How to Silicone Shower: Step-by-Step Guide

How to silicone a shower: remove the old silicone, clean and dry every joint, tape both edges, run a steady bead of bathroom silicone with a caulking gun, smooth it, and peel the tape off while the silicone is still wet. The most common failure is sealing over damp or dirty joints, which makes the new bead peel and the mould return.

This guide covers how to silicone a shower step by step, how to apply silicone sealant on tiles, whether you can silicone over silicone, what caulk is, and what a Sydney handyman charges.

Key points

  • Siliconing a shower is a moderate DIY job of nine steps; the neat finish comes from preparation and taping, not from a fancy gun.
  • A clean, dry joint is the one thing you can’t skip, because silicone won’t bond to soap scum, moisture or old residue.
  • Ventilate the room, wear gloves, and check the cartridge label for curing and use instructions, because the maker’s directions decide when the shower is ready.
  • A Sydney handyman typically charges about $205 to reseal a joint (range $115–$345, October 2026), and a leaking shower needs a licensed plumber first.

Can you silicone a shower yourself?

Most people can reseal a shower in an afternoon. Use this table to check your situation first.

Your situationDIY OK?Why
Cracked or mouldy bead at the cornersYesCutting out the old bead and resealing is straightforward with the right prep.
Gap between tiles and the bath or trayYesThis joint moves, so it needs flexible silicone rather than grout, and it is easy to reach.
Shower screen edgesYes, with careThe seal needs a clean, dry frame, and a heavy glass screen is easier with a second person.
Gaps wider than a normal jointCheck firstWide gaps may need a backing rod or a repair first, so follow the sealant’s instructions.
Pre-1990 home with old wet-area liningsCheck firstWet-area linings and floor coverings in older homes may contain asbestos, so identify suspect material before you scrape or cut.
Leaking shower or damp wallNoWaterproofing and leaks are licensed plumbing work, so book a licensed plumber or waterproofer first.
You’re rentingAsk firstTell your landlord before resealing, and agree who pays for materials and the work.

Tools and materials to silicone a shower

ItemWhat it’s forTip
Bathroom or sanitary siliconeSeals the wet jointsBuy a mould-resistant silicone made for wet areas from brands like Selleys, Sika or Bostik, and check the label.
Caulking gunPushes the silicone out evenlyA smooth-action gun gives a steadier bead than a cheap ratchet type.
Utility knife and plastic scraperRemoves the old beadOur guide to removing silicone shows how to leave a clean joint.
Masking tapeKeeps the edges neatPress the tape down firmly along both sides, leaving a clear gap for the bead.
Smoothing toolShapes the bead into the jointUse the tool or method the cartridge instructions allow, and wipe the tool between passes.
Cleaner, cloths and glovesPreps the joint and protects handsUse a cleaner suited to bathroom surfaces and let the joint dry fully before you start.
Fan or open windowMoves fumes and speeds dryingVentilate the room throughout, and keep children and pets out until the job is done.

How to silicone a shower: step by step

Allow time for the joints to dry first, because that is the part that most people rush.

  1. Cut out all the old silicone and clear every trace of residue, as covered in our guide, then check the grout beside it is sound.
  2. Clean the joint with a bathroom cleaner suited to the surface, rinse it, and dry it thoroughly with a cloth before you do anything else.
  3. Check the tiles, tray and wall are fully dry, using a fan if needed, because trapped moisture stops the bead from bonding.
  4. Run masking tape along both sides of the joint, leaving a neat gap for the bead, and press it down along its full length.
  5. Cut the cartridge nozzle at an angle to suit the joint width, and puncture the inner seal as the instructions describe.
  6. Squeeze a steady bead along the joint, moving at an even pace, and push the silicone into the gap rather than laying it on top.
  7. Smooth the bead in one continuous pass using the method the maker allows, and wipe the excess off the tool as you go.
  8. Peel the masking tape away while the silicone is still wet, pulling it back on itself and away from the bead.
  9. Leave the joint untouched and dry for the time on the cartridge, and read how long silicone takes to dry before you use the shower.

How to apply silicone sealant on tiles

Tile joints behave differently depending on where they sit. Flat tile-to-tile joints take grout, and corners and edges take silicone.

  • Use silicone only where two surfaces meet or the joint moves, such as corners, the bath edge and the tray, and use grout elsewhere.
  • Match the silicone colour to the grout, and see our grout types and colours guide before you buy.
  • Tape the tile edge as well as the wall edge, so the bead is crisp on both sides.
  • Check the label if you have natural stone tiles, because some silicones can stain porous stone.
  • Fix cracked grout before you silicone beside it, using our how to grout tiles guide or shower regrouting guide.

Can you silicone over silicone?

You shouldn’t. New silicone doesn’t bond reliably to old silicone, so the fresh bead peels off at the edges within weeks.

  • Cut out the old bead completely, then remove the thin residue film that remains on the tile and frame.
  • Patching one small section by overlapping it onto the old bead usually shows a join and fails first at that point.
  • Clean the bare joint, let it dry, then lay the new bead in one continuous run from end to end.
  • Test the joint by pressing a fingertip along it, and feel for any slick, oily patches before you tape.
  • Switch to epoxy grout for flat tile joints if you want a harder wearing finish, as explained in our epoxy grout guide.

What is caulk, and how to caulk like a pro

Caulk is a flexible sealant that fills gaps, and in Australia the word covers silicone and acrylic gap fillers. Silicone suits wet areas, while acrylic suits dry gaps you can paint.

  • Use silicone in the shower, bath and basin joints, because acrylic caulk isn’t designed to cope with constant water and moulds sooner.
  • Cut the nozzle small, then enlarge it if needed, because a bead that is too big is harder to tool neatly.
  • Squeeze at a steady pace with a constant angle, and keep the bead slightly ahead of the nozzle for a smooth, continuous line.
  • Smooth every joint within the working time on the cartridge, and don’t go back over a bead that has started to skin.
  • Keep a damp cloth and a bin bag handy, and wipe tools after every joint so you never smear silicone onto the tile.

Choosing silicone for the bathroom

Sealant typeBest forWatch out for
Sanitary or bathroom siliconeShower corners, bath edges, basins and screensCannot be painted, and needs a clean, dry joint to bond.
General-purpose siliconeWindows and non-wet jointsCheck the label, because it may not resist mould in constant wet.
Acrylic gap filler (caulk)Dry gaps around skirting and architraves that will be paintedNot suited to wet areas such as showers.
Neutral-cure siliconeNatural stone, metals and some plasticsCheck the label for compatible surfaces before you buy.
Epoxy groutFlat tile joints in wet areasHard to fix once set, and not for moving corner joints.

Common mistakes when you silicone a shower

  • Sealing over damp, dirty or soap-scummed joints, so the bead fails to bond and peels within weeks.
  • Laying silicone over old silicone instead of cutting it out first and removing the residue film.
  • Using the wrong product, such as painter’s acrylic caulk, in a wet area where it moulds and splits.
  • Smoothing too late, after the silicone has skinned, which leaves a lumpy, torn surface that traps dirt.
  • Scraping or cutting wet-area linings in a pre-1990 home without checking for asbestos first.
  • Using the shower too soon, instead of following the cartridge instructions, and wiping the bead off or breaking its seal.

When to call a handyman to silicone a shower (or a licensed trade)

  • The shower leaks, the wall is damp or the tiles sound hollow, which points to waterproofing failure; book a licensed plumber such as TQN Plumber.
  • The joints are very wide, deeply stained with mould or full of old residue that you can’t remove cleanly.
  • The bathroom is in a home built or renovated before 1990 and you are unsure about the lining behind the tiles.
  • The screen is heavy frameless glass, which needs a second person and careful handling to avoid chips.
  • You want grout repairs, silicone and a deep clean done together, ready for an inspection or sale. See how to clean grout in the meantime.
  • You’re short on time and want the job done neatly in a single visit.

Cost to hire a handyman to silicone a shower in Sydney

Prices below include GST and come from October 2026 Sydney data. Siliconing is usually quoted as part of a resealing job.

JobLowTypicalHigh
Weatherproofing or resealing with silicone, Sydney (per job)$115$205$345
Handyman hourly rate, Sydney$57$105$140
Call-out or minimum charge, Sydney$92$140$170
Half-day handyman, Sydney (4 hours)$230$415$645
Full-day handyman, Sydney (8 hours)$435$690$1025
  • Ask whether the quote includes cutting out the old silicone, cleaning the joints and the new sealant.
  • Book other small bathroom jobs in the same visit, so the minimum charge covers all of them.

FAQ: how to silicone a shower

How to silicone a shower for the first time?

Cut out the old bead, clean and dry every joint, and tape both edges. Run a steady bead of bathroom silicone, smooth it in one pass, and peel the tape off while it is wet. Follow the cartridge instructions before you use the shower.

How to apply silicone sealant neatly?

Tape the joint, cut the nozzle at an angle, and push the silicone into the gap at a steady pace. Smooth within the working time, then remove the tape while the bead is still wet. Keep a cloth handy to wipe tools between joints.

How to caulk a bathroom like a pro?

Prepare the joint properly, use silicone for wet areas, and keep the nozzle small and the angle constant. Work in short runs, smooth each joint quickly and wipe tools often. Good preparation and taping do more for the finish than technique alone.

What is caulk, and is it the same as silicone?

Caulk is any flexible sealant that fills gaps. Silicone is one type and suits wet areas, while acrylic caulk suits dry gaps that will be painted. Check the label for the area you are sealing, and choose a bathroom silicone for showers.

Getting your shower siliconed in Sydney

If you’d rather not work out how to silicone a shower yourself, we can strip the old bead, prepare the joints and reseal them in one visit. Read the epoxy grout guide if you are weighing up a full regrout, or book shower resealing in Sydney and add any other small jobs.