How to regrout shower tiles: rake out the old grout with a grout removal blade, vacuum the joints, mix fresh grout to the maker’s instructions, pack it in with a rubber float, wipe the haze, then seal once it has cured. The step that goes wrong most often is grouting over a damp wall or a failed waterproof membrane, which traps moisture and brings the mould straight back.
This guide covers how to regrout a shower step by step, how to remove grout from tiles safely, which products to buy, and what a Sydney handyman charges to do it for you.
Key points
- Regrouting a shower is a patient job of about ten steps, and most of the effort goes into removing the old grout cleanly rather than applying the new.
- A grout removal blade or oscillating tool with a grout blade is the one tool you can’t skip, because a wandering blade chips tile edges.
- Check for asbestos in pre-1990 homes and for cracked tiles or a damp wall before you start; both stop a DIY job.
- A Sydney handyman charges about $140 as a typical call-out, around $105 an hour, and resealing work typically comes to about $205 (Oct 2026).
How to regrout shower tiles: can you DIY it?
Most people with patience and a steady hand can regrout a small shower over a weekend. Use this table to check your situation first.
| Your situation | DIY OK? | Why |
|---|---|---|
| Cracked or crumbling grout, tiles still firm | Yes | This is the standard regrout job, and fresh grout restores the seal between the tiles. |
| Black mould that returns after cleaning | Yes, with a check | Test for damp behind the wall first, because new grout can’t fix a leak or poor ventilation. |
| Loose, drummy or cracked tiles | No | Hollow-sounding tiles need relaying, and new grout over them will crack again within weeks. |
| Grout is failing and water is staining the ceiling or room below | No | The waterproofing may have failed, which is work for a licensed waterproofer or plumber. |
| Bathroom in a home built or renovated before 1990 | Check first | Wet-area linings may contain asbestos, so don’t grind, drill or scrape until you’ve identified the material. |
| You’re renting | Ask the landlord first | Grout is part of the fixtures, so get written consent and agree who pays before you touch it. |
| Cracked silicone along corners and the shower base | Yes | Corners and changes of plane need flexible sealant, not rigid grout, and our guide to how to silicone a shower covers that step. |
Tools and materials to regrout a shower
| Item | What it’s for | Tip |
|---|---|---|
| Grout removal blade | Rakes old grout out of the joints | Pick a carbide-tipped hand blade for small areas, and keep it central in the joint so it doesn’t bite the tile edge. |
| Oscillating multi-tool with grout blade | Speeds up long joints on big walls | Brands like Ryobi and Makita sell these; run it slowly and wear a dust mask and safety glasses. |
| Vacuum or shop vac | Clears dust and fragments from the joints | Vacuum twice, because leftover dust stops the new grout from bonding. |
| Grout, powder or pre-mixed | Fills the joints | Ardex and Mapei grouts are stocked at Bunnings; match the type to the joint width and read the packet. |
| Rubber grout float | Packs grout into the joints | Hold it at an angle and work across the joints diagonally so you don’t drag grout out again. |
| Sponge and clean buckets | Wipes excess grout and haze | Change the water often and wring the sponge nearly dry so you don’t wash grout out of the joints. |
| Grout sealer | Helps cement-based grout resist stains | Check whether your grout needs sealing; epoxy and some pre-mixed grouts don’t, so follow the maker’s label. |
| Masking tape and silicone | Protects tile faces and seals corners | Tape the shower base edge and corner joints so they stay free for flexible sealant. |
How to regrout a shower: step by step
Block out a full day, because the grout needs time to firm up between steps. Always follow the manufacturer’s instructions on the packet for mixing and curing times.
- Clean the tiles and grout lines with a bathroom cleaner, rinse, and let the wall dry fully so you can see where the grout is really cracked.
- Press a screwdriver tip along the joints and tap each tile, and stop if tiles sound hollow, move, or the wall feels soft or damp.
- Rake out the old grout with the removal blade, working along each joint and removing about two-thirds of its depth so the new grout has something to grip.
- Keep the blade centred and use short strokes near tile corners, because a slipped blade chips glaze and leaves a mark you can’t hide.
- Vacuum every joint, wipe with a barely damp sponge, and let the surface dry; dust left in the joint is the usual cause of crumbling new grout.
- Mix the grout in small batches following the packet, then let it rest for the time stated so the additives activate before you use it.
- Press grout into the joints with the float held at an angle, working diagonally and filling the joints fully so no air pockets remain.
- Scrape off the excess at a sharp angle, then wait for the time on the packet before the first light wipe with a damp, well-wrung sponge.
- Buff the haze off the tile faces with a dry cloth once it forms, and leave the shower unused for the cure time on the packet.
- Seal the grout if the maker says it needs it, then flex-seal the corners and base with silicone once the grout has cured.
How to remove grout from tiles
If you want to know how to remove grout without wrecking the tile, patience with the blade is the answer. Older Sydney bathrooms with soft, sandy grout come out easily, while epoxy is far harder.
- Use a hand grout removal blade on narrow joints, because it gives you the most control and the least risk of chipping.
- Switch to an oscillating tool only for long straight runs, and finish the corners and ends by hand with the blade.
- Score down both sides of the joint first, then lift out the centre, which stops the blade skidding onto the tile edge.
- Tape the shower base and any metal trims so a slip doesn’t scratch them, and keep the water off while you work.
- Epoxy grout resists most blades, so read our epoxy grout guide before you decide whether to tackle it yourself.
- Wear a dust mask and eye protection, and stop at once if you suspect asbestos in an old wet-area lining.
Regrouting without removing the old grout
People often ask about regrouting a tiled floor without removing old grout, and the honest answer is that it is only a patch, not a proper fix.
- Grout-over products and colour-restoring paints can freshen sound grout, but they won’t repair cracks or stop leaks.
- Skipping removal works only on stable, firm grout with surface staining, never on joints that crumble or have gaps.
- New grout laid on a thin film of old grout bonds poorly and tends to flake off within months.
- For a floor or shower wall that gets wet daily, rake out the failed lengths and regrout those properly.
- If the only issue is stains, try the methods in our guide to cleaning grout before you remove anything.
- If the joints are wide or uneven, our how to grout tiles guide covers filling them properly.
Choosing the right shower grout at Bunnings
The grout aisle at Bunnings can look overwhelming, but most shower jobs come down to three choices.
| Grout type | Best for | Watch out for |
|---|---|---|
| Cement-based powder (such as Ardex or Mapei) | Most standard shower walls and floors | Needs correct mixing and usually benefits from sealing; check the packet. |
| Pre-mixed grout | Small repairs and first-time DIYers | Check it is rated for wet areas and read the cure time on the tub. |
| Epoxy grout | Showers where mould and stains are a constant problem | Short working time and hard to remove later; see the grout types and colours guide. |
| Flexible sealant (silicone) | Corners, the shower base and changes of plane | Not a substitute for grout in flat tile joints; allow the full drying time from the silicone drying guide. |
Common mistakes when you regrout a shower
- Leaving about half the old grout in the joint, which leaves too little depth for the new grout to grip.
- Skipping the damp and tile check, then grouting over drummy tiles or a wall that is still leaking behind the surface.
- Using rigid grout in internal corners and at the shower base, where movement splits it and silicone should be used instead.
- Wiping too early or with a wet sponge, which pulls grout from the joint and leaves pinholes.
- Showering before the grout has cured, which softens the surface and stains it unevenly.
- Ignoring asbestos risk in homes built or renovated before 1990 before you scrape or grind near old wall linings.
When to call a handyman to regrout your shower (or a licensed trade)
- The tiles are loose, hollow or cracked, and need relaying before any new grout will last.
- Water stains show on the ceiling below or the wall outside the shower, which suggests failed waterproofing; book a licensed plumber, such as TQN Plumber, for waterproofing and leaks.
- The bathroom was built or renovated before 1990 and you can’t rule out asbestos in the lining or adhesive.
- You need to remove old silicone first, and want the corners redone neatly; see our guide to removing silicone.
- You’re renting and want the work done cleanly, with the landlord’s written consent in place.
- You don’t have a full day free, or you’ve already tried and the grout lines are uneven.
Shower regrout cost in Sydney
Quoted prices include GST and come from October 2026 Sydney handyman data. The cost to regrout a shower depends on tile size, joint length, the old grout and whether tiles need replacing.
| Job | Low | Typical | High |
|---|---|---|---|
| Handyman hourly rate, Sydney | $57 | $105 | $140 |
| Call-out or minimum charge, Sydney | $92 | $140 | $170 |
| Half-day handyman, Sydney (4 hours) | $230 | $415 | $645 |
| Full-day handyman, Sydney (8 hours) | $435 | $690 | $1,025 |
| Weatherproofing or resealing, Sydney (per job) | $115 | $205 | $345 |
- A full shower regrout often takes a half to a full day of work, so expect a quote of roughly $400–$1,000 (indicative — get itemised quotes).
- A patch repair of a few failed joints can cost much less, often close to the call-out charge (indicative — get itemised quotes).
- Ask whether the quote covers grout, sealer, silicone, and rubbish removal, and whether the price changes if tiles need replacing.
- A full day can cost less than eight hourly-billed hours, so bundle small jobs such as cleaning grout or resealing into one visit.
FAQ: how to regrout shower tiles
How do you regrout a shower?
Rake out the old grout with a grout removal blade, vacuum the joints, then press in fresh grout with a rubber float. Wipe the haze off, let it cure for the time on the packet, then seal the grout if required and silicone the corners and base.
How do you remove grout from tiles?
Use a hand grout removal blade or an oscillating tool with a grout blade. Score along both sides of each joint, lift out the centre, and keep the blade away from the tile edge. Vacuum the joints clean before you apply any new grout.
How much does it cost to regrout a shower in Australia?
A Sydney handyman charges about $105 an hour, with a typical call-out of $140 and a half-day around $415 (October 2026). A full shower regrout usually falls in the half-day to full-day range (indicative — get itemised quotes), depending on tile size and condition.
Can you regrout bathroom tiles without removing the old grout?
Only as a cosmetic patch on firm, stained grout. Cracked or crumbling grout must be raked out first, or the new grout won’t bond and will fail within months. Corners and the shower base also need flexible silicone rather than rigid grout.
Getting your shower regrouted in Sydney
If you’d rather not spend a day on your knees with a blade, we can rake out, regrout and reseal your shower in one visit, and tell you early if the tiles or waterproofing need more than grout. Book shower regrouting in Sydney and add any other small bathroom repairs to the same visit.


