Here is how to drill into tiles: mark the spot with masking tape, use a tile or diamond-tipped bit at slow speed with the hammer action off, and let the bit cut with light pressure. The biggest thing that goes wrong is a cracked tile, which almost always comes from speed, force or the wrong bit. A Sydney handyman typically charges $140 as a call-out or minimum (range $92–$170), which is cheap next to replacing a tile.
Key points
- It is a simple job of about 8 steps, but patience matters more than power: slow speed and light pressure protect the glaze.
- The one tool you cannot skip is a bit made for tile, either carbide spear-point or diamond-tipped, matched to the tile type.
- Scan for cables and pipes first, and never drill through a shower waterproofing layer or near taps without a licensed plumber.
- A Sydney handyman typically charges $105 an hour (range $57–$140), with a minimum call-out of about $140.
Can you drill through tiles yourself?
Most tile jobs are fine for a careful beginner, but wet areas and old homes change the answer.
| Situation | DIY OK? | Why |
|---|---|---|
| Wall tile in a dry area such as a hallway or laundry splashback | Yes | Low risk once you have scanned for cables and pipes and chosen the right bit. |
| Floor tile | Yes, with care | You are drilling downwards, so keep the drill square and check what sits under the slab or subfloor. |
| Porcelain or large-format tile | Yes, with the right bit | Porcelain is dense and chips easily, so a diamond-tipped bit and slow speed are essential. |
| Shower recess or bath surround | Usually no | A hole can break the waterproofing; book a licensed plumber for anything touching pipes or waterproofing. |
| Home built or renovated before 1990 | Check first | Wet-area linings behind tiles may contain asbestos, so check asbestos.nsw.gov.au and treat suspect material as asbestos. |
| Rental property | Ask first | Get written consent before drilling; the NSW minor-change rules for anchoring furniture exclude tiled walls. |
| Above shoulder height | Two people | Use a stable ladder and have a second person steady it and hold the vacuum. |
Drill bit for tile: tools and materials
Hardware stores such as Bunnings stock every item below, and the bit is the only place worth spending extra.
| Item | What it is for | Tip |
|---|---|---|
| Carbide spear-point tile bit | Cutting through glazed ceramic wall tiles | A Sutton tile drill bit is one Australian option; check the packet for the tile types it suits. |
| Diamond-tipped or diamond core bit | Drilling porcelain and very hard tile | Use it at slow speed and keep it cool; never use hammer mode. |
| Cordless drill with variable speed | Controlled, slow starting speed | A cordless drill is safer than mains power when you use a little water. |
| Masonry or wood bit | Drilling the wall behind the tile once you are through | Match it to the wall plug packet and the material behind. |
| Masking tape and pencil | Stopping the bit skating and marking the centre | Use two overlapping strips in a cross. |
| Spray bottle of water | Keeping the bit cool | Dab or mist the bit only; keep water off the drill body and battery. |
| Cable and pipe detector | Scanning for hidden services | Our stud finder guide shows how to scan properly. |
| Wall plugs and screws | Fixing the item after drilling | See wall plugs and anchors, and follow the packet rating, not a guess. |
| Safety glasses and dust mask | Protecting eyes and lungs from fine tile and glaze chips | Wear them from the first touch of the bit. |
How to drill into tiles: step by step
- Scan the area with a detector and stay clear of lines running straight up, down or sideways from power points, switches and taps.
- Choose a drill bit for tile that suits the material, either carbide spear-point for ceramic or diamond-tipped for porcelain, and match its size to the plug.
- Stick a cross of masking tape over the mark so the bit does not skate across the glaze, then mark the centre of the cross with a pencil.
- Set the drill to its slowest speed and switch the hammer action off, because hammering is the quickest way to crack a glazed tile.
- Start with the drill tilted slightly to bite the glaze, then bring it upright and let the bit cut with light, steady pressure.
- Pause every few seconds to cool the bit with a light mist of water, keeping the drill body and battery dry.
- When the bit breaks through the tile, stop and swap to a masonry or wood bit that suits the wall behind, drilling only to the depth on the plug packet.
- Vacuum the dust, push in the plug and tighten the screw until it is snug only, since overtightening can crack the tile around the hole.
How to drill into tiles without cracking porcelain
Porcelain is harder than ceramic, so the usual carbide bit will overheat and skid before it cuts.
- Use a diamond-tipped bit rated for porcelain and check the packet, because a bit made only for ceramic wall tile will glaze over and stall.
- Run the drill at its slowest speed for the whole hole, and ease off if you hear squealing, which means the bit is overheating.
- Let the diamond cut rather than pushing, because heavy pressure is what chips the back of the tile as the bit exits.
- Keep the bit cool with a light mist of water every few seconds, and wipe the slurry away so you can see the hole.
- Drill at least a tile-width from a cut edge or corner where you can, since edges crack far more easily than the middle of a tile.
- Practise on a spare tile first if you have one, because hard porcelain behaves differently from the softer tiles on most bathroom walls.
How to drill through tiles on walls and floors
The method is the same, but what sits behind the tile changes the bit, the plug and the risk.
- On a stud wall, find the framing first with a stud finder and check the stud wall guide if you are unsure what lies behind the lining.
- On brick or concrete, swap to a masonry bit once through the tile, and read how to drill into brick before using any hammer action.
- On a kitchen splashback, check the position of power points and the cooktop, since extra tiling work in a kitchen renovation often hides cables.
- On a floor, drill straight down and avoid areas over slab penetrations, hydronic heating or any in-slab services you know about.
- Old Inner West terraces often have double brick behind the tiles, which blunts cheap bits fast, so keep a sharp masonry bit ready.
- After a bad hole, patch a small gap with matching grout, and see epoxy grout for hard-wearing repairs in wet areas.
Drilling tiles in a rental
In NSW a landlord cannot unreasonably refuse certain minor changes, but you must ask first and never drill without consent.
- Ask in writing before you drill, and say what you are fixing, where it goes and how you plan to make good when you leave.
- Picture hooks, nails and screws for hanging frames fall under the minor-change rules, but a tiled wall is a common sticking point.
- Securing furniture to a wall is covered for safety, except on a tiled wall, so propose a different fixing point for tall units.
- Use freestanding or adhesive options for towel rails and hooks instead, and check the packet for the surface they suit.
- Heritage properties, loose-fill asbestos register homes, strata and social housing have extra limits, so check your lease before you start.
- Keep photos of the wall before and after, and agree who pays for any repair, since the tenant pays unless agreed otherwise.
Common mistakes when drilling tiles
- Using hammer action on glazed tile, which sends cracks across the tile and often into neighbouring tiles too.
- Using a standard masonry or wood bit instead of a tile bit, so the bit skids and chips the glaze.
- Skipping the cable and pipe scan, especially close to taps, switches or behind a splashback.
- Drilling in a pre-1990 bathroom without checking for asbestos in wet-area linings or floor coverings.
- Overtightening the screw so the tile cracks around the plug, or fixing into grout instead of the tile and wall behind.
- Working above shoulder height on a ladder without a second person to steady it.
When to call a handyman (or a licensed trade) for drilling tiles
- You are working on porcelain or large-format tiles and do not own the right diamond bit or want to risk the tile.
- The job is inside a shower recess, where a licensed plumber should deal with waterproofing and any pipes.
- The wall is next to power points, switches or a rangehood, where a licensed electrician should check wiring or move it.
- You are fitting several items in one go, such as a mirror, shelf and towel rail, which suits a single bundled visit.
- The home was built or renovated before 1990 and you are unsure whether the lining contains asbestos.
- The fixing is heavy, such as a TV wall mount, which needs the right fixing into framing or masonry.
Cost to hire a handyman to drill into tiles in Sydney
Prices include GST and come from October 2026 Sydney handyman data.
| Job | Low | Typical | High |
|---|---|---|---|
| Handyman hourly rate, Sydney | $57 | $105 | $140 |
| Call-out or minimum charge, Sydney | $92 | $140 | $170 |
| Picture or shelf hanging (comparable small fixing job) | $80 | $125 | $205 |
| Half-day handyman, Sydney (4 hours) | $230 | $415 | $645 |
| Full-day handyman, Sydney (8 hours) | $435 | $690 | $1025 |
- The minimum charge applies even to a five-minute fix, so bundle all your holes into one visit.
- A full day can cost less than eight hours billed hourly, which suits a long list of small jobs.
- Ask whether bits, plugs and screws are included or charged on top.
FAQ: how to drill into tiles
How to drill into tiles without a special bit?
You should not. Standard masonry and wood bits skid on glaze and crack tile. Buy a tile or diamond-tipped bit for a few dollars, use slow speed, tape the spot and keep hammer action off. If the job involves porcelain or a shower wall, a handyman is the safer option.
Can you drill through tiles without cracking them?
Yes. Use the correct bit, mark the spot with masking tape, drill slowly with light pressure and mist the bit with water. Stay away from tile edges, and stop the moment you feel the bit pass through the tile so you do not force the wall behind it.
How to drill through porcelain tile without cracking?
Use a diamond-tipped bit made for porcelain, run the drill at its slowest speed with hammer off, and cool the bit with a light mist of water. Let the diamond do the cutting instead of pushing, and practise on a spare tile if you have one.
How to drill into porcelain tiles on a wall or floor?
The steps are the same on both. Scan for cables and pipes first, tape the spot, drill slowly with a diamond bit, then switch to a masonry bit for the wall or slab behind. On a floor, keep the drill square and avoid known in-slab services.
Getting your tiles drilled in Sydney
If you would rather not risk a good tile, we can drill, plug and fix towel rails, mirrors, shelves and brackets in one visit and flag anything that needs a licensed plumber or electrician. Book a Sydney handyman for tile drilling, and start with the stud finder guide if you are planning a larger job.


