Blind installation is a drill, a level and a few brackets: mark the bracket positions, check for cables and studs, fix the brackets level, then clip the blind in. The most common failure is screwing brackets into hollow plasterboard or a soft window frame, so the fixing point decides how the job goes.
This guide covers blind installation step by step, what roller blinds cost, how far DIY motorised blinds can safely go, and what a Sydney handyman charges to fit them. For curtains, see our curtain rod installation guide.
Key points
- Most roller blinds are an eight-step job with a drill, a level and a pencil, and the hard part is a straight fix rather than the clip-in.
- A stud finder or cable detector is the one tool you can’t skip when brackets go into a wall or ceiling face.
- Keep cords and chains out of reach of children, and follow the manufacturer’s instructions for cleats and tension devices.
- A Sydney handyman typically charges $105 an hour (range $57–$140, October 2026), with a $140 typical call-out or minimum charge.
Can you do blind installation yourself?
Most people can fit a single roller or Roman blind in a standard window, but some situations need more care or a licensed trade.
| Your situation | DIY OK? | Why |
|---|---|---|
| Inside-mount roller blind in a timber window frame | Yes | Short screws into solid frame timber hold small brackets well; use the screws the maker supplies and pilot-drill to avoid splitting. |
| Outside mount on plasterboard | Yes, with care | Brackets should go into studs or into anchors suited to plasterboard; check the packet rating rather than guessing. |
| Aluminium or steel window frames | Experienced DIYers | You need metal-drilling bits and screws designed for thin metal, and a slip can scratch the frame. |
| Tall or wide windows and sliding doors | Two people | A long headrail bows if one person lifts it; a second person also holds the level. |
| Tiled or masonry reveals | Check first | Tiles crack easily and masonry needs a hammer drill, so take care or book a handyman. |
| Renting | Ask first | Removable blinds are among the minor changes NSW tenants can request, but you need consent before drilling. |
| Motorised blind that needs a power point | No | New or moved power points are electrical work and need a licensed electrician in NSW. |
Tools and materials for blind installation
| Item | What it’s for | Tip |
|---|---|---|
| Blind and bracket kit | Holds the headrail on the wall or frame | Use the fixings supplied only when they suit your surface; otherwise buy ones matched to the wall type. |
| Tape measure and pencil | Marks bracket positions | Measure the window in three places and use the smallest width for an inside mount. |
| Spirit level | Keeps the blind straight | A level beats eyeballing, because a tilt shows as soon as the blind rolls down. |
| Cordless drill and bits | Pilot holes and screws | Pick the bit for timber, masonry or metal, and drill slowly so the bit doesn’t wander. |
| Stud finder with cable detection | Finds framing, cables and pipes | Scan above and beside the window, because wiring often runs from nearby switches. |
| Stepladder | Reaches the top of the window | Use a stable ladder and a second person for anything above shoulder height. |
| Cord cleat or tension device | Keeps loop cords out of reach | Fit it as the maker instructs, at a height children can’t reach. |
Blind installation: step by step
Allow time for a second person to hold the blind while you check it for level.
- Decide on an inside or outside mount, measure the window opening in three places, and note the blind’s bracket spacing from the instructions.
- Check the area for cables with a detector, avoiding lines running vertically and horizontally from switches and power points near the window.
- Hold the first bracket where the instructions say, mark the screw holes in pencil, and repeat on the other side with the level between them.
- Drill pilot holes for each bracket, using the right bit for timber, masonry or metal, and vacuum the dust out of masonry holes.
- Fix each bracket firmly with the correct screws, recheck both with the level, and stop tightening when snug so you don’t crush plasterboard.
- Clip or slide the blind into the brackets as shown in the manufacturer’s instructions, and make sure the locking tabs engage.
- Roll the blind fully down and up twice to confirm it tracks straight; adjust the bracket if it creeps to one side.
- Fit the cord cleat or tension device out of reach of children, and keep the chain or cord short enough that it can’t form a loop.
Roller blinds cost: what you pay for the blind and the fitting
Roller blinds cost depends on fabric, size, mounting and whether they are made to measure, so treat the figures below as a guide, not a quote.
| Item | What drives it | Guide |
|---|---|---|
| Ready-made roller blind | Standard sizes, basic fabric, no made-to-measure fitting | Lowest cost (indicative — get itemised quotes) |
| Made-to-measure roller blind | Exact width, chosen fabric, block-out or sunscreen | Mid-range (indicative — get itemised quotes) |
| Motorised roller blind | Motor, remote or app control, battery or hardwired | Highest cost (indicative — get itemised quotes) |
| Handyman fitting only | Number of windows, access, wall type | See the Sydney cost table below |
| Removing old blinds | Number of blinds and repairing old screw holes | Often part of the same visit |
| Patching holes left by old brackets | Plaster, filler and paint touch-up | Quoted as minor patching if needed |
DIY motorised blinds: what is safe to do yourself
Battery and solar motors are friendly to DIY, but anything connected to mains power is a licensed electrician’s job.
- Choose a battery-powered or solar-panel motor if you want DIY motorised blinds, because no wiring is involved and you can fit them like a normal blind.
- Check that the motor and headrail suit your blind’s weight and width in the manufacturer’s instructions before you buy.
- Leave enough room for the motor tube on inside mounts, and measure the depth of the window recess before ordering.
- Don’t run mains cables or a plug-in transformer through a wall cavity; book a licensed electrician for a new power point or hardwired motor.
- Keep batteries and charging cables out of children’s reach, and follow the maker’s guidance for charging and replacement.
- Program remote limits (top and bottom stops) before final fixing, and test them with the blind unloaded so the fabric doesn’t strain.
Blind installation for rentals and units
In Sydney units, concrete lintels and metal frames are common, so check the surface before you pick your fixings.
- Ask your landlord or strata in writing before drilling; NSW lets tenants request internal curtains or removable blinds, but you still need consent.
- Choose a tension or no-drill blind if the frame is metal or the landlord says no, and check the maker’s weight limits for the model.
- Photograph the window before and after, so there is a record of the original condition for the end of the lease.
- Fill unused screw holes with filler before you move out, and agree who patches paint with your landlord.
- In older units, check for asbestos in eaves or wet-area linings before drilling above bathrooms or laundries: homes built or renovated before 1990 are likely to contain it.
- Remember that heritage properties and strata buildings have extra limits, so confirm the rules with your property manager.
Common mistakes with blind installation
- Using the plastic plugs in the box in plasterboard for a heavy block-out blind, instead of fixings matched to the wall and the blind’s weight.
- Skipping the cable scan and drilling above a window where a power cable runs from the switch to the point.
- Trusting the window frame is square, then finding the blind creeps to one side after it is hung.
- Overtightening screws into soft timber or plasterboard, which strips the hole and loosens the bracket within weeks.
- Ignoring asbestos risk when drilling old eaves or sheeting in a pre-1990 home.
- Leaving a loop cord dangling where a child can reach it, rather than fixing a cleat as the instructions show.
When to call a handyman for blind installation (or a licensed trade)
- You have several windows, wide sliding doors or high stairwell windows that need a ladder and a second person.
- The wall is tiled, rendered, fibro or part of a pre-1990 home where hidden asbestos or cracking is a risk.
- You want motorised blinds powered from the mains, which needs a licensed electrician such as TQN Electrician.
- The frame is aluminium or steel, and you don’t have the right drill bits or fixings.
- You need old blinds removed and plaster holes patched before new blinds go up.
- You are renting and want the job done neatly, so the holes can be patched cleanly when you move out.
Cost to hire a handyman for blind installation in Sydney
Prices below include GST and come from October 2026 Sydney and Melbourne metro data. Our curtain installation cost guide covers similar jobs.
| Job | Low | Typical | High |
|---|---|---|---|
| Handyman hourly rate, Sydney | $57 | $105 | $140 |
| Call-out or minimum charge, Sydney | $92 | $140 | $170 |
| Comparable small fixing job (picture or shelf hanging), Sydney | $80 | $125 | $205 |
| Half-day handyman, Sydney (4 hours) | $230 | $415 | $645 |
| Handyman hourly rate, Melbourne | $52 | $94 | $125 |
- Blinds are usually extra unless you supply them, so ask whether the quote includes brackets, fixings and old-blind removal.
- Book several windows in one visit, because the minimum charge is paid once rather than for each blind.
- Not sure which style suits each room? Our types of blinds guide compares them, and the roller blind guide goes deeper on that style.
FAQ: blind installation
How much do roller blinds cost?
Roller blinds cost more as you move from ready-made to made-to-measure to motorised (indicative — get itemised quotes). Fabric, window size and mounting all change the price. Ask for an itemised quote that separates the blind, brackets, fitting and any removal of old blinds.
Can you do DIY motorised blinds without an electrician?
Yes, if the motor runs on a battery or solar panel and you fit it like any other blind. A mains-powered motor, or a new power point near the window, is electrical work and needs a licensed electrician in NSW.
How long does blind installation take?
One straightforward roller blind usually takes under an hour once you have the tools out, but allow longer for several windows, metal frames or masonry. A handyman will often fit a whole house in a half-day booking.
Do you need to drill to install blinds?
Most blinds need screws into the frame or wall. Tension and no-drill blinds exist for renters or metal frames, but check the weight and size limits in the maker’s instructions. Your landlord’s written consent is still wise.
Getting blind installation done in Sydney
If you’d rather skip the ladder and the drilling, we can fit your blinds level, secure and child-safe in one visit. Our handymen carry detectors, masonry and metal bits and the right fixings for your frame. Book blind installation in Sydney and add any other small jobs to the same booking.


