How to Use a Stud Finder: Step-by-Step Guide

How to use a stud finder: calibrate it on a blank patch of wall, slide it slowly across, mark both edges where it signals, then confirm the centre by scanning from the other side. The most common mistake is trusting one beep without checking for cables and pipes next to the stud. A Sydney handyman typically charges $140 as a call-out or minimum (range $92–$170), and will find studs and fix the item in the same visit.

Key points

  • It is an easy job of about 9 steps, but you should scan every wall twice because a single reading can be wrong.
  • The one tool you cannot skip is the stud finder itself, ideally one that also shows live wiring and metal pipes.
  • Treat every wall as if it has wiring or pipes in it, and keep clear of lines running up, down or sideways from switches and power points.
  • A Sydney handyman typically charges $205 to mount a TV (range $115–$290) and $125 for picture or shelf hanging (range $80–$205).

What is a wall stud?

A wall stud is a vertical framing member inside a timber or steel-framed wall, and it is the part of the wall that holds a screw firmly.

TermMeaningWhy it matters
StudA vertical timber or steel member that forms the frame of a wallScrews bite into it, so heavy items such as TVs, shelves and cabinets belong on studs.
NoggingA horizontal piece of framing between studsIt gives you a fixing point between studs, but a standard detector may not find it.
PlasterboardThe sheet lining fixed over the frameIt is brittle on its own, so it needs a rated anchor if you cannot reach a stud.
CavityThe hollow space between the studs behind the liningCables and pipes often run through it, which is why you scan before you drill.
PlateThe horizontal top and bottom framing memberIt marks the ends of each stud and anchors the wall to the floor and ceiling.

Can you use a stud finder yourself?

Yes, because it is a handheld tool, but the wall construction decides how much to trust the reading.

SituationDIY OK?Why
Standard plasterboard on a timber frameYesThis is the easiest case, and a detector usually finds the edges clearly.
Steel-framed walls in units and commercial fit-outsYes, with careMagnetic or metal detection responds to the frame, but fixing needs steel-suitable screws.
Brick, block or concrete wallsNot applicableThere are no studs, so you fix into the masonry with the right plug and bit.
Textured, tiled or thick-lined wallsHarderThe extra layer confuses many detectors, so confirm with a second method.
Home built or renovated before 1990Check firstWalls may contain asbestos, so check asbestos.nsw.gov.au before drilling suspect sheeting.
Rental propertyAsk firstScanning is harmless, but drilling needs consent, so ask before you fix anything to the wall.

Tools and materials

Most of the kit is cheap, and a stud finder from Bunnings covers the basics.

ItemWhat it is forTip
Stud finderLocating the edges and centre of each studPick a model that also senses live wiring and metal, and read its manual.
Masking tape and pencilMarking edges without scarring the wallUse low-tack tape to avoid pulling paint off.
Small nail or fine drill bitConfirming the stud with a pilot holeDrill in a spot that will be hidden by the fixing.
MagnetFinding the screw heads that fix plasterboard to the frameSlide a strong magnet across the wall until it grabs.
Tape measure and spirit levelChecking spacing and plumb linesStuds repeat at regular intervals, so use that pattern to confirm your marks.
Drill and fixingsFixing the item after you find the studSee wall plugs and anchors for other wall types.

How to use a stud finder: step by step

  1. Read the manual, choose the right scanning mode for the wall, and put in a fresh battery, because a weak battery gives patchy readings.
  2. Place the finder flat on a blank part of the wall away from corners, switches and power points, and hold it still while it calibrates.
  3. Slide it slowly across the wall in one direction and keep a steady pressure, so the sensor does not skip over the edge of a stud.
  4. Mark the spot where it first signals, and keep sliding until the signal drops away so you mark the second edge as well.
  5. Repeat from the other direction, sliding back across the same line, and check that the new marks fall in the same places.
  6. Take the midpoint between the two marks as the centre of the stud, and run a vertical line to check it follows the wall.
  7. Use the same method higher and lower on the wall, because studs run vertically and your marks should line up in a straight line.
  8. Confirm with a pilot hole or a magnet on the screw heads, and stay clear of any warning the detector gives for wiring or metal.
  9. Drill, fix and check the item is firm before loading it, and leave heavy items to a handyman if you are unsure.

How to find a stud in a wall without a stud finder

Low-tech methods work, but they are less reliable, so confirm with a pilot hole before you commit.

  • Knock along the wall and listen for the dull, solid sound, which changes from hollow to solid over a stud.
  • Use a magnet to find the screw heads or nails that fix the plasterboard to the studs, which sit in a vertical line.
  • Start from a corner or a window or door frame, since studs usually sit alongside these openings.
  • Look for the vertical line of electrical boxes, because power points are often fixed to the side of a stud.
  • Drill a small pilot hole in a hidden spot, and feel for resistance that suggests solid timber rather than a hollow cavity.
  • Check the other side of the wall, such as in a cupboard or roof space, where you may see the framing directly.

How to use Stanley stud finder models

Models differ, so follow the manual that came with yours, but these principles apply to most handheld units.

  • Check which mode your unit has, such as stud scan, deep scan or metal and AC detection, and pick the one that matches the wall.
  • Calibrate on a blank patch of wall, with the unit flat and still, until it signals that it is ready.
  • Slide the unit slowly and in one direction, and mark the point where it signals the edge of a stud.
  • Do not press harder to compensate for a weak signal, since pressure changes the reading and can give false edges.
  • Treat the live-wire warning as a prompt to stop and check, never as proof that a wall is safe to drill.
  • If the readings are inconsistent, reset and try again from a different starting point, or ask a handyman to confirm.

How to find a stud in a wall: tricky wall types

The lining and frame change what your finder can and cannot see.

  • On plasterboard over timber, the standard scan works well, and screw heads or nail lines help you confirm.
  • On steel studs, a magnet or metal mode picks up the frame, and you must use screws that suit steel.
  • On lath and plaster in older terraces, a detector can struggle, so test several spots and rely on a pilot hole.
  • On tiled walls, the tile and adhesive hide the frame, and you should read how to drill into tiles before drilling.
  • On double brick or concrete, there is no stud, so see how to drill into brick for masonry fixings.
  • Near wet areas and kitchens, expect pipes and cables behind the lining, and stop if the detector flags anything.

How to build a wall frame in Australia

A wall frame is a series of studs between a top and bottom plate, and the detail matters more than the carpentry.

  • Only build a non-load-bearing partition yourself; load-bearing walls and structural alterations need a licensed builder and engineering advice.
  • Work valued over $5,000 must be done by someone licensed by Building Commission NSW, and larger jobs need a written contract.
  • Follow the manufacturer’s and designer’s instructions for stud sizes and spacing, because the right figures depend on the wall’s job.
  • Check for asbestos before you cut into or alter old walls in a pre-1990 home, and never remove suspect material yourself.
  • Leave electrical and plumbing rough-in to a licensed electrician or plumber before the wall is lined.
  • Read our stud wall guide for the full build method and the steps that come after the frame is up.

Common mistakes with a stud finder

  • Calibrating over a stud or cable, which sets the baseline wrongly and gives a reversed reading.
  • Sliding too fast, so the sensor skips over the edge of the stud and you mark the wrong place.
  • Trusting the live-wire indicator as a guarantee, when it is only a warning.
  • Drilling without checking for cables and pipes, especially beside power points, switches and bathrooms.
  • Ignoring asbestos in pre-1990 homes, and drilling or sanding old sheeting without checking first.
  • Hanging a heavy TV or cabinet on a single marked point without a second person to hold it, or without anchoring tall furniture against tip-overs.

When to call a handyman (or a licensed trade) for studs

  • The wall is heavy-duty, such as for a TV, and you want the fixings into framing; our TV wall mount guide shows the method.
  • Your detector gives mixed results or the wall is tiled, lath and plaster or double brick.
  • A wire or pipe warning shows up, in which case a licensed electrician or plumber should check it.
  • The job includes new power points, lights or rewiring, which always needs a licensed electrician.
  • You are planning a kitchen refit and want fixing points marked first; see kitchen renovation cost, and use epoxy grout for splashback gaps.
  • You are building or altering a wall frame, where a builder should confirm what is structural.

Cost to hire a handyman to find studs and fix to them in Sydney

Prices include GST and come from October 2026 Sydney handyman data.

JobLowTypicalHigh
TV wall mounting, Sydney$115$205$290
Picture or shelf hanging, Sydney$80$125$205
Handyman hourly rate, Sydney$57$105$140
Call-out or minimum charge, Sydney$92$140$170
Half-day handyman, Sydney (4 hours)$230$415$645
Full-day handyman, Sydney (8 hours)$435$690$1025
  • The minimum charge applies even to a five-minute fix, so bundle your scanning, mounting and hanging into one visit.
  • A full day can cost less than eight hours billed hourly, which suits a long list of fixing jobs.
  • Ask whether wall plugs, brackets and fixings are included or charged on top, and get a written quote.

FAQ: how to use a stud finder

How to use a stud finder on plasterboard?

Calibrate it on a blank patch of wall, then slide it slowly across until it signals the first edge and mark it. Keep going until the signal drops and mark the other edge. The centre between the marks is the stud, which you should confirm by scanning back the other way.

How to find a stud in a wall?

Use a stud finder, or knock for a solid sound, or use a magnet to find the screw heads that fix the plasterboard. Studs sit beside doors, windows and power points, and repeat at regular intervals. Confirm with a small pilot hole in a hidden spot.

What is a stud in a wall?

A stud is a vertical framing member, made of timber or steel, that forms the skeleton of an internal or external wall. The plasterboard or lining is screwed to it. Studs are where screws hold best, which is why heavy items go on them.

What is a wall stud made of?

Most Australian homes use timber studs, though steel studs are common in units and commercial fit-outs. Brick and concrete walls have no studs. Which type you have changes the screws, the anchors and the detector mode you should use.

How to use Stanley stud finder models?

Follow the manual for your model. Calibrate on a blank patch of wall, choose the right mode and slide slowly across the wall, marking the edges where it signals. Treat a live-wire warning as a prompt to stop, and never rely on it to say a wall is safe.

How to build a wall frame in Australia?

For a non-load-bearing partition, fix a top and bottom plate, add studs between them at regular spacing, and brace as the designer specifies. Load-bearing walls need a licensed builder. Work over $5,000 must be done by someone licensed by Building Commission NSW.

Getting studs found and items fixed in Sydney

If you would rather not guess, we can scan the wall, mark the studs and fix your TV, shelf or cabinet in one visit, and flag anything that needs a licensed electrician or plumber. Book a Sydney handyman for scanning and fixing, and read our wall plugs and anchors guide for the walls with no studs.