How to measure for blinds: decide on an inside or outside mount, measure the width and drop with a steel tape in three places, record the smallest inside measurement or the largest outside one, and write it down as width by drop. The most common failure is mixing up the two mounts, because a blind that is a few millimetres too wide simply won’t fit.
This guide covers how to measure for blinds step by step, how to measure a window for curtains, the tools you need, and what a handyman charges in Sydney if you’d rather have it measured and installed for you.
Key points
- Plan on eight steps and one pass of checks per window, and always measure each window separately because Sydney windows are rarely the same size.
- A steel tape measure is the one tool you can’t skip, since cloth and plastic tapes stretch and give you a size that won’t fit.
- Use a second person for tall windows and curtain tracks above shoulder height, and never climb a chair or the arm of a sofa.
- A Sydney handyman typically charges about $125 per visit for small fixing jobs like hanging (range $80–$205, October 2026), with a minimum charge of about $140.
How to measure for blinds: can you DIY it?
Measuring is a safe DIY job for almost everyone, because all you need is a tape, a pencil and patience.
| Your situation | DIY OK? | Why |
|---|---|---|
| Standard window with a deep reveal | Yes | An inside mount is simple when the recess is deep and square enough for the blind. |
| Shallow reveal or uneven frame | Yes, carefully | An outside mount hides gaps, but you must allow enough overlap each side to block the light. |
| Tall window or sliding door | With a helper | A long steel tape needs two people to hold it straight, and a ladder needs someone at the base. |
| Curved, arched or bay window | Ask a pro | The angles and joins need accurate templates, and a wrong size is expensive to re-order. |
| You’re renting | Ask first | NSW lets tenants ask for internal curtains or removable blinds, but you must get consent before fitting. |
| Home built or renovated before 1990 | Check first | Don’t drill or sand old window linings or eaves until you have checked the NSW asbestos guidance. |
| Motorised blinds needing power | Measure yes, wiring no | A new power point or wiring is work for a licensed electrician in NSW. |
Tools for measuring a window for blinds
| Item | What it’s for | Tip |
|---|---|---|
| Steel tape measure | Gives an accurate width and drop | Read the same edge of the tape each time and measure to the nearest millimetre. |
| Pencil and notepad | Records each measurement | Write width first, then drop, and label each window by room. |
| Spirit level | Checks the window and the head are level | A sloping head means the blind may sit crooked, so note it for the installer. |
| Step ladder | Reaches the top of tall windows | Use one with a second person holding it, never a chair or table. |
| Phone camera | Records the window and any obstacles | Photograph handles, cranks, sills and the cord position before you order. |
| Supplier measure guide | Gives product-specific allowances | Check the maker’s guide and instructions, since each blind type has its own rules. |
How to measure for blinds: step by step
Do this with the window frame clear of furniture, and complete every step for each window.
- Decide whether you want an inside mount in the recess or an outside mount on the wall or frame, because the method differs for each.
- Check the recess depth against the blind’s minimum depth in the maker’s guide, and look for handles or cranks that could foul the blind.
- For an inside mount, measure the width at the top, middle and bottom of the recess with a steel tape, then use the narrowest result.
- Measure the drop at the left, centre and right of the recess, and use the longest result if the blind should sit just above the sill.
- For an outside mount, measure the window width, then add an overlap each side so the blind covers the frame and blocks the light.
- For the outside drop, measure from where the blind will sit above the frame to where you want it to finish, such as the sill or floor.
- Write every size as width by drop, note the mount type and room, and take a photo of the window for reference.
- Re-measure each window the next day, compare the figures with the maker’s ordering sheet, and order only when both measurements match.
How to measure window for curtains
Curtains give you more freedom than blinds, but the track or rod position drives every number. Our curtain rod installation guide covers fixing it.
- Fix the rod or track position first, because curtain length and width are measured from where it will actually hang.
- Measure the track or rod width, then add a little each side so the curtains stack clear of the glass when open.
- Choose a fullness from the maker’s guide, since fabric needs extra width to look gathered rather than stretched flat.
- Measure the drop from the rod or track down to the sill, below the sill, or to just above the floor.
- Allow for the hem and heading style, and for rings or hooks, as the curtain maker’s guide specifies.
- Mark the position with painter’s tape on the wall first, then step back and check it looks right from the room.
Measuring for inside and outside mount blinds
The mount type changes which edge of the window you trust, and older Sydney homes often have frames out of square.
- Choose an inside mount for a clean look when the recess is deep enough, square and free of handles or cranks.
- Choose an outside mount for shallow recesses, uneven frames or when you want to block more light at the edges.
- Use the smallest width for an inside mount, because the blind must pass the tightest point of the recess.
- Use extra overlap for an outside mount on wide windows, and check the maker’s guide for the product’s allowance.
- Check roller, Roman, venetian and vertical blinds against their own measuring guides in our types of blinds guide.
- Read our roller blind installation guide and outdoor blinds guide before ordering, since fitting and sizing differ.
Common mistakes when you measure for blinds
- Using a cloth or plastic tape that stretches, which gives a figure that is out by more than the blind’s tolerance.
- Measuring one point only, then finding the window is narrower at the top, middle or bottom of the recess.
- Mixing up the inside and outside mount rules, so the blind is too wide for the recess or too narrow to cover the frame.
- Ignoring handles, cranks, sills and cords, which can stop the blind or curtain from moving freely.
- Drilling the brackets into old window linings or eaves in a pre-1990 home without checking for asbestos first.
- Climbing a chair to reach a tall window instead of using a proper ladder and a second person.
When to call a handyman to measure for blinds (or a licensed trade)
- The window is large, curved, arched or part of a bay, and one wrong size means an expensive re-order.
- You are measuring several rooms and want one visit to measure, order advice and install.
- The frame is out of square, the reveal is shallow or the window sits high above the floor.
- The wall is brick, tile or rendered, where brackets and anchors need the right bits and fixings; see our curtain installation cost guide.
- You want motorised blinds with a new power supply, which needs a licensed electrician such as TQN Electrician.
- The home is pre-1990 and you are unsure about asbestos in the window linings or eaves.
Cost to hire a handyman for measuring and blinds in Sydney
Prices include GST and come from October 2026 Sydney handyman data. See our blinds cost guide for the price of the blinds themselves.
| Job | Low | Typical | High |
|---|---|---|---|
| Small fixing job, such as picture or shelf hanging (per visit) | $80 | $125 | $205 |
| Handyman hourly rate, Sydney | $57 | $105 | $140 |
| Call-out or minimum charge, Sydney | $92 | $140 | $170 |
| Half-day handyman, Sydney (4 hours) | $230 | $415 | $645 |
| Full-day handyman, Sydney (8 hours) | $435 | $690 | $1,025 |
- The small-job row is a comparable guide only, because there is no fixed rate for measuring a window in the data.
- Ask whether a measuring visit is free or charged if you order the blinds through the same supplier.
- Bundle blind installation with other small jobs, like replacing vertical blind slats, to share the minimum charge.
FAQ: how to measure for blinds
How to measure for blinds in an inside mount?
Measure the width at the top, middle and bottom of the recess with a steel tape and use the narrowest figure. Measure the drop at the left, centre and right, then check the recess depth against the blind’s minimum. Write the result as width by drop and follow the maker’s guide.
How to measure window for curtains?
Fix the rod or track position first, then measure its width and add a little each side for stacking. Measure the drop from the rod or track to the sill, below it, or just above the floor. Check the fabric’s fullness and hem allowances in the maker’s guide.
Should I measure inside or outside the window frame?
Measure inside for a neat recessed look if the window is deep and square. Measure outside the frame for a shallow recess, an uneven frame or more light control. The mount type changes which edge you measure, so decide before you pick up the tape.
Can renters put up curtains and blinds?
In NSW a landlord cannot unreasonably refuse internal curtains or removable blinds, but you must ask first, and the tenant pays unless agreed otherwise. Strata and heritage homes have extra limits. Get the consent in writing before you buy or drill any holes.
Getting your windows measured and fitted in Sydney
If you’d rather not work out how to measure for blinds across every room, we can measure, advise on mounts and install them level. Book a handyman in Sydney and have curtains, rods and blinds sorted in one visit.


