The floor sanding and polishing cost per square metre in Sydney typically runs from about $35 to $80 for a full sand and coat (indicative — get itemised quotes), with a light buff and recoat cheaper. Floor condition, the number of coats, any board repairs and the finish you choose drive the price.
This guide covers the cost of floor sanding, scratch repair, DIY sanding and how to compare quotes. For other floor types, see our carpet replacement cost guide.
Key points
- Range: roughly $35–$80 per m² for a full sand and polish in Sydney (indicative — get itemised quotes), with a recoat only at the lower end.
- Biggest cost driver: floor condition, because deep scratches, old coatings, gaps and nail heads add time and sandpaper.
- Cheapest option: a light scratch repair or buff and recoat, if the boards are sound and only the top coat is worn.
- DIY is possible with a hired sander, but a mistake can gouge the boards, so hire a floor specialist for valuable timber.
Floor sanding and polishing cost per square metre: price table
These ranges are a guide for Sydney homes, and the same room can differ by supplier and floor condition.
| Job | Per m² | Typical 20 m² room |
|---|---|---|
| Cost to sand and polish floorboards, full sand and coat | $35–$80 (indicative) | $700–$1,600 (indicative) |
| Cost of floor sanding only, no finish | $18–$40 (indicative) | $360–$800 (indicative) |
| Floor polishing cost, buff and recoat | $15–$35 (indicative) | $300–$700 (indicative) |
| Sanding back floorboards with repairs and gap filling | $50–$110 (indicative) | $1,000–$2,200 (indicative) |
| Timber floor scratch repair, spot job | Per job, not per m² | $150–$500 (indicative) |
- Each figure is indicative — get itemised quotes, as old floors with paint, glue or damage change the scope.
- Staining, extra coats and hard-wearing finishes add to the per m² cost.
Floor sanding and polishing cost per square metre by city
Sydney is usually the dearest capital, and you can see the same pattern in verified handyman rates.
| City | Sand and polish per m² | Handyman hourly rate (verified) |
|---|---|---|
| Sydney | $35–$80 (indicative) | $57–$140, typical $105 |
| Melbourne | $32–$75 (indicative) | $52–$125, typical $94 |
| Brisbane | $30–$70 (indicative) | Not in our data |
| Perth | $30–$70 (indicative) | Not in our data |
| Adelaide | $28–$65 (indicative) | Not in our data |
- City ranges are indicative — get itemised quotes, because most floor sanders quote the job on site.
What affects the cost of floor sanding
Two rooms the same size can price very differently, and these factors explain most of the gap.
- Floor condition: deep scratches, cupped boards and pet stains need heavier sanding and more repair time (indicative extra cost).
- Old finish: thick polyurethane or paint takes longer to remove than a bare or lightly coated surface.
- Board repairs: punching nail heads, filling gaps and replacing damaged boards add labour and materials.
- Number of coats: three coats cost more than two, but give a longer-lasting finish.
- Finish type: water-based finishes and oil-modified finishes differ in price, drying time and look.
- Access and furniture: moving heavy furniture and stairs add time, and some sanders charge extra for stairs.
Timber floor scratch repair: when you do not need a full sand
Many scratches are in the finish, not the timber, and can be fixed without sanding the whole floor.
| Problem | Fix | Who |
|---|---|---|
| Light surface marks in the coating | Clean, then buff and recoat the area | DIY or handyman |
| Wood floor scratch repair on a single board | Spot sand, fill, and recoat to blend | Handyman or floor specialist |
| Scratched timber floor repair across the room | Sand back and recoat the whole floor for an even finish | Floor sanding specialist |
| Deep gouge or damaged board | Fill or replace the board | Handyman or carpenter |
| Gaps between boards | Fill with a flexible timber filler, then recoat | Floor sanding specialist |
- Test any repair in a hidden spot first, because filler and finish can show a different colour.
- If the floor has black or brown adhesive, vinyl or old underlay beneath carpet in a pre-1990 home, treat it as asbestos until checked (asbestos.nsw.gov.au).
Floor sanding: DIY vs hiring a pro
A hired drum sander is powerful, and a moment’s hesitation can leave a ripple in the boards that is expensive to fix.
| Factor | DIY with hired sander | Hire a specialist |
|---|---|---|
| Cost | Hire, sandpaper and finish; lower upfront | Higher, with dust control and equipment included |
| Skill | Easy to gouge the boards if the machine is left down | Experienced operators keep the floor flat |
| Dust and fumes | You manage the dust, ventilation and the product label | Dust extraction and cleaner finishes |
| Finish | Good on a simple floor if you take your time | More consistent coats and edges |
| Warranty | Product warranty only | Workmanship warranty, in writing |
| Best for | Small rooms and plain boards | Large floors, stairs and good timber |
How to sand wooden floors step by step
This is the method a hired sander follows, and it explains why prep takes longer than the sanding itself.
- Clear the room and check the boards for nails, staples and carpet tacks; punch every nail head below the surface.
- Check the age of the home and any old coverings; if the home was built before 1990 and the material is unknown, stop and test for asbestos.
- Start with the coarsest paper the machine instructions suggest, sanding with the grain and keeping the sander moving at all times.
- Move to a medium and then a fine grade, vacuuming between passes so grit does not scratch the floor.
- Use an edge sander for borders and hand-sand corners, taking care around skirting and doors.
- Fill gaps and holes with timber filler, let it dry, then sand again lightly.
- Vacuum and wipe the floor, then apply the finish exactly as the product label says, keeping the room ventilated.
- Keep children and pets out until the finish has cured; call a vet if a pet breathes fumes or licks wet finish.
How to save on floor sanding without cutting corners
- Clear the room yourself so you are not paying labour to move furniture.
- Get at least three itemised quotes for the same number of coats and the same finish.
- Buff and recoat if the timber is sound and only the finish is worn, which costs less than a full sand.
- Fix loose boards and squeaks first, since sanding over movement hides nothing.
- Book the sander for a quiet season, and ask for a bundled price if you also need stairs done.
- Do not pay a large deposit; the maximum before work starts in NSW is 10%.
What a fair floor sanding quote should include
- Itemised materials: sandpaper grades, filler, stain and the exact finish, with the number of coats.
- Access and furniture: who moves the furniture and whether stairs are included.
- Waste removal: dust bags and old finish disposal, and a separate line for any suspect asbestos material.
- Warranty: workmanship warranty in writing, plus the product warranty from the maker.
- Licence number: residential building work valued at more than $5,000 must be done by someone licensed by Building Commission NSW.
- Contract terms: a small jobs contract applies under $20,000, and the maximum deposit is 10%.
FAQ: floor sanding cost
How much to sand and polish floorboards?
A full sand and polish typically costs about $35 to $80 per m² in Sydney (indicative — get itemised quotes), or roughly $700 to $1,600 for a 20 m² room. Repairs, extra coats and stairs add to the total.
How much does floor sanding cost without polishing?
Sanding alone typically costs about $18 to $40 per m² (indicative — get itemised quotes), though most people also pay for the finish because bare timber stains and wears quickly. Ask whether the quote covers edges and corners.
How much to polish floor boards if they are already sanded?
Buffing and recoating a sound floor typically costs about $15 to $35 per m² (indicative — get itemised quotes). It suits floors with worn finish but no deep scratches. A specialist can tell you on site whether a recoat will last.
How to sand wooden floors yourself?
Clear the room, punch nail heads, sand coarse to fine with the grain, edge and fill, vacuum, then apply the finish per the label. Hire a drum sander and keep it moving. If the home is pre-1990 and the floor covering is unknown, test for asbestos first.
Can a handyman repair floor scratches?
Yes for spot repairs and small boards, using filler and touch-up finish. A handyman charges about $105 an hour in Sydney (range $57–$140) with a call-out or minimum of about $140, and a floor specialist suits a full-room sand.
Getting floor sanding and scratch repair in Sydney
If you only need a scratched board fixed or a quote on the room, we can look at the floor and tell you what it needs. Book a Sydney handyman for repairs and quotes, and compare timber flooring cost, epoxy flooring cost and laminate vs hybrid flooring before you decide.


