How to remove skirting boards: score the paint line, slide a thin bar behind the board with a scrap of timber to protect the wall, ease each board off in small steps, and pull the nails out from behind. The most common failure is levering straight against the plasterboard, because it crumbles and turns a simple swap into a patching job.
This guide covers how to remove skirting boards, how to install skirting boards, what skirting is, the tools you need, and what a handyman charges in Sydney if you’d rather hand it over.
Key points
- Plan on ten steps per room, and work slowly at the removal stage, since a clean removal makes the fit of the new boards much easier.
- A sharp utility knife and a flat bar are the tools you can’t skip, because a scored paint line stops the wall paint from tearing off with the board.
- If your home was built or renovated before 1990, check the NSW asbestos guidance before you cut, sand or pry old sheeting or boards behind the skirting.
- A Sydney handyman typically charges about $105 an hour (range $57–$140, October 2026), with a minimum charge of about $140 per visit.
How to remove skirting boards: can you DIY it?
A single room is a fair weekend job for a confident DIYer, and the risk sits with old homes and what lies behind the board.
| Your situation | DIY OK? | Why |
|---|---|---|
| Modern MDF or pine skirting on plasterboard | Yes | Boards are nailed or glued, and a careful lever lifts them without major damage. |
| Solid timber skirting in an older Sydney home | With care | Boards are thick, often painted many times and sometimes fixed to brick, so removal is slower. |
| Home built or renovated before 1990 | Check first | Wall sheeting, floor coverings and paint layers may contain asbestos, so don’t cut, sand or break suspect material. |
| Skirting hiding cables or pipes | Stop and check | Data, power or plumbing sometimes runs behind skirting, and cutting through it is dangerous. |
| Brick or concrete wall behind the skirting | Yes, but harder | Boards may be glued or plugged, and you need the right bits and fixings to refit. |
| You’re renting | No | Replacing skirting is more than a minor change, so get written consent from the landlord first. |
| New power points or switches in the new skirting | No | Moving or adding power points is licensed electrical work in NSW. |
What is skirting? Terms and parts
| Term | Meaning | Why it matters |
|---|---|---|
| Skirting board | The board along the base of an interior wall, where the wall meets the floor | It hides the gap, protects the wall from knocks and tidies the finish. |
| Architrave | The trim around door and window openings | It meets the skirting at the door, so the two profiles should match. |
| Scotia or quad | A small moulding at the foot of the skirting on some floors | It covers a gap above the floor and may need to come off first. |
| Mitre and scribe joints | Angled cuts for external corners and profiled cuts for internal corners | They decide how tight and neat the corners look once painted. |
| MDF, pine and hardwood | The most common skirting materials in Australian homes | The material affects cost, strength, moisture resistance and how it cuts. |
Tools and materials to remove and install skirting boards
| Item | What it’s for | Tip |
|---|---|---|
| Utility knife | Scores the paint and caulk line | Cut along the top and the ends so the wall paint does not peel off with the board. |
| Flat bar and scrap timber | Levers the board off the wall | Put the scrap behind the bar so the force spreads across the wall rather than a single point. |
| Hammer and nail punch | Removes and sinks nails | Pull nails back through the board’s rear, not through the face. |
| Stud finder with cable detection | Finds framing, wiring and pipes | Scan the wall before you pry or fix, because power often runs near the floor. |
| Mitre saw or mitre box | Cuts clean angles | Label each board and cut a spare piece to test the corner first. |
| Construction adhesive, nails and filler | Fixes and finishes the new boards | Use products suited to your wall, and follow the manufacturer’s instructions. |
| Safety glasses, gloves and mask | Protect you from dust and splinters | Wear them when you cut, pry or sand. |
How to remove skirting boards: step by step
Remove only the boards you need to, and work from a corner or a door end.
- Check the age of the home and the NSW asbestos guidance, and stop if you suspect old sheeting or flooring behind the board.
- Scan the wall for cables and pipes near the floor, and turn off power at the board if any outlets sit in the skirting zone.
- Score the top edge and the ends of the board with a sharp knife, cutting through paint and caulk to the surface.
- Slide the flat bar into the gap, place a scrap of timber behind it, and lever gently at the nail positions.
- Work along the board in small moves rather than one big pull, and stop if the wall starts to crumble.
- Remove the board, pull the nails through from behind, and remove any glue lumps with a scraper or chisel.
- Number each board on its back, measure the wall carefully, and mark the new lengths with a pencil.
- Cut the new boards with correct mitres and scribed joints, test-fit them, and adjust before fixing anything.
- Fix the new boards with adhesive and nails into the studs or plugs, keeping the top edge straight with a level.
- Fill the nail holes, seal the top and the corners with flexible caulk, and paint once everything is dry.
How to install skirting boards
New boards sit best when the wall and floor are clean and the corners are cut to the room, not to the plan.
- Dry-fit every board before gluing, and check that the top edge runs straight along the wall with a level.
- Cut internal corners with a scribe joint and external corners with a mitre, practising on offcuts first.
- Fix to the studs or plugs along the board’s length, using the fixings recommended by the manufacturer.
- Leave a small expansion gap where the maker recommends, and cover it with a scotia or flexible sealant.
- Prime and paint timber or MDF before or after fixing, and seal cut ends well, since moisture swells them.
- Read our how to tile guide if the skirting meets tiled floors, where a tiled skirting or a gap may suit better.
Replacing skirting boards in bathrooms, laundries and wet areas
Wet areas behave differently, and moisture is the problem that skirting usually points to.
- Choose moisture-resistant boards or tiles for wet areas, because plain MDF swells and falls apart when it gets damp.
- Check for rot, mould and damp behind the board before you cover it, and fix the cause first.
- Do not damage a waterproof membrane, and book a licensed plumber or waterproofer for any membrane repair.
- Seal the gap at the floor with a flexible sealant rather than rigid filler, which cracks as the floor moves.
- Treat wet-area linings and floor coverings in pre-1990 homes as possible asbestos until checked.
- Look at our cracked tile repair guide if tiles beside the skirting are damaged.
Common mistakes when you remove skirting boards
- Levering straight against the plasterboard with no scrap timber, which crushes the wall and leaves a patch to repair.
- Skipping the cable and pipe scan, then cutting or nailing into wiring or plumbing near the floor.
- Not scoring the paint line, so the paint and the wall’s paper face tear off with the board.
- Cutting corners by eye without a level or test pieces, which leaves gaps that filler can’t hide.
- Sanding or breaking old boards, sheeting or floor coverings in a pre-1990 home without checking for asbestos.
- Working alone with long, heavy boards, which swing and damage walls and ceilings as you cut and fit them.
When to call a handyman to replace skirting boards (or a licensed trade)
- The home is pre-1990 and you are unsure what sits behind the old skirting or under the floor covering.
- The walls are brick, rendered or crumbling, and need patching or special fixings before new boards go on.
- You want power points or switches moved or added in the skirting zone, which needs a licensed electrician such as TQN Electrician.
- You find damp, mould or pipes behind the board, and need a licensed plumber such as TQN Plumber.
- You are replacing skirting through several rooms, where accurate mitres and long runs save hours.
- You want the painting done as part of the job, and need a painter from TQN Construction.
Cost to replace skirting boards in Sydney
Prices include GST and come from October 2026 Sydney handyman data. There is no fixed rate for skirting, so quotes depend on the length, the material and the wall.
| Job | Low | Typical | High |
|---|---|---|---|
| Handyman hourly rate, Sydney | $57 | $105 | $140 |
| Call-out or minimum charge, Sydney | $92 | $140 | $170 |
| Half-day handyman, Sydney (4 hours) | $230 | $415 | $645 |
| Full-day handyman, Sydney (8 hours) | $435 | $690 | $1,025 |
| Minor plastering or patching, Sydney (per job) | $140 | $230 | $575 |
- A single room usually fits in a half-day, while a whole floor suits the full-day rate.
- Materials and painting are usually extra, so ask for boards, adhesive and finish to be itemised.
- Patching of wall damage from removal is a separate line, and the wide range reflects the scope.
FAQ: how to remove skirting boards
How to remove skirting boards without damaging the wall?
Score the paint line with a knife, then slide a flat bar behind the board with a scrap of timber against the wall. Lever gently at each nail in small moves. Check the home’s age first, because old sheeting in a pre-1990 home may contain asbestos.
How to install skirting boards?
Measure each wall, cut internal corners with a scribe and external corners with a mitre, and test-fit before fixing. Fix with adhesive and nails into studs or plugs, keep the top edge level, fill the holes, seal the gaps and paint when everything is dry.
What is skirting?
Skirting is the board that runs along the bottom of an interior wall where it meets the floor. It covers the join, protects the wall from knocks and vacuum damage, and tidies the finish. The profile, height and material vary with the age and style of the home.
Can you replace skirting boards without removing the old ones?
Sometimes you can fix new boards over the old ones, but the room loses depth and the profile can look bulky. Door architraves may not line up either. For a neat result, remove the old boards first, and check the wall behind them.
Getting your skirting boards replaced in Sydney
If you’d rather not work out how to remove skirting boards around cables and corners, we can remove, cut, fit and finish them in one visit. Book a handyman in Sydney and add small jobs such as wallpaper removal or a toilet seat replacement.


