Fence Repair: Complete Guide

Fence repair on a timber fence comes down to four moves: find the failed post or rail, support the panel, replace or reinforce the damaged part, then fix the palings back on with galvanised fixings. The biggest thing that goes wrong is treating a rotten or leaning post as a loose paling, so the repair fails the first time the wind picks up.

This guide covers fence repair, gate repair, fence post repair, post depth and attaching shade cloth, plus what a Sydney handyman charges. If you are planning a new structure instead, start with our deck building guide for the licensing and planning basics.

Key points

  • Difficulty: moderate, around eight steps, and most of the time goes on propping the fence and getting the post plumb.
  • The one tool you cannot skip is a spirit level, because a post that looks straight from the house can still lean.
  • Safety check: pre-1990 fibro fences and sheeting may contain asbestos, so do not cut, drill or sand them and see asbestos.nsw.gov.au.
  • A Sydney handyman charges about $105 an hour (range $57–$140) with a call-out or minimum of about $140 (range $92–$170).

Can you do fence repair yourself?

Many fence repairs suit a confident DIYer, but some situations call for a handyman or a licensed contractor.

SituationDIY OK?Why
Loose or split palings on a timber fenceYesSimple to replace with matching palings and galvanised nails or screws.
Sagging gate that dragsYesOften fixed by tightening hinges or adding a diagonal brace.
Leaning or rotten postMaybeYou need to prop the panels and handle concrete; ask a second person to help.
Old fibro fence from a pre-1990 homeNoTreat suspect sheeting as asbestos and do not drill, cut or break it.
Colorbond fence panelsNoBook a licensed Colorbond fencing contractor.
Pool fence or gateNoPool barriers have strict rules, so check with your council or a pool-barrier specialist.

Tools and materials for fence repair

Most of this kit comes from Bunnings, and the right fixings matter more than the brand.

ItemWhat it is forTip
Spirit levelChecking posts are plumb and gates hang squareCheck two faces of every post, not just one.
Post hole shovel or diggerOpening up around a failed post baseCall Dial Before You Dig if you are digging beyond the surface.
Quick-set concrete or dry-mixSetting a replacement postFollow the bag’s mixing and cure times exactly.
Galvanised nails, screws and bracketsFixing rails, palings and gate hardwareMatch the fixing to the timber; check the packet.
Props or timber offcutsHolding panels while you replace a postCheap, but needed to keep the fence from collapsing.
Drill, hammer and sawCutting and fixing timberWear glasses and gloves, and use the correct blade.

Fence repair: step by step

Work from the post outwards, because the posts carry the whole fence.

  1. Walk the whole fence line and mark every loose paling, cracked rail, lean and rotten post with chalk so you fix the cause, not the symptom.
  2. Check the age and material: if the panels are old fibro or sheeting in a pre-1990 home, stop and treat it as asbestos.
  3. Prop the panels either side of a bad post with timber props, then check they are stable before you remove any fixings.
  4. Remove the failed post by loosening the rails; dig out the base carefully and keep clear of buried cables and pipes.
  5. Set the new post, check it is plumb in both directions, and brace it while the concrete cures for the time shown on the packet.
  6. Reattach rails with galvanised brackets or screws, making sure the top and bottom rails sit level and square to the post.
  7. Replace split palings with matching timber, spacing each one evenly and using a paling as a gauge for the gap.
  8. Remove the props only after the concrete has cured, then shake test the fence and walk back down the line looking for gaps.

Gate repair: sagging, sticking and hardware

A gate drags because of a loose post, worn hinges or a frame that has pulled out of square.

  • Check the gate post first: if it moves when you lean on it, repair or reset the post before touching the gate.
  • Tighten or replace hinge screws with longer galvanised screws that bite into solid timber, not the softened old holes.
  • Add a diagonal brace running from the bottom of the hinge side to the top of the latch side to pull a sagging frame square.
  • Plane or sand a sticking edge only after you have fixed the sag, as removing timber hides the real fault.
  • Replace a failing latch or lock with matching hardware; for lock changes on a gate, book a licensed locksmith.
  • Do not repair a pool gate yourself, because self-closing and self-latching rules apply and a licensed professional should check it.

How to attach shade cloth to a fence

Shade cloth acts like a sail in wind, so the fence must be sound before you hang anything on it.

  • Repair any leaning posts and loose rails first, because the cloth will transfer wind load onto the whole fence.
  • Use shade cloth with reinforced edges and fix it to the timber with rust-proof clips or washers, as the packet recommends.
  • Space the fixings evenly along the top and bottom so the cloth does not flap or tear at the corners.
  • Keep the cloth taut but not stretched, and leave small gaps rather than a sealed wall, which catches wind.
  • Do not attach to a Colorbond or fibro fence without checking the manufacturer’s advice or asbestos risk; ask a contractor first.
  • If you rent, ask the landlord in writing before fixing anything to the fence, and use clips that leave no marks.

Fence post repair: leaning, rotten and cracked posts

Posts fail at ground level, where moisture sits against the timber, so look there first.

  • Probe the base with a screwdriver; if it sinks in easily, the timber is rotten and the post needs replacing.
  • For a post with a sound top and rotten base, a post-repair bracket or spur can save the job if the manufacturer allows it.
  • Dig out the old concrete carefully and set the new post in fresh concrete with a slight slope away from the post for drainage.
  • Use treated posts rated for ground contact, and check the label for the right grade for your soil.
  • Replace both posts either side of a failed panel if they are the same age, as the second one is usually close behind.
  • In older Inner West terraces, check whether the fence is on a shared boundary and talk to your neighbour before replacing it.

How deep should a fence post be?

Depth depends on fence height, soil type and wind exposure, so there is no single answer for every yard.

  • A common rule of thumb is to bury roughly one third of the post length (indicative — check with your supplier or a contractor).
  • Sandy or soft clay soil often needs deeper or wider footings than firm clay, so ask your local hardware store or fencing supplier.
  • Taller solid fences take more wind load, so they need deeper concrete footings than low picket fences.
  • Check the maker’s instructions for any pre-made panel system, which may specify its own post depth and spacing.
  • Slope the concrete top slightly above ground level so water runs off, rather than pooling against the timber.
  • Over $5,000 of residential building work needs a Building Commission NSW licence, so use a licensed fencing contractor for large jobs.

Common mistakes with fence repair

  • Fixing palings while the post still leans, so the repair loosens again after the first storm.
  • Using plain steel nails or screws that rust and stain the timber, instead of galvanised or stainless fixings.
  • Skipping props, which lets the panels fall and can injure whoever is holding the post.
  • Digging near the boundary without checking for cables and pipes, or ringing Dial Before You Dig for deeper work.
  • Cutting or drilling old fibro fence sheets in a pre-1990 home without checking for asbestos.
  • Replacing a shared fence without talking to your neighbour first, which can lead to a dispute over cost.

When to call a handyman or a licensed trade

  • You have more than one leaning or rotten post, which suggests the whole line is nearing the end of its life.
  • The fence is Colorbond, which belongs to a licensed Colorbond fencing contractor rather than a handyman.
  • The fence is a pool barrier, which has safety rules and needs a licensed professional or council advice.
  • Suspect fibro or sheeting is present in a pre-1990 home, in which case treat it as asbestos and call a licensed asbestos professional.
  • The job is valued at more than $5,000, so a Building Commission NSW licence is required; work under $20,000 uses a small jobs contract.
  • The fence has a tricky slope, retaining wall or neighbour dispute that needs a measured plan.

Cost to hire a handyman for fence repair in Sydney

Prices include GST and come from October 2026 Sydney handyman data; timber, concrete and fixings are extra.

JobLowTypicalHigh
Handyman hourly rate, Sydney$57$105$140
Call-out or minimum charge, Sydney$92$140$170
Half-day handyman, Sydney (4 hours)$230$415$645
Full-day handyman, Sydney (8 hours)$435$690$1025
  • A full day can cost less than eight hourly-billed hours, so a long list of fence and gate jobs often suits a day booking.
  • The maximum deposit before work starts is 10%, so be wary of anyone asking for more.

FAQ: fence repair

How to attach shade cloth to a fence?

Fix reinforced shade cloth to a sound fence with rust-proof clips or washers, spaced evenly along the top and bottom, and keep it taut but not overstretched. Repair leaning posts first, because the cloth catches wind like a sail. Follow the packet instructions and skip Colorbond and fibro.

How deep should a fence post be?

A common rule of thumb is about one third of the post length underground (indicative — check with your supplier or a contractor). Soft soil, tall fences and windy sites need more, and pre-made panel systems may specify their own depth, so read the maker’s instructions.

How much does fence repair cost in Sydney?

A Sydney handyman typically charges $105 an hour (range $57–$140) with a call-out or minimum of $140, plus materials. Small paling and gate fixes often fit in one visit, while several posts may suit a half-day booking at about $415.

Do I need a licence for fence repair?

Minor repairs by a handyman do not usually need one, but residential building work valued at more than $5,000 must be done by someone licensed by Building Commission NSW. Pool barriers and Colorbond fences should go to specialists.

Getting fence repair done in Sydney

If you would rather not prop panels and mix concrete, we can inspect the line, fix posts, palings and gates in one visit and flag anything that needs a specialist. Book a Sydney handyman for fence repair, and see our guides to building a fence, retaining wall cost, building a retaining wall and concrete driveway cost.