How Much to Build a Deck per Square Metre?

How much to build a deck per square metre in Australia? Typically about $250–$900 installed, from treated pine at ground level to composite or a raised hardwood deck (indicative — get itemised quotes). The decking material, the height off the ground and the state of the site decide where you land in that range. This guide gives price bands, a worked example, city notes and a quote checklist, and our how to build a deck guide covers the method.

Key points

  • Plan on roughly $250–$900 per m² installed, with ground-level treated pine at the low end and raised or composite decks at the top (indicative — get itemised quotes).
  • The biggest cost driver is height and slope, because a raised deck needs more framing, bracing and often a licensed builder.
  • The cheapest option is a ground-level treated pine deck that stays within the exempt development limits.
  • DIY is realistic for a small, low deck, but any building work valued at more than $5,000 must be done by someone licensed by Building Commission NSW.

How much to build a deck per square metre: price table

These bands include framing, decking boards, fixings and labour on a typical suburban site.

Deck typeMaterials per m²Labour per m²Total per m²
Treated pine, ground level$90–$160 (indicative)$160–$290 (indicative)$250–$450 (indicative)
Hardwood such as merbau or spotted gum, ground level$140–$250 (indicative)$210–$400 (indicative)$350–$650 (indicative)
Composite decking, ground level$180–$330 (indicative)$270–$570 (indicative)$450–$900 (indicative)
Raised hardwood deck on a sloping block$200–$350 (indicative)$300–$500 (indicative)$500–$850 (indicative)
New boards over an existing sound frame$100–$250 (indicative)$90–$200 (indicative)$190–$450 (indicative)
Compact hardwood deck, where fixed costs spread over fewer m²$150–$260 (indicative)$300–$480 (indicative)$450–$740 (indicative)
  • Stairs, balustrades, steps, lighting and privacy screens are normally extras, so ask for them as separate lines.
  • Check supplier price lists for the actual board you want, because species and profile shift the board cost.
  • Exempt development covers decks up to 25 m² each, so confirm the limits with council before you price a bigger deck.

How much does a deck cost? A worked example

Take a 5 m by 4 m deck, which is 20 m² and sits inside the 25 m² exempt limit for a single deck.

  • Treated pine at ground level: about $5,000–$9,000 for the whole deck (indicative — get itemised quotes).
  • Hardwood at ground level: about $7,000–$13,000 (indicative — get itemised quotes).
  • Composite at ground level: about $9,000–$18,000 (indicative — get itemised quotes).
  • Raised hardwood on a slope: about $10,000–$17,000 (indicative — get itemised quotes).
  • Every row exceeds $5,000 at the upper end, so the builder must be licensed by Building Commission NSW.
  • Above $20,000 you need a full home building contract plus Home Building Compensation cover.

How much to build a deck per square metre by city

Only Sydney and Melbourne handyman rates are verified, so use them as a labour benchmark and collect local quotes elsewhere.

CityHandyman hourly rateCall-out or minimumDeck guidance
Sydney$57–$140 (typical $105)$92–$170 (typical $140)Use the price table; sloping lots, tight access and sandstone footings raise framing cost.
Melbourne$52–$125 (typical $94)$84–$160 (typical $125)Labour rates run a little lower, but timber and board prices follow national supply.
BrisbaneNo verified rate heldNo verified rate heldGet three itemised local quotes and ask about termite protection for framing.
PerthNo verified rate heldNo verified rate heldGet three itemised local quotes and compare timber species line by line.
AdelaideNo verified rate heldNo verified rate heldGet three itemised local quotes and compare timber species line by line.
  • Sandstone and clay soils change footing depth and drainage, so a site visit often alters a phone estimate.
  • Timber prices move with supply, so ask how long a written quote stays valid before you commit.
  • Always compare the same scope: a cheap quote that leaves out stairs, balustrades or waste removal is not cheaper.

What affects how much a deck costs per square metre

Six items move a quote up or down inside each band.

  • Material: composite and hardwood boards cost more than treated pine, but they change maintenance as well as price.
  • Height and slope: a floor higher than 1 m above ground falls outside the exempt limits and needs more framing and bracing.
  • Size: deck area, total area of all decks, patios and pergolas, and the distance from boundaries all affect approval; the exempt maximum is 25 m² each.
  • Access: narrow side access, stairs to the backyard and no space for cutting add labour hours, particularly on terraces in the Inner West.
  • Extras: balustrades, stairs, lighting, benches and roofing are priced separately and can add a great deal.
  • Older homes: if the deck attaches to a pre-1990 wall or eave, identify suspect asbestos-containing material before anyone drills or cuts.

DIY vs hiring a pro to build a deck

You save labour only on tasks you can do safely and legally, so match the job to your skills.

DIY or a handymanBook a licensed builder or trade
Small ground-level deck within the exempt limits, built to the maker’s instructionsAny building work valued at more than $5,000: licensed by Building Commission NSW
Replace or re-fix boards on a sound frameFootings, bearers and fixings to the house, which are structural
Oil, clean or sand the finished deckDecks higher than 1 m above ground, or larger than 25 m²
Fit decking screws, edges and trim neatlyPower for outdoor lights: book a licensed electrician
Check limits on the NSW Planning Portal and with councilOutdoor taps or showers: book a licensed plumber
Assemble flat-pack outdoor furniture afterwardsAnything that needs drilling into suspect pre-1990 sheeting

How to save when you build a deck without cutting corners

  1. Keep the deck at ground level where you can, because height adds framing, bracing and often approval work.
  2. Choose treated pine or a mid-range hardwood unless you specifically want composite, and compare maintenance as well as price.
  3. Keep the footprint to a clean rectangle that suits standard board lengths, which cuts waste and labour.
  4. Get at least three itemised quotes from licensed builders and compare scope, materials and exclusions line by line.
  5. Bundle small handyman tasks into a single visit: a Sydney half-day (4 hours) costs $230–$645 (typical $415), against a call-out of $92–$170.
  6. Pay no more than the 10% maximum deposit, and insist on a written contract: a small jobs contract under $20,000, or a full contract over $20,000.

What a fair deck quote should include

  • Itemised materials, including timber species or board brand, joists, bearers, footings and fixings, with quantities.
  • Access, scaffold or hoisting costs, and a line for removal of any old decking and waste.
  • Council or certifier fees if the deck is not exempt, plus any engineer’s drawings required.
  • The builder’s licence number, which you can check with Building Commission NSW, and Home Building Compensation cover above $20,000.
  • A staged payment schedule, with a deposit no higher than 10% before work starts.
  • Workmanship warranty in writing, kept separate from the material manufacturer’s terms, which you should read in full.

FAQ: deck building cost

How much to build a deck per square metre?

Roughly $250–$900 installed, depending on material, height and site (indicative — get itemised quotes). Ground-level treated pine sits at the low end, composite and raised hardwood at the top. Ask whether the quote includes stairs, balustrades and removal of old decking before comparing figures.

How much does it cost to build a deck?

A 20 m² ground-level deck commonly costs about $5,000–$18,000 depending on material (indicative — get itemised quotes). Anything valued over $5,000 must be built by someone licensed by Building Commission NSW, so budget for a licensed builder rather than relying on a casual quote.

How much does a deck cost compared with a patio?

The two are similar per m² when built from the same materials, because both need footings, framing and a surface. Patios and pergolas share the same exempt limits as decks, including 25 m² each, so confirm the totals with council before you build.

How much to build a deck in a rental or strata home?

The cost is the same, but approvals are not: renters need the owner’s written consent, and strata owners usually need committee approval on top of any council step. Get those consents in writing before you pay a deposit.

How much to build a deck in Australia if I do it myself?

You save the labour share, which in our price table is roughly half the total. You still pay for materials, tools and waste, and your deck must meet the exempt limits or approval rules. Over $5,000 in value, a licensed builder is required.

Getting your deck built in Sydney

If you want a deck priced properly, we can inspect the site, repair or re-board an existing frame and flag where a licensed builder is required. Book a Sydney handyman for decks and small jobs, and see our concrete driveway cost, retaining wall cost, retaining wall building, fence and gate repair, paving and raised garden bed guides for the surrounding yard.