How to fix squeaky floorboards: find the noisy board, locate the joist beneath it, then fix the board down with a screw or ring-shank nail, or work lubricant into the joint if it is rubbing. The biggest mistake is fixing into the gap beside a joist, which leaves the board loose and the squeak unchanged.
This guide covers how to fix squeaky floorboards step by step, how to stop squeaky floorboards from above and below, and what a Sydney handyman charges to do it.
Key points
- This is an eight-step job for most rooms, and each squeak takes a few minutes once you have found the board and the joist beneath it.
- A stud finder or a small drill with a pilot bit is the tool you cannot skip, because hitting pipes or cables under the floor is the main risk.
- Check for hidden pipes and cables before you fix anything, and treat old vinyl or floor coverings in a pre-1990 home as possible asbestos until checked.
- A Sydney handyman typically charges about $105 an hour (range $57–$140, October 2026), with a call-out of about $140 for a short visit.
Can you fix squeaky floorboards yourself?
Most squeaks are an easy DIY fix. Use this table to check your floor type first.
| Your situation | DIY OK? | Why |
|---|---|---|
| Timber floorboards with a bare floor above | Yes | You can fix the board down to the joist with a screw or ring-shank nail and fill the hole. |
| Carpeted floor | Yes, with care | Special squeak-fixing kits drive a screw through the carpet, but you need to find the joist first. |
| Access from underneath through a subfloor | Experienced DIYers | Working under the house is cramped and can hide pipes, wiring and pests, so take care or book a handyman. |
| Floor with a rumble, bounce or sag | Call a handyman | That points to a structural problem such as a rotten bearer or settled footing, not just a noisy board. |
| Pre-1990 home with old vinyl or sheet flooring | Check first | Floor coverings in homes built or renovated before 1990 are likely to contain asbestos, so check asbestos.nsw.gov.au before you drill or sand. |
| Floor over pipes, underfloor heating or cables | Check first | Underfloor plumbing, electrical and heating work belongs to licensed trades, so scan carefully and ask if unsure. |
| Rental property | Ask first | Fixing a floor changes the surface, so get your landlord’s written consent before you drill or fill. |
Tools and materials to fix squeaky floorboards
| Item | What it’s for | Tip |
|---|---|---|
| Stud or joist finder | Locates the joist and flags pipes and cables | Scan the area in both directions and mark the joist lines with painter’s tape before you fix anything. |
| Cordless drill and pilot bit | Drills a pilot hole so the board does not split | Choose a bit slightly smaller than the screw shaft, and countersink the head so it sits below the surface. |
| Floor screws or ring-shank nails | Pull the board tight to the joist | Check the packet for the right type for your floor, and avoid screws long enough to hit pipes. |
| Timber filler or wax | Hides screw heads and nail holes | Match the colour to your boards, and test it on an offcut or a hidden spot first. |
| Talcum powder or dry lubricant | Quietens boards that rub together | Brush it into the joint, then wipe off the surplus so it does not mark the finish. |
| Hammer and nail punch | Sets nail heads below the surface | Tap gently, and stop if the board begins to split. |
| Knee pads and torch | Protect your knees and light dark spaces | Use them for work in a low subfloor, and keep a second person nearby if you crawl under the house. |
How to fix squeaky floorboards: step by step
Work in daylight where you can, and have a second person walk the floor while you listen.
- Walk the room slowly, find each board that squeaks, and mark it with painter’s tape so you can find it again.
- Scan the area with a joist and pipe detector, and mark the joist lines and any pipes or cables in pencil.
- Check whether the board moves up and down on a joist or rubs against its neighbour, since each needs a different fix.
- For a board that rubs, brush talcum powder or a dry lubricant into the joint and work it in by walking over it.
- For a board that lifts, drill a small pilot hole through the board and into the centre of the joist you marked.
- Drive a screw or ring-shank nail in until the board is pulled snug to the joist, stopping when it is flush.
- Countersink the head slightly, then fill the hole with timber filler or wax that matches the board.
- Walk the floor again to check the squeak has gone, and repeat on any remaining boards, working along the joist line.
Fix creaky floorboards from below
If you can reach the underside of the floor safely, you can pull a loose board tight without marking the surface.
- Check the subfloor for clearance, damp, pests and rot before you crawl in, and keep a second person above who can hear you.
- Find the gap between the board and the joist, then slide a small timber shim or wedge into the gap with a dab of wood glue.
- Screw a short timber block alongside the joist to hold the board up, using screws short enough not to poke through the top.
- Do not drill into pipes or cables running through the joists, and stop if you find anything you cannot identify.
- Check for damp, rot or termite damage as you work, and book a licensed pest controller if you see signs of an infestation.
- Wear a dust mask and gloves, and avoid disturbing old insulation or sheeting in a pre-1990 home without checking it first.
Stop squeaky floorboards under carpet and tiles
Different floor coverings need different tricks, because you cannot see the board you are trying to fix.
- Use a squeak-fixing kit for carpet, which drives a screw through the carpet and snaps off the shaft below the pile.
- Mark the joist lines on the carpet with tape before you use the kit, because a screw that misses the joist does nothing.
- For floating floors, check the gap at the edges and the underlay, since the noise often comes from the boards rubbing at the perimeter.
- Leave tiled floors to a tiler or handyman, because a squeak under tiles may mean loose tile adhesive or a failing subfloor.
- Do not drill through tiles or waterproofed areas, and leave bathroom floors to a licensed waterproofer.
- If the squeak comes from a stair, check the treads and risers from below, and call a handyman if the stair feels loose.
Common mistakes when you fix squeaky floorboards
- Fixing into the gap beside a joist, so the board is only held by the flooring and the squeak returns within weeks.
- Skipping the pipe and cable scan, then driving a screw into a water pipe or live cable below the board.
- Using screws that are too long, which can hit services or poke through a ceiling underneath.
- Overtightening until the board dimples or splits, instead of stopping when the board is just snug.
- Drilling or sanding old floor coverings in a pre-1990 home without checking for asbestos first.
- Crawling under the house alone, when a second person could call for help if you are stuck or hurt.
When to call a handyman (or a licensed trade)
- The squeak comes with bounce, sag or a sloping floor, which suggests a structural problem that needs inspecting.
- You cannot find the joists or the floor is covered by tiles, a floating floor or thick underlay.
- There are pipes or cables under the floor, and you want a licensed plumber or electrician such as TQN Electrician to check them.
- You see damp, rot or termite damage, and you need a licensed pest controller and a builder to assess it.
- Your home was built or renovated before 1990 and the floor covering might contain asbestos.
- You are renting and want the repair done neatly, with your landlord’s written consent.
Cost to hire a handyman to fix squeaky floorboards in Sydney
Prices include GST and come from October 2026 Sydney data. There is no fixed price for squeaky floors, so use these handyman rates to estimate your job.
| Job | Low | Typical | High |
|---|---|---|---|
| Handyman hourly rate, Sydney | $57 | $105 | $140 |
| Call-out or minimum charge, Sydney | $92 | $140 | $170 |
| Half-day handyman, Sydney (4 hours) | $230 | $415 | $645 |
| Full-day handyman, Sydney (8 hours) | $435 | $690 | $1025 |
- A few squeaks in one room is usually a short job, while a whole house may be a half-day or full-day booking.
- A full day can cost less than eight hourly-billed hours, so ask for a day rate if you have a list of jobs.
- Bundle other small repairs into the visit, such as cracked tile repair or replacing skirting boards.
FAQ: how to fix squeaky floorboards
How to fix squeaky floorboards?
Find the noisy board, mark the joist beneath it and scan for pipes. If the board rubs, brush talcum powder or a dry lubricant into the joint. If it lifts, drill a pilot hole into the joist and drive a screw or ring-shank nail until snug, then fill the hole.
What causes floorboards to squeak?
Boards squeak when they rub against each other or move up and down on a joist, often because timber has dried, shrunk or loosened over time. Settling footings and worn nails can also let boards move, and a bounce or sag may point to a bigger problem.
Can you fix squeaky floorboards under carpet?
Yes. Locate the joist with a detector, mark it on the carpet, then use a squeak-fixing kit that drives a screw through the carpet and snaps off below the pile. Check for pipes and cables first, and follow the kit’s instructions.
Is lubricant or powder enough to stop a squeak?
It can quieten boards that rub together, but it will not fix a board that lifts off a joist. Try powder or dry lubricant first, then screw or nail the board down if the noise returns, and book a handyman if it keeps coming back.
Getting your floorboards fixed in Sydney
If you would rather not hunt for joists, we can find the noisy boards, scan for services and silence them in one visit. Book a Sydney handyman and add other small repairs. For related fixes, start with the toilet seat replacement guide.


