Window Shutter Installation: Step-by-Step Guide & Costs

Window shutter installation is a measure, dry-fit, drill and hang job: you fix the frame into the window reveal with a drill, spirit level and packers, then hang the hinged panels. The biggest thing that goes wrong is a bad measurement, because made-to-measure shutters cannot be trimmed on site if the opening is out of square. This guide covers DIY plantation shutters, mounting types, renting, and what a Sydney handyman charges.

Key points

  • Difficulty is moderate and the job runs to 9 steps, with accurate measuring and a careful dry-fit doing most of the work.
  • The one tool you cannot skip is a spirit level, because a frame that is not plumb and square makes panels bind or drift.
  • Scan for cables and pipes before drilling, and check for asbestos in pre-1990 window reveals, eaves and fibro cladding.
  • A Sydney handyman charges $57–$140 an hour (typical $105) incl GST, and a small fixing job typically costs $80–$205 per visit.

Can you do window shutter installation yourself?

Pre-made kits suit confident DIYers; windows that are high, large, out of square or in older homes often need a second pair of hands or a handyman.

SituationDIY OK?Why
Standard window, kit supplied, plasterboard or timber revealYes, with a helperPanels are awkward to hold while fixing, so work with a second person.
Tall, wide or upper-storey windowHandymanHeavy panels above shoulder height need a second person and a stable ladder.
Brick or masonry revealHandyman or confident DIYYou need a hammer drill and masonry fixings matched to the wall; check the packet.
Pre-1990 house with fibro or old sheetingCheck firstTreat suspect material as asbestos and check asbestos.nsw.gov.au before drilling.
Rented homeAsk firstShutters are fixed, and the landlord cannot be assumed to agree, so get written consent.
Window with wiring or a blind motor nearbyLicensed electrician for wiringNever move or touch wiring yourself; book a licensed electrician.

Tools and materials for window shutter installation

Your supplier’s kit should list fixings, and the installation sheet decides the details.

ItemWhat it is forTip
Steel tape and pencilMeasuring the opening and marking fixing pointsMeasure in several places and use the smallest figure.
Spirit levelChecking the frame is plumb and levelA longer level shows twist better than a short one.
Cable and stud detectorFinding wiring, pipes and framing before you drillAvoid lines running straight up or across from power points and switches.
Drill and bitsPre-drilling fixing holesRyobi and Makita are common; use masonry bits for brick reveals.
Packers or shimsLevelling the frame in an uneven openingPack behind each fixing so the frame is not pulled out of shape.
Dust mask, glasses and glovesProtecting you from dust and glass or sharp edgesWear a mask whenever you drill into old reveals.

Window shutter installation: step by step

Follow your supplier’s installation sheet, because frame types and fixing positions differ by brand.

  1. Measure the width and height of the opening at three points each, record the smallest, and check the corners with diagonal measurements.
  2. Order made-to-measure shutters using the supplier’s measuring guide, and confirm the frame type and whether the shutters mount inside or outside the reveal.
  3. Unpack and check every panel, hinge, frame piece and fixing against the parts list before you pick up a drill.
  4. Dry-fit the frame in the opening, check it with the spirit level, and mark where packers are needed to bring it plumb and square.
  5. Scan the reveal for cables, pipes and studs, then mark fixing points that avoid them and suit the wall type.
  6. Pre-drill and fix the frame through the jambs with fixings matched to the wall, following the maker’s spacing and packer positions.
  7. Re-check that the frame is square and not bowed, and adjust packers before you tighten each fixing fully.
  8. Hang the panels on their hinges as the instructions direct, adjusting until gaps are even and the louvres close cleanly.
  9. Fit the tilt rod, catches and trims, then fill or caulk any gaps between the frame and wall.

Window shutter installation inside vs outside the reveal

The mount decides how you measure, how much light you lose and how the finished window looks.

  • Inside mount sits within the reveal for a neat look, but it needs a deep, square opening that fits the frame.
  • Outside mount sits on the wall around the window, hiding uneven openings, but it needs solid fixing into wall framing or masonry.
  • Shallow or out-of-square reveals, common in older terraces, often suit an outside mount, so ask the supplier.
  • Check window handles, winders and locks do not collide with the panels when they open.
  • Confirm in advance how the panels will fold or swing, so furniture and curtains do not block them.

Measuring for plantation shutters

Measure carefully and measure twice, because a wrong figure usually means reordering.

  • Measure width at the top, middle and bottom of the opening and use the smallest figure unless the supplier says otherwise.
  • Measure height at left, centre and right, and note any sloping sills or bulging plasterboard that will affect the frame.
  • Check the corners with diagonal measurements; a difference between them shows the opening is out of square.
  • Record the depth of the reveal so the supplier can check whether an inside mount is possible.
  • Photograph the window and write down which way it opens, so panels and hinges are specified correctly.

Window shutter installation in a rental or strata home

Shutters are a fixed change, so approval matters before you order anything.

  • In NSW a landlord cannot unreasonably refuse minor changes such as internal curtains or removable blinds, but fixed shutters are not on that list.
  • Ask for written consent from the landlord before you order, and keep a copy of the reply.
  • Strata owners should check by-laws and committee rules about window appearance and fixings before ordering.
  • If consent is refused, curtains and removable blinds are the alternative; see our types of blinds guide.
  • Heritage properties and loose-fill asbestos register homes have extra limits, so check before you plan any fixing.

Common mistakes with window shutter installation

  • Using one measurement for the whole opening instead of the smallest of several, then finding the frame will not fit.
  • Fixing the frame without packers, so the frame twists as the fixings tighten and the panels bind.
  • Skipping the cable and pipe scan before drilling into the reveal or the wall beside the window.
  • Using plasterboard-only fixings for the frame when the maker calls for fixing into framing or masonry.
  • Drilling old fibro or eave sheeting in a pre-1990 home before checking for asbestos at asbestos.nsw.gov.au.
  • Lifting panels alone or working above shoulder height without a second person and a stable ladder.

When to call a handyman (or a licensed trade)

  • The window is tall, wide or upstairs, and you want the panels hung safely by a team of two.
  • The reveal is brick, concrete or out of square, and fixings need to be chosen to suit the wall.
  • The home is pre-1990 and the surrounding material might contain asbestos; stop and get it identified.
  • Wiring or a switch sits close to the window, which needs a licensed electrician rather than a DIY change.
  • The window itself is damaged or leaking, which may need a glazier or builder; building work valued over $5,000 needs a licensed builder.
  • You want several fittings installed in one visit: curtains, blinds and shutters together with an itemised quote.

Cost to hire a handyman for window shutter installation in Sydney

Handyman rates include GST and come from October 2026 Sydney data; the shutter supply and install rows are indicative estimates.

JobLowTypicalHigh
Handyman hourly rate, Sydney$57$105$140
Call-out or minimum charge$92$140$170
Small fixing job (comparable to hanging a shelf or picture)$80$125$205
Half-day handyman (4 hours)$230$415$645
Full-day handyman (8 hours)$435$690$1025
Install one pre-made shutter set, labour only$120 (indicative)$200 (indicative)$350 (indicative)
Supply of made-to-measure plantation shutters, per m²$350 (indicative)$600 (indicative)$900 (indicative)

FAQ: window shutter installation

Can you install plantation shutters yourself?

Yes, if the opening is standard and you have a helper. Measure carefully, dry-fit the frame, check it with a spirit level and fix it with the right fixings for your wall. Tall windows, brick reveals and older homes are better left to a handyman, especially when asbestos is possible.

How much does window shutter installation cost?

Installation labour for a pre-made set is often about $120–$350 per window (indicative — get itemised quotes), plus the shutters themselves. A Sydney handyman charges $57–$140 an hour and a call-out of $92–$170, so ask for an itemised quote.

Inside mount or outside mount for shutters?

Inside mount suits deep, square reveals and gives a tidy finish. Outside mount hides uneven openings and shallow reveals but needs solid fixing into the wall. Ask your supplier which suits your window, and measure the reveal depth before ordering.

Do I need landlord approval for shutters?

Yes. In NSW, tenants can ask for certain minor changes such as internal curtains and removable blinds, but fixed shutters are not on that list. Get the landlord’s written consent before ordering, and do not drill without it.

Getting window shutter installation done in Sydney

If you would rather have the panels hung level and the gaps even, we can measure, fix and adjust them in one visit. Book a Sydney handyman for window shutter installation, and start with our curtain rod installation guide, plus outdoor blinds, roller blind installation and vertical blind slat replacement for other window treatments.