Paving Cost per Square Metre in Sydney (2026 Guide)

Paving cost per square metre in Sydney typically runs from about $90 to $250 installed for common pavers (indicative — get itemised quotes). The biggest drivers are the paver material, base preparation, site access and drainage, not the paver price alone.

This guide breaks down paving cost per square metre by material and city, what pushes a quote up, when DIY makes sense, and what a fair quote includes. If you are planning a wider outdoor project, our guide to building a deck covers the alternative.

Key points

  • Most residential paving lands between about $90 and $250 per square metre installed in Sydney, with natural stone at the top end (indicative — get itemised quotes).
  • The biggest cost driver is groundwork: excavation, a compacted base, drainage falls and removing what is already there.
  • The cheapest route is concrete pavers on a simple, flat, easy-access area, and the next saving is doing the demolition and clean-up yourself.
  • DIY suits small, flat areas, but drainage changes need a licensed plumber and jobs valued at more than $5,000 may need a licensed builder.

Paving cost per square metre: price table

These indicative Sydney ranges include GST and cover typical residential jobs on reasonably flat ground (indicative — get itemised quotes). Prices vary with access, slope and the condition of the site.

Paver typeMaterials per m²Labour per m²Total installed per m²
Concrete pavers cost per m2$35–$80 (indicative)$55–$100 (indicative)$90–$180 (indicative)
Clay brick pavers$50–$110 (indicative)$60–$110 (indicative)$110–$220 (indicative)
Porcelain outdoor pavers$60–$130 (indicative)$70–$120 (indicative)$130–$250 (indicative)
Natural stone (bluestone, travertine, sandstone)$80–$200 (indicative)$80–$140 (indicative)$160–$340 (indicative)
  • Labour is a large share of the total, because excavating and compacting the base takes longer than laying the pavers.
  • Small areas often cost more per square metre, since set-up and minimum charges are spread over fewer pavers.
  • Ask whether quotes include GST, waste removal and cutting, because these are the lines that often differ.

Paving cost per square metre by city

Sydney usually sits at the upper end because of access, parking and labour costs, with other capitals varying with local rates (indicative — get itemised quotes).

CityIndicative total per m² (concrete pavers)Handyman hourly rate
Sydney$100–$200 (indicative)$57–$140 (typical $105)
Melbourne$90–$190 (indicative)$52–$125 (typical $94)
Brisbane$90–$185 (indicative)Ask for quotes
Paving cost per m2 Perth$85–$180 (indicative)Ask for quotes
Adelaide$85–$175 (indicative)Ask for quotes

The handyman rates are October 2026 figures and the paving ranges are indicative only, so compare at least three written quotes.

What affects paving cost per square metre

  • Paver material: concrete pavers cost least, while porcelain and natural stone raise both the materials and the cutting time.
  • Groundwork: soft clay, sloping ground or old concrete to remove add excavation and tip fees before a single paver goes down.
  • Base quality: a properly compacted base costs more upfront, but cheap bases sink and need relaying.
  • Access: a narrow side passage in an Inner West terrace means barrows rather than a bobcat, and labour rises accordingly.
  • Pattern and cuts: herringbone, curves and lots of edge cuts take longer than straight stretcher-bond laying.
  • Drainage: falls toward a drain are essential, and any stormwater pipework needs a licensed plumber.
  • Edges and retaining: edging, steps and a low wall add cost, so see our retaining wall cost guide if the site is sloped.
  • Old homes: in a pre-1990 home, check for fibro offcuts or old sheeting in the soil, and treat suspect material as asbestos until identified.

Cost to lay pavers: DIY vs hiring for paving

A small patio or path is a realistic weekend job, but a large area quickly becomes heavy, repetitive labour.

FactorDIYHiring a pro
CostMaterials and tool hire only, so a lower outlayLabour and margin added, with a written quote and a workmanship warranty
TimeSeveral weekends for a typical patio, longer for large areasUsually a few days, depending on the size of the job
Skill neededLevels, falls, compaction and cutting take practiceExperienced crews set falls and finish edges neatly
Heavy liftingPavers and base material are heavy, so use a helperThe crew handles lifting, barrowing and cutting
LicensingNone for you, but drainage changes need a licensed plumberAsk about licensing, because residential building work valued at more than $5,000 must be done by someone licensed by Building Commission NSW
Best forSmall, flat areas with easy accessLarge, sloped, drainage-sensitive or awkward sites
  • Our how to lay pavers guide covers the full DIY method and tools.
  • If you want a raised deck rather than paving, exempt development limits for decks, patios and pergolas apply, including a 25 m² maximum each and a floor no more than 1 m above ground, so confirm with council or the NSW Planning Portal.
  • Handyman rates in Sydney are $57 to $140 per hour (typical $105) with a call-out of $92 to $170, which suits repairs and re-laying a few pavers.

Paving installation cost: how to save without cutting corners

  1. Choose concrete pavers for large areas and keep premium stone or porcelain for a small feature section, such as an entry or dining zone.
  2. Keep the layout simple, with straight lines and few cuts, because pattern and cutting time are big labour costs.
  3. Clear plants, old edging and loose material yourself before the crew arrives, and agree in writing what you are removing.
  4. Book in off-peak weeks when crews are quieter, and ask whether grouping paving with other outdoor work reduces the price.
  5. Get three written, itemised quotes for the same area, base and paver, so you are comparing like with like.
  6. Do not skimp on the base and drainage, because relaying a sunken paved area costs far more than doing it properly once.

What a fair paving quote should include

  • Itemised materials: paver type and size, base material, sand, edging and jointing, with the area in square metres.
  • Groundwork: excavation, compaction, falls to drainage and what happens to spoil and waste.
  • Access and equipment: any extra charge for hand-carrying materials, hiring a compactor or removing existing surfaces.
  • Site checks: Dial Before You Dig for underground services, and a plan for drainage and nearby trees or fences.
  • The contractor’s licence number where licensing applies, plus insurance details.
  • A written contract: work under $20,000 uses a small jobs contract, while work over $20,000 needs a full home building contract plus Home Building Compensation cover.
  • Payment terms, where the maximum deposit before work starts is 10%.
  • Warranty terms in writing, plus related jobs like fence and gate repair if you want them done in one visit.

FAQ: paving cost per square metre

How much does paving cost?

Most residential paving in Sydney costs about $90 to $250 per square metre installed (indicative — get itemised quotes). Concrete pavers sit at the lower end, while porcelain and natural stone cost more, and sloped or hard-access sites push quotes higher.

How much is paving per m2 for a small patio?

Small patios often cost more per square metre because set-up and minimum charges are spread over fewer pavers. Expect the upper half of the indicative range, and ask for an itemised quote that separates materials, groundwork and labour (indicative — get itemised quotes).

What is the paving cost per m2 in Perth?

Perth is typically a little below Sydney for concrete pavers, but sand, base materials and access vary by suburb (indicative — get itemised quotes). Compare at least three written quotes from local paving contractors for the same area and finish.

Is it cheaper to lay pavers yourself?

Usually yes for small, flat areas, because you save labour. But hiring a compactor, buying the right base and getting falls to drainage right takes time. Our paver laying guide shows what is involved before you decide.

Do you need approval to pave your backyard?

Often not for simple paving, but rules vary with drainage, heritage listing and the type of structure. Check with your council or the NSW Planning Portal first, especially if the work involves a retaining wall, a raised deck or changes to stormwater.

Getting your paving priced in Sydney

If you want help scoping the job, we can inspect the site, quote the groundwork and book the right trades for drainage or larger building work. Book a handyman in Sydney for small paving repairs, edging and finishing jobs, and ask for an itemised quote before work starts.