How to grout tiles: clear the joints, mix the grout to the packet instructions, press it in with a rubber float at an angle, wipe the surface clean, then let it cure before it gets wet. The most common failure is wiping too early or too hard, which pulls grout out of the joints and leaves pinholes.
This guide covers how to grout tiles step by step, plus the differences for floors, walls and showers, the mistakes that ruin a finish, and what a Sydney handyman charges if you would rather hand it over.
Key points
- Grouting is a moderate DIY job of nine steps; the work is simple, but you have to move quickly while the grout is workable and follow the packet’s timing.
- A rubber grout float and a clean sponge are the tools you can’t skip, because a trowel or a dry rag will scratch tiles and leave haze.
- Shower walls and floors in a home built or renovated before 1990 may sit over asbestos-containing linings, so check before you scrape or grind anything.
- A Sydney handyman typically charges about $140 for a minimum visit and $105 an hour (October 2026), so a small regrout often costs one call-out plus a couple of hours.
Can you grout tiles yourself?
Most people can grout a bathroom splashback or a small floor over a weekend. Use this table to check your situation first.
| Your situation | DIY OK? | Why |
|---|---|---|
| New wall tiles, cement-based grout | Yes | Cement grout is forgiving, stays workable for a while and cleans up with water and a sponge. |
| Floor tiles in a hallway or kitchen | Yes | Large flat areas suit a float, but you need a clear plan so you never kneel on wet grout. |
| Regrouting a shower | Yes, with care | Raking out old grout is slow, and damaged waterproofing behind it is the real risk. |
| Epoxy grout | Experienced DIYers only | Epoxy sets fast, sticks to everything and is hard to fix once it hardens. |
| Pre-1990 home with old wet-area linings | Check first | Wet-area linings and floor coverings in older homes may contain asbestos, so identify suspect material before you disturb it. |
| Cracked or drummy tiles | No, re-lay first | Grout cannot fix a tile that has lost its bond; the tile has to come up and be fixed properly. |
| Leaking shower or damp wall | No | Waterproofing is licensed trade territory, so book a licensed plumber or waterproofer before any regrouting. |
Tools and materials to grout tiles
| Item | What it’s for | Tip |
|---|---|---|
| Grout (cement-based or epoxy) | Fills the joints between tiles | Match the grout to the room and joint width, and read the packet for mixing ratio and working time. Brands like Mapei and Ardex list this clearly. |
| Rubber grout float | Pushes grout into the joints | Use a firm, fresh float; an old chipped edge leaves streaks and low spots. |
| Grout rake or oscillating tool | Removes old grout when regrouting | Keep the blade inside the joint so it does not chip the tile edges. |
| Two buckets and a grout sponge | Mixing water and rinse water | Change the rinse water often, because dirty water redeposits haze on the tile. |
| Spacers and masking tape | Protects edges and keeps joints even | Tape off the corners where silicone will go later, not grout. |
| Dust mask, glasses and gloves | Protects you from dust and alkaline grout | Cement grout irritates skin, so wear gloves and rinse splashes straight away. |
| Soft cloth and sealer | Final buff and protection | Only seal when the packet says the grout is ready, and use a sealer made for your grout type. |
How to grout tiles: step by step
Work in small sections so the grout never dries before you wipe it. A second pair of hands helps on large floors.
- Check that the tile adhesive has cured, clear every joint of dust and spacers, and vacuum the lines so the new grout has clean edges to grip.
- Tape off skirting, benchtops and any corner or change of plane where flexible silicone will go instead of grout, and protect the floor with drop sheets.
- Mix the grout in a clean bucket exactly as the packet says, adding the powder to the water slowly, and stir to a thick, lump-free paste.
- Leave the mix to rest if the packet asks you to, then restir briefly without adding extra water, which weakens the finished joint.
- Spread the grout over a small area with the float held at a steep angle, working diagonally across the joints to pack them fully.
- Scrape the excess off the tile faces with the float edge held almost upright, so the joints stay full but the surface is mostly clear.
- Wait for the grout to firm up as the packet describes, then wipe lightly in circles with a barely damp sponge, rinsing it after every pass.
- Check each joint for pinholes or low spots, fill them straight away, and keep wiping gently so you do not drag grout out of the lines.
- Buff the haze off with a dry soft cloth once the surface has dried, then keep the area dry and unused for the time the packet gives.
How to grout floor tiles
Floors take foot traffic and spills, so the grout choice matters as much as the technique. Our grout types and colours guide compares the options.
- Plan your exit route before you start, grouting from the far corner back to the door so you never stand on fresh work.
- Use a grout formulated for floors, and check the packet for the maximum joint width it suits before you mix a bucket.
- Press the float firmly across the joints in both directions, since floor joints are deeper and trap air if you skim them.
- Kneel on a board or foam mat rather than the tiles, and keep pets and kids out until the packet says it is safe to walk.
- Avoid mopping the floor during the curing period, and use only a damp cloth for the first clean afterwards.
How to grout wall tiles
Wall tiles are lighter work than floors, but the grout can slump in tall joints and stain easily. Work from the top down so drips land on unfinished tiles.
- Start at the top row and work down, so any grout that runs lands on the next section you have not wiped yet.
- Mix the grout slightly stiffer for vertical joints, within the packet’s water range, so it stays packed and does not slump.
- Take extra care around power points and switches, and turn the power off at the switchboard before you remove any cover plates.
- Leave a clean, grout-free gap at the bench, bath and corners, because those joints move and need flexible silicone, as our guide to silicone in a shower explains.
- Wipe splashbacks with the sponge held almost flat, because a loaded sponge on a vertical surface drips down and smears the finished lines.
How to grout shower tiles
Showers are the hardest place to grout, because the joints stay wet and the waterproofing sits behind them. In older Sydney bathrooms, tired grout is often the first sign of water getting behind the tiles.
- Rake out failed grout completely, rather than grouting over it, and read our shower regrouting guide before you start.
- Do not scrape or grind linings in a pre-1990 home until you have identified suspect material, and treat it as asbestos if you are unsure (asbestos.nsw.gov.au).
- Remove old silicone first with the method in our guide to removing silicone, then regrout the flat joints and resilicone the corners.
- Consider epoxy grout for showers, as covered in our epoxy grout guide, but only if you can work quickly and follow the packet exactly.
- Keep the shower dry until the grout has cured as the packet says, and let any new silicone cure too, as explained in how long silicone takes to dry.
Common mistakes when you grout tiles
- Wiping too early or with a soaking sponge, which pulls grout out of the joints and leaves pinholes that later collect dirt and moisture.
- Adding extra water to stretch a stiff mix, which weakens the grout, changes its colour and makes it crack and powder in time.
- Mixing a huge batch at once, so the last half goes off in the bucket before you can press it into the joints.
- Grouting corners and tile-to-bench joints that need flexible silicone, which leads to cracks the first time the building moves.
- Scraping or grinding old wet-area linings in a pre-1990 home without checking for asbestos first.
- Skipping a decent clean afterwards, so a thin film of haze dries on the tile and takes acid cleaner to shift. Our how to clean grout guide covers the aftercare.
When to call a handyman to grout tiles (or a licensed trade)
- The tiles sound hollow when you tap them, or any tile is cracked, loose or lifting, and needs to be re-laid before any grout goes on.
- You have a leaking shower, damp plasterboard or a musty smell, which points to failed waterproofing; book a licensed plumber such as TQN Plumber.
- The bathroom is in a home built or renovated before 1990 and you are unsure about the wall or floor lining.
- The job is large, the grout is epoxy, or you only have an hour or two and need it finished and cleaned in a single visit.
- You are renting, in which case you need written consent from the landlord before changing grout, tiles or any wet-area finish.
- The old grout has deep black mould that keeps coming back after cleaning, which often means the joint is wet from behind.
Cost to hire a handyman to grout tiles in Sydney
Prices below include GST and come from October 2026 Sydney handyman data. Grouting is usually quoted by time and area, so expect your quote to follow the hourly or half-day rate rather than a fixed figure.
| Job | Low | Typical | High |
|---|---|---|---|
| Handyman hourly rate, Sydney | $57 | $105 | $140 |
| Call-out or minimum charge, Sydney | $92 | $140 | $170 |
| Half-day handyman, Sydney (4 hours) | $230 | $415 | $645 |
| Full-day handyman, Sydney (8 hours) | $435 | $690 | $1025 |
| Weatherproofing or resealing with silicone, Sydney (per job) | $115 | $205 | $345 |
- Ask whether the quote includes raking out old grout, the grout itself and cleaning up, because removal is often the slowest part.
- A full day can cost less than eight hourly-billed hours, so a whole bathroom may suit a day rate.
- Bundle the resealing of corners and edges into the same visit, since the tape, silicone and tools are already on site.
- Rates for grouting a specific room or area vary widely with tile size and access (indicative — get itemised quotes).
FAQ: how to grout tiles
How to grout tiles for the first time?
Clear and vacuum the joints, mix cement grout exactly to the packet, and press it in with a rubber float held at an angle. Scrape off the excess, wait for the grout to firm, then wipe gently with a barely damp sponge. Buff the haze off once dry.
How to grout floor tiles without ruining them?
Plan an exit route, grout in small sections and use a grout suited to floors and your joint width. Press it into the joints in both directions, wipe lightly and stay off the floor until the packet says it can take traffic. Avoid mopping early.
How to grout wall tiles so the grout doesn’t slump?
Work from the top down and mix the grout slightly stiffer, staying within the packet’s water range. Pack the joints firmly with the float, then wipe with a nearly flat, barely damp sponge. Leave corners and bench joints clear for silicone.
How to grout shower tiles that keep going mouldy?
Rake out the old grout fully, fix any loose tiles, then regrout the flat joints and use flexible silicone in the corners. If mould returns quickly, water may be getting behind the tiles, and you should book a licensed plumber to check the waterproofing.
Getting your tiles grouted in Sydney
If you’d rather not work out how to grout tiles yourself, we can rake out, regrout and reseal your bathroom, kitchen or laundry in one visit and clean up before we leave. Read the epoxy grout guide to choose a product first, or book tile grouting in Sydney and add any other small jobs to the same visit.
Related guides
- Epoxy grout: when to use it and how it differs from cement grout
- Shower regrouting: how to replace failed grout
- Grout types and colours for floors, walls and showers
- How to silicone a shower for a clean, watertight seal
- How to remove silicone before regrouting
- How to clean grout and keep it looking new
- How long does silicone take to dry?


