DIY honeycomb blinds are a realistic weekend job: measure the window twice, order the blind to size, mark the bracket positions level, drill and fix, then click the headrail in. The thing that goes wrong most often is a measuring error, because made-to-measure blinds usually can’t be returned.
This guide covers DIY honeycomb blinds, how to put up venetian blinds, blackout options, and what vertical, roller and blackout blinds cost, so you know when to do it yourself and when to book a hand. For fixing methods at the window, see our curtain rod installation guide.
Key points
- Most blinds install in about eight steps with a drill, level and tape measure, and the order of measuring, marking and fixing matters more than speed.
- The tool you can’t skip is a stud or cable detector when you are drilling into a plasterboard reveal or lintel, because wiring sometimes runs above windows.
- Keep cords out of children’s reach, fit the safety devices that come with the blind, and follow the maker’s instructions.
- A Sydney handyman charges about $140 as a typical call-out and around $105 an hour (October 2026), so one visit often covers every blind in a room.
DIY honeycomb blinds: can you do it yourself?
Honeycomb (cellular) blinds trap a layer of air in their folded cells, which helps with heat and noise. Installation is simple, but the measuring has to be exact.
| Your situation | DIY OK? | Why |
|---|---|---|
| Standard window, inside mount in a timber or aluminium frame | Yes | Small brackets fix to the frame, and the blind clips into the headrail. |
| Outside mount on plasterboard | Yes, with a detector | Scan for cables and pipes, then use anchors rated for the blind and wall type. |
| Wide window or large blind | With a helper | A wide headrail is awkward to hold level and fix at the same time. |
| High window above shoulder height | Only with a second person | Work from a stable ladder with someone spotting you. |
| Pre-1990 home with fibro or old sheeting around the window | Check first | Don’t drill into suspect material until you have identified it. |
| Rental property | Ask first | In NSW tenants can request removable blinds, but you need consent before you fix anything, and the landlord can’t unreasonably refuse. |
DIY honeycomb blinds: step by step
Block out an hour or two per window and allow time for a second person if the blind is wide. Follow the manufacturer’s instructions, because brackets and clips differ between brands.
- Measure the width of the recess at the top, middle and bottom, and use the narrowest figure for an inside mount.
- Measure the drop on the left, middle and right, then order the blind to the size shown in the maker’s guide.
- Check the window frame and reveal for depth, and confirm the headrail fits inside before you drill anything.
- Mark the bracket positions with a pencil and a level, keeping them evenly spaced and the same distance from each end.
- Scan the area for cables and pipes if the brackets go into plasterboard, then drill pilot holes to the depth the fixing maker states.
- Screw the brackets on firmly, using wall anchors rated for the blind where there is no stud or timber behind.
- Clip the headrail into the brackets, close the safety latch if one is supplied, and check it holds when tugged gently.
- Run the blind up and down to test the operation, then adjust the cord or chain tension and fit the child-safety devices.
DIY blackout blinds and DIY black out blinds
Blackout blinds block light with a dense or coated fabric, and the gaps at the sides often matter as much as the fabric itself.
- Choose a roller or honeycomb blind with a blackout fabric for bedrooms and nurseries, and check the product label for what it blocks.
- Pick an outside mount that overlaps the window frame on each side, which cuts the light leaking around the edges.
- Add side channels or a pelmet if you want near-complete darkness, as the gap around a standard headrail lets light through.
- Consider a blackout liner behind existing curtains if you rent, because it needs no drilling and takes minutes to hang.
- Measure carefully for the recess or overlap, since blackout fabrics are made to measure and can’t be cut down at home.
- Check the fabric label for the blackout rating and the care instructions, because the coating on some fabrics marks if you wipe it with the wrong cleaner.
How to put up venetian blinds
Venetian blinds use slats on a tilt wand or cord, and the headrail goes up the same way as most blinds. Our guide to installing roller blinds covers the roller version.
- Measure the recess and decide inside or outside mount, remembering that venetians need clearance for the slats to turn.
- Hold the headrail against the window and mark both ends and the bracket positions with a level.
- Fit the brackets to the window frame or wall, using the screws supplied for timber and anchors for plasterboard.
- Clip the headrail into the brackets, then hang the slats from the rail and check the tilt wand runs smoothly.
- Check the blind sits level, adjust the lift cord tension, and fit any cord safety device included.
Cost of vertical blinds and how much do vertical blinds cost
Prices vary widely between ready-made and made-to-measure vertical blinds, so these figures are a rough guide only. Our vertical blind replacement slats guide shows a cheaper way to refresh a tired blind.
| Option | Typical price range | What affects it |
|---|---|---|
| Ready-made vertical blind for a standard window | About $60 to $180 (indicative — get itemised quotes) | Size, fabric and brand |
| Made-to-measure vertical blind for a sliding door | About $200 to $700 (indicative — get itemised quotes) | Width, fabric and the track system |
| Replacement slats only | Often well below a full blind (indicative — get itemised quotes) | Number of slats, fabric and brand |
| Handyman installation, Sydney | From $140 call-out, typically $105 an hour | Number of blinds and access (October 2026) |
Blackout blinds cost and roller blind price
The fabric and the size drive most of the cost, and our blinds cost guide compares every type in detail.
| Blind type | Typical price range | Best for |
|---|---|---|
| Roller blind (standard fabric) | About $40 to $200 (indicative — get itemised quotes) | Bedrooms, offices and kitchens |
| Blackout roller blind | About $60 to $250 (indicative — get itemised quotes) | Bedrooms and shift workers |
| Honeycomb blind (single cell) | About $100 to $350 (indicative — get itemised quotes) | Insulation and light control |
| Venetian blind (aluminium or timber) | About $60 to $300 (indicative — get itemised quotes) | Light control in living areas |
| Outdoor blinds and roller shutters | Higher, with a licensed installer for powered units (indicative — get itemised quotes) | Patios and security; see outdoor blinds and roller shutters price |
- Installing curtains instead? Our curtain installation cost guide compares the labour for each.
- One visit usually covers every blind in the room, and a full day can cost less than eight hourly-billed hours (October 2026).
- Powered blinds that need a new power point need a licensed electrician; book one instead of wiring it yourself.
Common mistakes with DIY blinds
- Measuring once, at one point, instead of at the top, middle and bottom of the window.
- Drilling into plasterboard without scanning for cables and pipes above the window.
- Skipping the level, so the blind drifts to one side and the slats or fabric hang crooked.
- Overtightening screws until the bracket cracks or the plasterboard crumbles.
- Leaving cords loose within reach of children, instead of fixing the cleats and tension devices that come with the blind.
- Drilling into old fibro or eaves in a home built or renovated before 1990 without checking for asbestos.
FAQ: DIY honeycomb blinds and blinds cost
How to put up venetian blinds?
Measure the recess, mark the bracket positions with a level, and fix the brackets to the frame or wall. Clip the headrail in, hang the slats, and test the tilt wand and lift cord. Fit any cord safety device supplied before you finish.
How much do vertical blinds cost?
A ready-made vertical blind for a standard window may cost around $60 to $180, while made-to-measure sliding-door blinds cost more (indicative — get itemised quotes). Replacing just the slats can be cheaper than buying a new blind.
Can I do DIY blackout blinds in a rental?
Yes, if you choose a removable option or ask your landlord for consent first. NSW law lets tenants request removable blinds and a landlord cannot unreasonably refuse, but you should ask before drilling. A tension-fit blind or liner avoids holes.
Are honeycomb blinds hard to install?
No, installation is similar to a roller blind: fix two or three brackets level, then clip the headrail in. The hard part is measuring, since made-to-measure blinds are rarely returnable. Follow the maker’s instructions and use a second person for wide windows.
If you would rather have the measuring, drilling and fitting done in one visit, book blind installation in Sydney, or return to the curtain rod guide for fixing basics.


