How to lay pavers: excavate, lay and compact a firm base, screed a bed of sand, set the pavers tight, cut the edges, then sweep jointing sand into the gaps. The biggest thing that goes wrong is a poorly compacted base, because pavers sink and rock within a season. A Sydney handyman typically charges $105 an hour (range $57–$140), and bigger paving jobs are often priced per square metre by a landscaper.
Key points
- It is a hard, physical job of about 10 steps, and the time goes into the base, not the pavers themselves.
- The one tool you cannot skip is a plate compactor, which you can hire, because hand tamping will not compact a base evenly.
- Check for underground services before you dig, and treat any old fibro or sheeting in the soil as suspect asbestos.
- Work over $5,000 needs a licence in NSW, and a Sydney handyman typically charges a $140 minimum call-out (range $92–$170).
Can you lay pavers yourself?
A small, flat area is a fair DIY project, but size, levels and drainage decide whether it stays that way.
| Situation | DIY OK? | Why |
|---|---|---|
| Small patio or garden path | Yes | The area is easy to excavate and compact, and mistakes are cheap to fix. |
| Large patio or driveway | Usually hire out | Heavy loads need a deeper, more precise base, and the work is physically demanding. |
| Area next to the house | With care | You must slope away from the house and keep the damp course and termite inspection zones clear. |
| Sloping yard or retaining wall | Get advice | Retaining walls higher than 600 mm are outside the exempt development limits; confirm with your council. |
| Work valued over $5,000 | Licensed builder | Residential building work over $5,000 must be done by someone licensed by Building Commission NSW. |
| Rental property | Ask the owner | Paving is a permanent change, so get written consent and avoid doing it without the owner’s agreement. |
Tools and materials
Hire the heavy tools from Bunnings or a hire shop, and buy the materials after you have measured the area.
| Item | What it is for | Tip |
|---|---|---|
| Plate compactor (hire) | Compacting the base and bedding the pavers | Fit a rubber mat when you compact the finished surface. |
| Crushed rock base material | Forming a firm, free-draining sub-base | Ask the supplier which grade suits foot or vehicle traffic. |
| Bedding sand | Giving the pavers an even bed | Use clean, coarse sand and keep it free of stones and clay. |
| Concrete pavers | The finished surface | Buy extra for cuts and breakage, and follow the maker’s laying instructions. |
| String line, pegs and spirit level | Setting levels and falls | Check the fall away from the house with the level before and after each layer. |
| Angle grinder with diamond blade, or paver splitter | Cutting pavers | Wear a dust mask, hearing protection and safety glasses. |
| Rubber mallet and screed rails | Setting pavers and levelling the sand | Remove the rails and fill the gaps before laying. |
| Jointing sand or polymeric sand | Locking the pavers together | Follow the packet instructions for sweeping and wetting. |
How to lay pavers: step by step
- Mark out the area with pegs and string, check the edges are square, and decide the fall so water runs away from the house.
- Call Dial Before You Dig and check for pipes and cables, then dig out topsoil and roots to the depth the paver maker recommends.
- Compact the exposed ground with a plate compactor, removing any soft patches and replacing them with fresh crushed rock.
- Spread the crushed rock base in layers, compacting each layer thoroughly and checking the level and fall with the spirit level.
- Install edge restraints or a concrete haunch along the borders so the pavers cannot spread sideways once they are loaded.
- Lay screed rails and spread bedding sand between them, pulling a straight board across to form an even bed, then lift the rails and fill the gaps.
- Lay the pavers from one corner in your chosen pattern, tapping each firmly into the sand with a rubber mallet and keeping joints tight and even.
- Cut edge and corner pavers with a diamond blade or splitter, measuring each one individually and wearing a dust mask and eye protection.
- Sweep jointing sand over the surface, compact the pavers with the plate compactor and rubber mat, then sweep in more sand until the joints are full.
- Clean the surface, check that water runs away from the house, and leave the sand to settle before heavy use as the jointing sand packet advises.
How to lay pavers on sand
A sand bed over a compacted base is the standard method for paths and patios.
- Use clean bedding sand over the compacted base, and screed it level without walking on it before the pavers go down.
- Keep the sand layer even and at the thickness the paver maker specifies, since too much sand makes pavers settle unevenly.
- Lay the pavers directly onto the sand and tap them down, working from the edge you have fixed in place and moving outwards.
- Check the surface with a long level or straight edge every few rows, and lift and re-bed any paver that is high or low.
- Use edge restraints, because sand-bedded pavers will creep and spread without something holding the border in place.
- Sweep in jointing sand and re-compact, then top up the joints after the first heavy rain.
Laying pavers on sand and cement mix
A sand and cement bed, or a mortar base, suits steps, driveways and areas where pavers must not move.
- Mix the sand and cement to the ratio on the cement bag or the paver maker’s instructions rather than guessing.
- Lay the bed over a firm base or slab, and keep it damp enough to bind but not wet enough to flow.
- Work in small sections so the mix does not dry before you bed the pavers, and keep a bucket of water for cleaning.
- Expect the finished job to be hard to lift later, so be sure about the layout and levels before you start.
- Wipe cement off the paver faces straight away, since dried cement can stain concrete pavers permanently.
- Check whether you need a licensed builder if the work involves steps or retaining walls, or if the job is valued over $5,000.
How to lay pavers on dirt
You cannot lay pavers straight onto soil, because soil moves, holds water and grows weeds.
- Strip off turf, topsoil and roots first, because organic material rots and leaves hollows under the pavers.
- Compact the exposed ground and add a crushed rock base, even for a light garden path.
- Test for soft clay or fill by walking the area, and ask a landscaper if you find reactive or filled ground.
- Check for old fibro offcuts or sheeting buried in the soil in pre-1990 homes, and treat suspect material as asbestos.
- Slope the surface away from the house and keep it clear of the damp course and any termite inspection gap.
- Use weed membrane below the sand only if the paver maker recommends it.
How to cut pavers and lay concrete pavers
Concrete pavers are heavy and cut with a lot of dust, so set up your cutting area before laying.
- Mark the cut line on the face with a pencil and a straight edge, and measure each edge paver rather than copying the last one.
- Use a diamond blade on an angle grinder or hire a wet saw, and let the blade do the work without forcing it.
- Wear a dust mask, safety glasses and hearing protection, because cutting concrete creates fine silica dust.
- Use a paver splitter for straight cuts on edge pavers if you have a lot to cut, and keep your hands clear of the blade.
- Stack and lift concrete pavers carefully, using gloves and good lifting technique, because they are heavy and have sharp edges.
- Keep offcuts away from drains and gardens, and take them to a council-approved recycling facility.
Common mistakes when laying pavers
- Skipping the compaction, or compacting the base in one thick layer, so the pavers sink and rock within months.
- Laying pavers directly onto soil, or leaving organic material in the excavation, so hollows form under the surface.
- Forgetting the fall, so water runs back to the house or pools on the patio instead of draining away.
- Covering the damp course or termite inspection zone, which can hide moisture and let termites in unnoticed.
- Using a mortar bed on a poor base, so the pavers crack when the base moves.
- Cutting pavers without a dust mask or eye protection, or digging without checking for underground services.
When to call a handyman (or a licensed trade)
- The area is larger than a small patio or path, because hiring out the base and compaction saves time and back strain.
- You are building steps, a retaining wall or a raised area, where the exempt limits and engineering questions apply.
- The paving will carry a car or heavy trailer, where the base design and thickness need professional input.
- The work, including materials, is valued over $5,000, which needs a licence from Building Commission NSW.
- Drainage, stormwater pipes or taps are involved, where a licensed plumber must do anything touching pipes.
- You want paving joined to a deck or fence, and our deck building guide and fence building guide cover the rules.
Cost to hire a handyman to lay pavers in Sydney
Prices include GST and come from October 2026 Sydney handyman data.
| Job | Low | Typical | High |
|---|---|---|---|
| Handyman hourly rate, Sydney | $57 | $105 | $140 |
| Call-out or minimum charge, Sydney | $92 | $140 | $170 |
| Half-day handyman, Sydney (4 hours) | $230 | $415 | $645 |
| Full-day handyman, Sydney (8 hours) | $435 | $690 | $1025 |
- Paving is often quoted per square metre by landscapers, and the rate varies widely (indicative — get itemised quotes).
- For work under $20,000 a written small jobs contract applies, and the maximum deposit before work starts is 10%.
- For bigger projects see concrete driveway cost and retaining wall cost for comparison.
FAQ: how to lay pavers
How to lay pavers on sand?
Dig out the area, compact a crushed rock base, spread an even bed of bedding sand, then lay the pavers tightly and tap them down. Cut the edges, fit edge restraints, sweep in jointing sand and compact the surface. Follow the paver maker’s instructions for depths.
How to cut pavers?
Mark the line with a pencil and straight edge, then cut with a diamond blade on an angle grinder, a wet saw or a paver splitter. Wear a dust mask, safety glasses and hearing protection, and cut outdoors so the dust stays out of the house.
How to lay pavers on dirt?
You cannot lay them straight on soil. Remove turf and topsoil, compact the ground, add a crushed rock base in layers, then add bedding sand. This stops the pavers sinking and keeps weeds out. A base is needed even under a light garden path.
How to lay concrete pavers for a patio?
Mark the area, set the fall away from the house, build a compacted base and sand bed, then lay the pavers from a fixed corner. Cut edge pieces, lock the border with restraints, sweep in jointing sand and compact the finished surface.
Getting pavers laid in Sydney
If you would rather not hire a compactor and shift tonnes of material, we can prepare the base, lay small paths and patios and tidy up, and recommend a landscaper for larger areas. Book a Sydney handyman to lay pavers, and read the deck building guide if the paving meets a deck.


