How Much Do Blinds Cost?

How much do blinds cost to install in Sydney? A handyman typically charges about $125 for a small fitting job (range $80–$205 per visit, October 2026), while the blinds themselves vary widely (indicative — get itemised quotes). Size, fabric, style and whether they are made to measure drive the price far more than the labour.

This guide covers how much blinds cost, how to install and remove roller blinds yourself, how to hang venetian and vertical blinds, and when it pays to book someone.

Key points

  • Labour is the smaller part of the bill: a Sydney handyman typically charges about $125 per small fitting visit, with blinds priced separately by size and style.
  • Window size, fabric and made-to-measure orders are the biggest cost drivers, so measure carefully before you buy or order.
  • The cheapest route is a ready-made or click-fit blind that you fit yourself, which suits standard windows with solid timber or masonry for the brackets.
  • DIY is fine for a roller blind at ground level; use a second person and a stable ladder for high windows, long blinds and anything over a door.

How much do blinds cost? Price table

Blind prices depend on the product, so the table splits the bill into what you can pin down and what you must quote. Labour figures include GST and come from October 2026 Sydney data.

JobBlinds and fittingsLabour (Sydney)What decides the total
One roller blind, standard windowVaries by size and fabric (indicative — get itemised quotes)$80 / $125 / $205 (low / typical / high)Fabric type, width and whether it is ready-made or made to measure
Several blinds in one visitVaries by number and size (indicative — get itemised quotes)Half day: $230 / $415 / $645Number of windows, ladder access and how many have different brackets
Whole-house fit-outVaries widely (indicative — get itemised quotes)Full day: $435 / $690 / $1025Mix of blind types, window heights and any old blinds to remove
Short visit for one quick fixUsually nil if you supply the blindMinimum charge: $92 / $140 / $170The call-out applies even for a five-minute fix

How much do blinds cost by city?

Handyman labour is the part you can compare across cities. Blind prices themselves track the product, not the postcode.

CityHourly rate (low / typical / high)Call-out or minimum charge
Sydney$57 / $105 / $140$92 / $140 / $170
Melbourne$52 / $94 / $125$84 / $125 / $160
Brisbane, Perth and AdelaideVaries (indicative — get itemised quotes)Varies (indicative — get itemised quotes)

What affects the price of blinds

  • Window width and drop set the fabric needed, so wide living-room windows and sliding doors cost much more than a bathroom window.
  • Fabric changes the price: sheer, light-filtering and blockout rolls differ, and thermal or UV-rated fabrics usually cost extra (indicative — get itemised quotes).
  • Made-to-measure blinds cost more than ready-made sizes, but they fit inside the frame properly and avoid light gaps at the sides.
  • Style matters: roller blinds are usually the simplest, while venetian, vertical and motorised blinds add parts, tracks and fitting time.
  • Access affects labour, because high windows, stairwells and bay windows need a ladder and a helper, which adds time on site.
  • Old blinds to remove add time, and brackets in brittle plaster or old render may need new anchors.
  • Minimum charges apply to short visits, so one blind on its own costs more per window than six done at once.

DIY vs hiring a pro for blinds

Do it yourselfBook a handyman
Standard window, ready-made or click-fit roller blind, solid timber or masonry for the bracketsWide windows, bay windows, stairwells or any bracket above shoulder height
You own a drill, level and stud finder, and the wall has been scanned for cables and pipesYou have several blinds, mixed styles or old blinds to take down first
You are renting and the landlord has agreed, since internal removable blinds are a minor change they cannot unreasonably refuseBrackets must go into tile, render, fibro or a pre-1990 home with possible asbestos
The blind comes with clear manufacturer instructions for the fixingsYou want a power point, motor or hardwired fitting, which needs a licensed electrician such as TQN Electrician

How to install roller blinds: step by step

This covers a standard roller blind with brackets, including the inside-mount and click-fit versions. Keep blind cords and chains well out of reach of small children.

  1. Measure the window in three places and use the smallest width for an inside mount, checking there is enough depth in the recess for the brackets.
  2. Check the blind and bracket pack against the window, deciding on inside mount (inside the frame) or outside mount (on the wall or architrave).
  3. Scan the fixing points for cables and pipes, and find a stud, lintel or solid frame, avoiding the lines running from nearby switches.
  4. Mark the bracket positions level with a pencil, hold the bracket in place and check it with a spirit level before you drill.
  5. Drill pilot holes, use the anchors the packet recommends for your wall, and tighten the screws until snug without crushing plasterboard.
  6. Fit the bracket covers or clips if the blind has them, then check both brackets are level and the same distance from the frame.
  7. Click or slide the blind into the brackets, following the maker’s instructions for the correct side for the chain or control.
  8. Roll the blind up and down a few times, check it tracks straight, and adjust the brackets if it drifts to one side.

How to remove a roller blind from its brackets

Removing a roller blind is quick once you know which type of bracket you have. Ask a helper to steady the ladder for high windows.

  • Roll the blind fully up first, so the fabric is tight and the tube is easy to hold with both hands.
  • Look at the end of the tube to see whether it has a pin, a clip or a slot on the bracket side.
  • Push the spring-loaded pin side inward to free it, then lift the tube up and out of the bracket on the other side.
  • Press or slide any bracket clip, or lift the tab on a click-fit bracket, to release the blind without bending the tube.
  • Unscrew the brackets once the blind is off, and patch the holes with filler if you are leaving the window bare.
  • In a rental, keep the old blind and brackets for the end of the lease, and ask the landlord about any holes.

How to hang venetian and vertical blinds

Venetian and vertical blinds hang from a headrail, so the fixing method differs from a roller blind. Our types of blinds guide and vertical blind slat guide explain the parts.

  • Fit the headrail brackets level across the top of the window, and mark the position for the end and centre brackets before drilling.
  • Clip the headrail into the brackets until it locks, then check it sits level before you attach the slats or louvres.
  • Hang vertical blind slats from the carriers one at a time, keeping them facing the same way so they rotate evenly.
  • Attach the bottom chain or weights as the instructions say, so the slats hang straight and do not swing.
  • Test the tilt wand or cord, and adjust the brackets if the blind jams or leaves a gap at the window edge.
  • Outdoor and weather-exposed blinds follow different fixing rules, so check our outdoor blinds guide before you buy.

Roller blind parts, chains and easy fit blinds

A blind that jams is often a worn part, not a worn-out blind. Replacement parts are cheap compared with a new blind.

  • Check the chain, clutch and end caps first, because a worn clutch or a loose chain is the usual cause of a blind that won’t hold.
  • Match replacement parts by taking the old clutch, bracket or tube end to a hardware store such as Bunnings, or by quoting the maker’s model number.
  • Click-fit and easy fit blinds use clip-on brackets, which makes DIY fitting quick but still needs solid fixings behind the bracket.
  • Replace a whole blind when the fabric is sun-damaged, the tube has bent or the parts are no longer available.
  • When you replace roller blinds, measure the old blind and the recess again, because the window may have shifted slightly since it was fitted.
  • Our curtain installation cost guide and blinds cost guide compare the options if you are deciding between blinds and curtains.

How to save on blinds without cutting corners

  1. Measure twice, then order the exact size, because a wrongly sized made-to-measure blind is rarely refundable.
  2. Choose ready-made blinds for standard windows and keep made-to-measure for odd sizes or large windows.
  3. Fit blinds in one visit, so a single minimum charge covers every window instead of one charge per room.
  4. Supply the blinds and fixings yourself and pay only for labour, if you are confident the sizes are right.
  5. Compare itemised quotes, not just totals, so you can see whether fixings, ladders and removal are included.
  6. Look at the roller shutters price guide before you commit, because a different product can suit the window better.

What a fair quote for blinds should include

  • An itemised price for each blind, covering the fabric, tube, brackets and any chain or control, with sizes listed.
  • Labour for fitting listed separately, with a clear call-out or minimum charge if the visit is short.
  • Access costs, such as ladders or a second person, for high windows and stairwells.
  • Removal and tidy-up of old blinds and packaging, so you are not left with the clutter.
  • Warranty terms from the supplier or installer in writing, rather than a verbal promise.
  • Licence details for any electrical or building work, since motorised blinds need a licensed electrician and larger jobs have written-contract rules.

FAQ: how much do blinds cost

How much do blinds cost to buy and fit?

The blinds themselves vary widely with size, fabric and style, so get itemised quotes. A Sydney handyman typically charges about $125 to fit blinds on a small job, with a range of $80 to $205 per visit (October 2026). Fitting several together lowers the cost per window.

How to install roller blinds inside mount?

Measure the recess in three places, check it has enough depth, and mark level bracket positions inside the frame. Fix the brackets with the right anchors, click the blind in, then roll it up and down to check it tracks straight and clears the frame.

How to remove a roller blind safely?

Roll the blind up, then release the clip, pin or tab on the bracket and lift the tube out. Use a ladder with a helper for high windows. Unscrew the brackets afterwards and fill the holes. Renters should ask the landlord before changing anything.

How to hang venetian or vertical blinds?

Fix the headrail brackets level at the top of the window, clip the headrail in, then add the slats or louvres. Follow the maker’s instructions for the fixings and the bottom weights. Test the wand or cord, and adjust the brackets if the blind jams.

Getting your blinds fitted in Sydney

If you’d rather not work out how to hang roller blinds yourself, we can measure, fit and test every blind in a single visit, with the right fixings for your wall. Book blind installation in Sydney, and see our curtain rod installation guide if you are fitting curtains at the same time.