure is for a comparable small fixing job, so a long run over a large yard may cost more.
  • Bundle jobs into one visit, such as hanging a heavy mirror or hanging pictures.
  • A full day can cost less than eight hourly-billed hours, so ask for a day rate if you have several jobs.

FAQ: how to hang festoon lights

How to hang festoon lights?

Fix solid hooks or eye bolts at each end, run a tensioned support wire between them, and clip the light string along the wire. Plug into a safe outdoor power point, and use a ladder with a second person. Never hang the lights from their own cable.

How to hang fairy lights?

Use adhesive hooks, clips or a picture rail so you avoid drilling. Space the clips evenly, keep the lights away from curtains and heaters, and plug into a power board with a safety switch. Check the packet for the hook weight rating, and ask your landlord first in a rental.

Can you hang festoon lights without drilling?

Sometimes. Use freestanding poles, clamp-on brackets or fixings to existing posts and beams. Check that the support can handle the wire tension, and avoid using gutters or fascia that were never designed for the load.

Do festoon lights need an electrician?

Plug-in festoon lights do not, if you use an existing outdoor power point. Adding a new power point or hardwiring the lights is licensed electrical work in NSW, so book a licensed electrician rather than do it yourself.

Getting your festoon lights hung in Sydney

If you would rather not work from a ladder, we can fix the posts, wire and lights in one visit. Book a Sydney handyman and add other hanging jobs. For smaller frames, see the picture hanging guide.