DIY picture framing means cutting four mitred lengths of moulding, gluing and clamping the corners, then fitting glass, your artwork and a backing board. Most people can make a clean frame in one afternoon with a mitre box, wood glue and a corner clamp, or skip the cutting entirely with a ready-cut kit.
This guide covers the tools, a step-by-step method, kits versus custom framing, safe hanging on different walls, and what a Sydney handyman charges to hang the finished frames.
Key points
- A ready-cut DIY frame kit is the easiest start, because the mitres are already cut and the glass or acrylic usually comes in the pack.
- Accurate corners decide how a frame looks, so a mitre box and a corner clamp or strap are the tools worth buying.
- Heavy frames and mirrors need studs or rated anchors on the wall; check the packet and scan for cables before drilling.
- A Sydney handyman charges about $125 for picture and shelf hanging (range $80–$205 per visit), or $105 an hour.
DIY picture framing: tools and materials
You do not need a full workshop; a few good hand tools handle most frames.
| Item | What it’s for | Tip |
|---|---|---|
| Picture frame moulding | Forms the four sides of the frame | Buy a little extra length so a bad cut does not stop the job; Bunnings and framing suppliers sell lengths and offcuts. |
| Mitre box and fine-tooth saw | Cuts accurate corner angles | Clamp the moulding firmly, and cut with the decorative face up to avoid chipping. |
| Wood glue | Bonds the mitred corners | Use a quality PVA wood glue, and check the bottle for open time and clamp time. |
| Corner clamps or band clamp | Holds corners square while the glue sets | Check each corner with a square before leaving it to dry. |
| Glass, acrylic and backing board | Protects and supports the artwork | Acrylic is lighter and safer for large frames; glass gives a clearer finish for small pieces. |
| Hanging hardware | D-rings, wire and picture hooks | Match the hardware to the frame weight, and check the packet rating before you buy. |
| Gloves and eye protection | Protects against glass edges and dust | Wear gloves when handling glass, and keep offcuts away from children and pets. |
DIY picture framing step by step
This method suits a timber frame with a rebate, glass and a hardboard backing.
- Measure your artwork, then add a small allowance so it sits inside the rebate without being forced or squeezed.
- Mark the moulding lengths along the longest edge of each piece, so the mitres run in opposite directions at each end.
- Cut each piece in the mitre box using a fine-tooth saw, keeping the cut steady and the offcut supported.
- Dry-fit the four pieces on a flat surface, check the corners close tightly, and trim any piece that is slightly long.
- Glue each mitre, assemble the frame with corner clamps, check it is square, and wipe off squeezed-out glue immediately.
- Leave the frame to dry for the time on the glue bottle, then lightly sand, stain or paint it before fitting the artwork.
- Clean the glass or acrylic, lay the artwork face down on it, add a mat or spacer if you want one, and add the backing board.
- Fix the backing with points or small brad nails, add D-rings and wire, and tape the edges to keep dust out.
DIY picture frames from timber, recycled or flat-pack parts
Your choice of starting material affects cost, finish and how forgiving the build is.
- New picture moulding gives the cleanest finish, and it is the best choice if you want to stain or paint to match a room.
- Recycled timber and offcuts suit rustic frames, but check for nails, warping and old paint that may contain lead in older homes.
- Flat-pack frames from IKEA or craft stores need no cutting at all, so they suit a first project.
- Thin lightweight timber is easier to cut, but it flexes, so reinforce corners with glue and small corner keys on large frames.
- Seal raw timber before it goes near artwork, because bare wood can release acids that discolour paper over time.
- Always wear a mask when sanding old painted timber from pre-1990 homes, and test for lead paint if you are unsure.
DIY picture frame kit: what is in the box
A kit trades a little flexibility for speed and consistent corners.
| Kit type | What you get | Best for |
|---|---|---|
| Ready-cut timber kit | Pre-mitred sides, glue, backing and hardware | Beginners who want a neat result with minimal tools |
| Snap-together metal kit | Aluminium sides, corner pieces and a clip-in back | Posters, prints and quick changes without glue |
| Canvas stretcher kit | Stretcher bars, keys and fixings | Stretching your own canvas or fabric art |
| Shadow box kit | Deep frame, backing and spacers | Memorabilia, medals and 3D objects |
| Float frame kit | Spacers and clips that hold a canvas off the wall | Canvas work where you want a floating look |
| Custom-cut moulding pack | Lengths cut to your size by a supplier | Odd sizes where you want to do the gluing yourself |
DIY picture framing cost vs custom framing
A DIY frame costs less in materials, but the saving depends on size, glass and how many mistakes you make (indicative — get itemised quotes).
| Option | Typical cost | Notes |
|---|---|---|
| DIY frame from moulding | $30–$150 per frame (indicative) | Cheapest, but you need tools and time |
| DIY frame kit | $25–$120 per frame (indicative) | Easy start; glass is often included |
| Ready-made frame from a store | $20–$200 (indicative) | Quick, but sizes are limited |
| Custom framing shop | $150–$600 or more (indicative) | Best for valuable art, mats and conservation glass |
| Handyman to hang the finished frames | $80–$205 per visit (typical $125) | Sydney, incl GST (Oct 2026) |
| Handyman hourly rate | $57–$140 (typical $105) | Sydney, incl GST (Oct 2026) |
DIY frames: hanging them safely on different walls
A well-made frame still needs the right fixing, and our guide to hanging pictures covers every wall type in detail.
- Scan the wall for cables and pipes before drilling, and avoid the vertical and horizontal lines running from power points and switches.
- Use picture hooks for light frames, and screw into studs or use rated anchors for heavy frames; check the packet rating.
- Use a second person for large frames or anything above shoulder height, and keep a stable ladder close.
- For plasterboard with no stud, use a hollow-wall anchor and never guess the weight it will hold; see our heavy mirror hanging guide.
- If you are renting, ask the landlord in writing; NSW landlords cannot unreasonably refuse picture hooks, nails or screws for hanging frames.
- Treat fibro and old sheeting in a pre-1990 home as possible asbestos, and check asbestos.nsw.gov.au before you drill; our picture rail hanging systems guide shows a no-drill alternative.
Common DIY picture framing mistakes to avoid
- Measuring the artwork without an allowance, so it will not sit in the rebate or is forced and warps.
- Skipping the dry-fit, then gluing corners that do not close, which leaves visible gaps you cannot sand out.
- Using too little clamp pressure or moving the frame early, so the glue joint opens when you pick it up.
- Choosing hanging hardware by looks instead of the packet rating, then watching the frame fall in a few weeks.
- Drilling without scanning for cables and pipes, or into a pre-1990 wall without checking for asbestos.
- Handling large glass alone, which risks cuts and breakage; use acrylic for big frames and wear gloves.
FAQ: DIY picture frames
How do you make a DIY picture frame?
Cut four mitred lengths of moulding, glue and clamp the corners, check the frame is square, then fit the glass, artwork and backing. Add D-rings and wire at the back. A ready-cut kit skips the cutting and glue steps.
Is a DIY picture frame kit worth buying?
Yes, for a first frame or standard sizes. Kits cut the mitres for you and include hardware, so you only assemble. For odd sizes or valuable artwork, a custom-cut moulding pack or a framing shop gives better control.
What tools do I need for DIY frames?
A mitre box, fine-tooth saw, wood glue, corner clamps, a square and hanging hardware are enough for a timber frame. Add gloves and eye protection if you handle glass, and a mask if you sand old painted timber.
Can a handyman hang my DIY frames?
Yes. A Sydney handyman typically charges about $125 for picture hanging, with a range of $80 to $205 per visit (October 2026). Heavy mirrors, masonry and tiled walls take longer and may cost more.
Getting your frames hung in Sydney
Once your frames are made, we can hang them level and secure on any wall type. See the full wall guide in how to hang pictures, then book a Sydney handyman to do the drilling, spacing and levelling in one visit.


