Epoxy Flooring Cost in Sydney (2026 Guide)

Epoxy flooring cost for a Sydney home typically runs from about $40 to $150 per m² installed (indicative — get itemised quotes), with a DIY kit at the bottom and a ground, repaired and multi-coat system at the top. Slab condition, floor area, the type of system and how much prep the concrete needs drive the price more than the colour you choose.

This guide breaks down residential epoxy flooring cost by job type, city and DIY versus professional, with a quote checklist. If you are comparing surfaces, our carpet replacement cost guide shows the other end of the flooring budget.

Key points

  • Range: roughly $40–$150 per m² installed (indicative — get itemised quotes), depending on prep, system and finish.
  • Biggest cost driver: preparing the slab, because cracks, oil stains, old paint and moisture all have to be dealt with before coating.
  • Cheapest option: a DIY epoxy floor kit on a clean, sound garage slab, if you accept a thinner, less durable finish.
  • DIY is fine for a small, sound slab; hire a pro for large areas, damaged concrete or any floor in a pre-1990 home with unknown coverings.

Epoxy flooring cost: price table

These figures are a guide to what Sydney homeowners can expect to see in quotes, and they vary a lot between suppliers.

JobMaterialsLabourTotal
DIY epoxy floor kit, single garage slab$300–$900 (indicative)Your own time$300–$900 (indicative)
Professional coating, single garage, sound slab$600–$1,500 (indicative)$800–$2,000 (indicative)$1,500–$3,500 (indicative)
Professional coating, double garage$1,200–$3,000 (indicative)$1,500–$3,500 (indicative)$2,700–$6,500 (indicative)
Internal living area or patio, per m²$20–$60 (indicative)$30–$90 (indicative)$50–$150 (indicative)
Grinding, crack repair and moisture treatment extra$5–$25 per m² (indicative)$10–$40 per m² (indicative)$15–$65 per m² (indicative)
  • Treat every figure above as indicative — get itemised quotes, since slab condition changes the price more than area.
  • A basic sealed garage is cheaper than a flake or metallic system, which needs more coats and more skilled finishing.
  • Job value above $5,000 means the contractor must hold a Building Commission NSW licence if the work counts as residential building work.

Epoxy floors cost by city

Sydney labour rates sit above most other capitals, and the verified handyman rates below show how far prices can move between cities.

CityEpoxy per m², installedHandyman hourly rate (verified)
Sydney$60–$150 (indicative)$57–$140, typical $105
Melbourne$55–$140 (indicative)$52–$125, typical $94
Brisbane$50–$130 (indicative)Not in our data
Perth$50–$135 (indicative)Not in our data
Adelaide$45–$125 (indicative)Not in our data
  • City ranges for epoxy are indicative — get itemised quotes, as most suppliers price by job rather than a published rate.
  • Regional and outer-suburb jobs often cost more because crews travel with grinders, dust extraction and mixing gear.

What affects residential epoxy flooring cost

Two garages of the same size can differ by a few thousand dollars, and these are the reasons.

  • Slab condition: old oil stains, cracks and pitted concrete add grinding and patching time, which can double the prep portion of the quote (indicative).
  • Floor area: larger floors cost less per m² because set-up and travel are spread over more area.
  • System type: a clear or solid-colour coat costs less than a flake, quartz or metallic system with extra layers and a topcoat.
  • Moisture in the slab: a moisture test and sealer add cost, but skipping them is the main reason epoxy bubbles and peels.
  • Access and clearing: moving cars, shelving and stored goods takes time and some crews charge for it.
  • Removing an old coating or paint: grinding off a tired previous coat takes longer than grinding bare concrete.
  • Slip resistance: extra grit or an anti-slip additive suits a wet area or a sloping driveway, and adds a little to the price.

DIY epoxy flooring vs hiring a pro

A garage slab in good condition is a sensible DIY project, but the preparation is hard, dusty work.

FactorDIY epoxy floor kitProfessional epoxy flooring
CostLowest upfront; you buy the kit and hire or buy a grinderHigher, with prep, materials and labour itemised
PrepAcid etching or a hired grinder; heavy dust, so follow the label for protective gearCommercial diamond grinding with dust extraction
FinishThinner coat; roller marks and fisheyes are common on stained concreteSmoother, thicker and better bonded
DurabilityCan lift under hot tyres if the slab is damp or poorly preparedBetter chance of lasting when the slab is tested and treated
WarrantyProduct warranty only, and only if you follow the instructionsWorkmanship warranty, ask for it in writing
Best forSmall, sound slabs and shedsLarge floors, internal areas and damaged concrete
  • Follow the product label and safety data sheet for mixing, ventilation, working time and curing; never improvise with solvents or thinners.
  • Do not grind or sand a floor in a house built before 1990 until you know what is underneath, because floor coverings and adhesives may contain asbestos (see asbestos.nsw.gov.au).

How to save on epoxy flooring cost without cutting corners

  1. Clear the slab yourself before the crew arrives, including shelving and oil stained rags, so you are not paying for labour on moving stuff.
  2. Get at least three itemised quotes and compare the same scope, because one cheap price may leave out grinding or crack repair.
  3. Choose a solid colour or simple flake instead of metallic effects, which need more coats and a skilled finisher.
  4. Coat the garage first and leave a patio or workshop for later, so you can judge how the floor performs.
  5. Repair small cracks and fill chips only as the product instructions allow, and leave structural cracks to a professional.
  6. Book the job in drier months, since damp slabs and cold mornings extend cure times and risk a failed bond.

What a fair epoxy flooring quote should include

A fair quote lists each item, so you can compare two prices without guessing what is missing.

  • Itemised materials: the system name, number of coats and topcoat, with the product data sheet attached.
  • Surface prep: diamond grinding or shot blasting, crack repair, moisture test and the sealer if the slab needs it.
  • Access and clearing: who moves vehicles and stored items, and any charge for it.
  • Waste removal: who takes away dust, old coating and empty containers.
  • Warranty: a workmanship warranty in writing, plus the product warranty terms from the maker.
  • Licence and contract: a Building Commission NSW licence number for residential building work over $5,000, and a written contract; work under $20,000 uses a small jobs contract and the maximum deposit is 10%.

FAQ: epoxy flooring cost

How much does epoxy flooring cost in Australia?

Installed epoxy flooring typically costs about $40 to $150 per m² (indicative — get itemised quotes), with a double garage often landing between $2,700 and $6,500 (indicative). Slab condition, system type and prep decide where you land. A DIY kit is the cheapest route for a small, sound slab.

How much epoxy flooring cost should I budget for a single garage?

Plan for roughly $1,500 to $3,500 for a professional single-garage coating on a sound slab (indicative — get itemised quotes), or $300 to $900 for a DIY kit. Add more if the slab needs grinding, crack repair or a moisture treatment before coating.

Is a DIY epoxy floor kit worth it?

A kit can work on a small, dry, clean slab if you follow the label exactly. The risk is poor prep, which causes lifting and peeling. If the slab is stained, cracked or damp, a professional system usually lasts longer and costs less than redoing a failed floor.

Can I epoxy a floor in a rental?

Ask the owner in writing first, because a coating is permanent and is not one of the minor changes NSW tenants can request as of right. If the answer is no, consider a removable mat or tiles instead.

Does epoxy flooring need a licensed tradesperson?

Epoxy is not specialist electrical or plumbing work, but residential building work valued at more than $5,000 must be done by someone licensed by Building Commission NSW. Ask for the licence number and a written contract before any work starts.

Getting epoxy flooring cost under control in Sydney

If you would rather not hire a grinder and risk a failed coat, we can inspect the slab, advise on prep and coordinate the job. Book a Sydney handyman for small floor repairs and quotes. Related reading: timber flooring cost, floor sanding cost, polished concrete floors cost and self-levelling floor compound.