How to mount a TV on the wall: choose a bracket that matches the screen’s VESA pattern and weight, find studs or solid masonry, drill pilot holes, bolt the wall plate on level, then hang the TV and tidy the cables. The most common failure is fixing a heavy bracket into hollow plasterboard with the wrong anchors, so the wall type decides everything.
This guide covers how to mount a TV on the wall step by step, the right fixings for plasterboard, brick and tile, how high to mount it, which bracket to buy, and what a handyman charges in Sydney if you’d rather not drill.
Key points
- The wall decides the method: timber studs and solid brick take lag bolts or masonry anchors, while plasterboard on its own needs rated hollow-wall anchors and suits light, flat brackets only.
- A stud finder with cable and pipe detection is the one tool you can’t skip, because power often runs vertically above and below a TV point.
- Anchor the TV or its cabinet even if you don’t wall-mount it; tip-overs injure young children, and TVs are the most common appliance involved.
- A Sydney handyman typically charges about $205 to mount a TV (range $115–$290, October 2026), and a new power point behind it needs a licensed electrician.
How to mount a TV on the wall safely: can you DIY it?
Most people can mount a small or medium TV on a flat bracket in a single visit to the hardware store. Use this table to check your situation first.
| Your situation | DIY OK? | Why |
|---|---|---|
| Flat or tilt bracket into timber studs | Yes | Lag bolts into the centre of two studs give the strongest, simplest fixing for most screens. |
| Solid or double brick wall | Yes, with a hammer drill | Masonry anchors hold well, but you need the right bit, a steady drill and dust control. |
| Plasterboard with no stud where you need it | Only light TVs and flat brackets | Hollow-wall anchors must be rated above the TV plus bracket weight; check the packet rating, never guess. |
| Full-motion or swing-arm bracket | Experienced DIYers only | An extended arm multiplies the leverage on the top fixings, so it needs studs or masonry, not plasterboard alone. |
| Tiled wall, fibro or a pre-1990 home | Check first | Tiles crack easily, and homes built or renovated before 1990 may contain asbestos in wall sheeting. |
| You’re renting | Ask the landlord first | Get written consent before drilling, and agree who patches the holes when you move out. |
| You want a power point behind the TV | No | Any new or moved power point is electrical work and needs a licensed electrician in NSW. |
Tools and materials to mount a TV on a wall
| Item | What it’s for | Tip |
|---|---|---|
| TV wall mount bracket | Holds the screen to the wall | Match the VESA hole pattern on the back of your TV and stay inside the bracket’s maximum weight and screen size. |
| Stud finder with AC detection | Finds studs, live cables and pipes | Scan the whole area twice, horizontally and vertically, and mark every hit in pencil before you drill. |
| Drill and bits | Pilot holes and anchor holes | Use wood bits for studs, masonry bits with hammer mode for brick, and a tile bit without hammer for tiles. |
| Spirit level | Keeps the wall plate straight | A long level beats the small bubble on the bracket, which is often slightly out on cheaper mounts. |
| Fixings | Lag bolts, masonry anchors or hollow-wall anchors | Use the fixings suited to your wall, not just the ones in the box; brands like Ramset list ratings on the packet. |
| Socket set and screwdriver | Tightening bolts and attaching the arms | Tighten firmly but stop when snug; overtightening can crush plasterboard or strip a stud hole. |
| Cable cover and ties | Hides HDMI and power leads | A paintable surface raceway from Bunnings is the neat DIY option that needs no work inside the wall. |
How to mount a TV on the wall: step by step
Allow time for a second person; lifting a large screen onto a bracket is a two-person job.
- Check the back of the TV for the VESA pattern and weight, then confirm the bracket covers both, including the screen size range on the box.
- Decide the screen height with painter’s tape on the wall, sitting where you’ll watch, so the centre of the screen is close to seated eye level.
- Scan the area with a stud finder for studs, cables and pipes, and avoid the vertical and horizontal lines running from nearby power points and switches.
- Mark the stud centres or the solid masonry area, then hold the wall plate on the marks and check it is level before marking the holes.
- Drill pilot holes into the centre of each stud, or drill to the anchor’s stated depth in brick, and vacuum the dust out of masonry holes.
- Fix the wall plate with the correct bolts or anchors, recheck it with the level, and tighten each fixing until snug without crushing the lining.
- Attach the vertical arms or plate to the back of the TV using the supplied spacers so the screws reach the inserts without bottoming out.
- Lift the TV with a helper, hook the arms onto the wall plate, and engage the safety screws or locking tabs that stop it lifting off.
- Adjust the tilt or level screws, then pull gently on each corner to confirm the bracket doesn’t move or flex away from the wall.
- Run HDMI and power leads through a surface cable cover, leave slack for tilting, and keep the power plug within easy reach of the outlet.
Mounting a TV on plasterboard walls
Most Sydney units and newer houses have plasterboard on timber or steel studs, so learning how to mount a TV on the wall here starts with finding the framing. If you can’t find a stud with the stud finder guide, don’t rely on guesswork.
- Fix into at least two studs wherever the bracket width allows; studs are commonly spaced at about 450–600 mm centres (indicative — confirm with a stud finder).
- Use hollow-wall anchors only when no stud lines up, and only for a light TV on a flat or slim tilt bracket within the packet’s rating.
- Choose metal toggle-style anchors over plastic plugs; our wall plugs and anchors guide compares the main types and where each one belongs.
- Steel studs need fixings designed for thin-gauge steel, as standard lag bolts won’t bite; check the stud type before buying fixings.
- Don’t use plasterboard-only fixings for a full-motion arm, because leverage on the top anchors increases every time you pull the screen out.
- If the right spot falls between studs, a timber noggin or backing board fixed across two studs spreads the load safely.
Mounting a TV on brick, concrete and tiled walls
Masonry walls hold heavy TVs well, and how to mount a TV on the wall in brick mostly comes down to the right bit and anchor. Our guide to drilling into brick and guide to drilling into tiles cover each surface in detail.
- Drill solid brick with a masonry bit in hammer mode, keep the drill square to the wall, and blow or vacuum dust from each hole.
- Use sleeve anchors or screw bolts sized for the bracket holes in brick or concrete, and follow the anchor maker’s hole diameter and depth.
- Check for hollow cores in modern bricks, as fixings in a hollow core lose much of their grip; move the plate if the bit suddenly drops through.
- Drill tiles with a tile or diamond bit, hammer mode off, at low speed, with masking tape over the mark to stop the bit wandering.
- Avoid drilling within a few centimetres of a tile edge, where cracks start easily (indicative — larger tiles are less forgiving).
- Treat fibro or old sheeting in a pre-1990 home as possible asbestos, and get it checked before you drill, cut or sand.
How high to mount a TV on the wall
Height matters more than most people expect, because a screen that’s too high causes neck strain within weeks.
- Aim for the centre of the screen at roughly seated eye level, often around 1 m to 1.1 m from the floor in a living room (indicative).
- Mount a little higher in a bedroom if you watch from bed, and add a tilt bracket so the screen angles down toward you.
- Avoid mounting above a fireplace unless you have a tilt or drop-down mount, as heat and a steep viewing angle both cause problems.
- Check that the bottom of the TV clears the top of any cabinet, soundbar or speaker you plan to place beneath it.
- Tape a cardboard template the size of the screen to the wall and sit with it for a day before drilling any holes.
- Measure from the bracket’s hook point, not the top of the wall plate, as the TV’s position on the arms changes the final height.
Choosing a TV wall mount bracket
| Bracket type | Best for | Wall needed | Watch out for |
|---|---|---|---|
| Flat (fixed) | A slim look where you sit straight in front | Plasterboard with rated anchors, studs or brick | No access to ports once mounted unless you plan cables first. |
| Tilt | Bedrooms, higher placements and glare control | Studs or brick for larger screens | Tilt mechanisms on cheap mounts can loosen over time. |
| Full-motion (swing arm) | Corners, open-plan rooms and multiple seats | Studs or masonry only | Leverage on the wall fixings; overloaded arms can droop. |
| Ceiling or drop-down | Shops, bedrooms or no usable wall | Ceiling joists | Overhead work needs a second person; see our TV ceiling mount guide. |
Common mistakes when you mount a TV on a wall
- Using the plastic plugs from the bracket box in plasterboard for a heavy screen, instead of fixings rated above the combined TV and bracket weight.
- Skipping the cable and pipe scan, then drilling straight down from a power point into a live cable running to the outlet.
- Trusting the bracket’s built-in bubble instead of a proper level, which leaves the screen visibly crooked once it is hung.
- Overtightening bolts in plasterboard or soft timber, crushing the lining or stripping the hole so the fixing loses grip.
- Ignoring asbestos risk in homes built or renovated before 1990, especially when drilling old fibro, eaves or wet-area sheeting.
- Lifting a large screen alone, which risks a cracked panel, a dropped TV and a strained back in the same moment.
When to call a handyman to mount your TV (or a licensed trade)
- You can’t find a stud or solid masonry where the TV needs to go, and the screen is too heavy for hollow-wall anchors.
- You want a full-motion arm on plasterboard, which needs a timber noggin or backing board installed first.
- The wall is tiled, fibro, rendered or part of a pre-1990 home where hidden asbestos or cracking risk is high.
- You need a power point moved or added behind the screen; that work needs a licensed electrician such as TQN Electrician.
- You’re renting and want the job done neatly so holes can be patched cleanly at the end of the lease.
- The TV is large, the mount is overhead, or you don’t have a second person to lift and hold it in place.
TV wall mounting cost in Sydney
Prices below include GST and come from October 2026 Sydney and Melbourne metro data. Our TV wall mounting cost guide breaks down extras like cable covers and brackets.
| Job | Low | Typical | High |
|---|---|---|---|
| TV wall mounting, Sydney (per job) | $115 | $205 | $290 |
| TV wall mounting, Melbourne (per job) | $105 | $190 | $260 |
| Handyman hourly rate, Sydney | $57 | $105 | $140 |
| Call-out or minimum charge, Sydney | $92 | $140 | $170 |
| Half-day handyman, Sydney (4 hours) | $230 | $415 | $645 |
- The bracket is usually extra unless you supply it, so ask whether the quote includes the mount, fixings and a cable cover.
- Book several small jobs in one visit, such as hanging a heavy mirror or installing a letterbox, to make the minimum charge work harder.
- Outdoor mounting jobs, like the ones in our wall mounting outdoor gear guide, often price the same as indoor TV jobs.
FAQ: how to mount a TV on the wall
How do you mount a TV on the wall without studs?
On plasterboard with no stud, use heavy-duty metal hollow-wall anchors rated above the TV and bracket weight, and choose a flat or slim tilt bracket. For larger screens or swing arms, install a timber noggin between two studs first, or move the TV to a brick wall.
How high should a TV be mounted on the wall?
Place the centre of the screen close to seated eye level, often around 1 m to 1.1 m from the floor in a lounge room (indicative). Tape a cardboard template to the wall and sit with it for a day, then adjust before drilling.
Can I mount a TV on the wall in a rental?
Ask your landlord in writing before drilling, and agree how the holes will be patched when you leave. NSW rules let tenants request some minor changes, but you still need consent first. A surface cable cover keeps the job neat and reversible.
What size TV wall mount do I need?
Match the VESA hole pattern on the back of your TV, then check the bracket’s maximum weight and screen size. Both must cover your TV with some margin. If the box lists a range, your TV’s pattern and weight should sit comfortably inside it.
Can you hide TV cables inside the wall?
A surface cable cover is the simple DIY option. Running a new power point behind the TV is electrical work that needs a licensed electrician in NSW. Never run a standard power cord inside a wall cavity, and ask the electrician about a recessed outlet.
How much does it cost to mount a TV in Sydney?
A Sydney handyman typically charges about $205 to mount a TV, with a range of $115 to $290 per job (October 2026). Expect more for a full-motion arm, brick or tile drilling, or a ceiling mount, and check whether the bracket is included.
Getting your TV mounted in Sydney
If you’d rather not work out how to mount a TV on the wall yourself, we can mount it safely, level and with cables tidied in one visit. Our handymen bring stud finders, masonry and tile bits, and the right anchors for your wall. Book TV wall mounting in Sydney and bundle any other small jobs on the same visit.
Related guides
- TV wall mounting cost: what’s included and what’s extra
- TV ceiling mount: brackets, joists and installation
- How to use a stud finder to locate studs and cables
- Wall plugs and anchors for plasterboard, brick and concrete
- How to childproof your home, including anchoring TVs and furniture
- How to hang things in a rental without losing your bond


