How to remove mould from silicone: ventilate the room, apply a mould remover made for bathrooms exactly as the label says, scrub gently with a soft brush, rinse and dry. If black stains sit deep in the bead, the mould has grown through the silicone and the only fix is to cut it out and reseal.
This guide covers how to get mould out of silicone safely, the cleaners to use and never mix, how to stop it returning, and what a Sydney handyman charges for resealing.
Key points
- Light surface mould usually clears in about six steps, but black staining that runs through the bead means the silicone must be replaced.
- A soft brush and a label-approved mould remover are the two things you cannot skip, and you should never mix cleaning products.
- Ventilate the room, wear gloves and eye protection, and check older wet areas for asbestos before scraping or cutting anything.
- A Sydney handyman typically charges about $205 for weatherproofing or resealing work (range $115 to $345, October 2026), plus a call-out or minimum from $92.
Can you remove mould from silicone yourself?
Yes, for light mould on the surface. Use this table to decide between cleaning and replacing the bead.
| Your situation | DIY OK? | Why |
|---|---|---|
| Light speckles or pink and grey film on the surface | Yes | Surface mould lifts off with a bathroom mould remover and a soft brush, following the label. |
| Black stain that stays after cleaning | Replace instead | Mould that has grown into the silicone cannot be scrubbed out, so cut the bead out and reseal it. |
| Silicone peeling, cracked or shrunk from the joint | Replace instead | A failed bead lets water behind the tiles, so cleaning only hides the problem for a short time. |
| Mould also on grout, ceiling or behind tiles | Check first | Widespread mould usually points to poor ventilation or a hidden leak, and a leak needs a licensed plumber. |
| Pre-1990 home with old wet-area linings or floor coverings | Check first | Homes built or renovated before 1990 are likely to contain asbestos, so identify suspect material before you scrape or cut near it. |
| You have asthma or sensitive lungs | Take care | Cleaning products and mould spores both irritate airways, so ventilate well or have someone else do the job. |
| You are renting | Report first | Mould and failed seals are maintenance issues, so tell the landlord or agent in writing before you start. |
Tools and materials to remove mould from silicone
| Item | What it is for | Tip |
|---|---|---|
| Bathroom mould remover | Kills and lifts surface mould | Use a product made for bathrooms from Bunnings or a supermarket, and follow the label for contact time and safety. |
| Soft brush or old toothbrush | Scrubs the bead gently | Avoid stiff wire brushes, because scratches in the silicone give mould more places to grip. |
| Rubber gloves and eye protection | Protects skin and eyes | Wear them even for mild products, since splashes in a small bathroom are common. |
| Microfibre cloths | Wipes and dries the area | Dry the joint fully afterwards, because damp silicone invites the mould back. |
| Silicone removal tool and new silicone | Cuts out and replaces a stained bead | Choose a mould-resistant bathroom silicone from brands like Selleys, Sika or Bostik and follow the cartridge instructions. |
| Fan or open window | Clears fumes and moisture | Run the exhaust fan or open the window before, during and after cleaning. |
How to remove mould from silicone: step by step
- Open the window or switch on the exhaust fan, put on gloves and eye protection, and keep other people and pets out of the room.
- Wipe the bead with warm soapy water and a cloth to remove soap scum, which feeds mould and blocks cleaners from reaching it.
- Apply a bathroom mould remover along the silicone, following the label for dilution, contact time and whether you must rinse first.
- Never mix cleaning products, especially bleach with vinegar or ammonia, because the fumes can be dangerous in a small bathroom.
- Scrub gently along the joint with a soft brush, working in short strokes, and reapply to stubborn spots if the label allows.
- Rinse thoroughly with clean water, wipe dry with a microfibre cloth, and leave the fan running until the joint is completely dry.
- Check the result in good light, and decide whether the bead is clean, faded or still stained black through its full depth.
- Cut out and reseal the bead if staining remains, following our guide to removing silicone and guide to siliconing a shower.
How to get mould out of silicone on tiles, glass and baths
The surface decides the method, and Sydney bathrooms with older tiled showers often have mould in the corners first.
- On glazed tiles, clean the silicone first, then check the grout lines separately using our how to clean grout guide.
- On glass screens, keep cleaner off the metal frame seals, as some products dull or mark aluminium.
- On acrylic or fibreglass baths, check the product label first, since some mould removers can cloud or etch soft surfaces.
- On natural stone, avoid acidic or harsh cleaners and test a hidden spot first, because stone stains and etches easily.
- Around taps and drains, wipe off soap and shampoo residue, because trapped moisture there makes mould return quickly.
How to get rid of mould in shower silicone for good
Once the bead is clean or replaced, the goal is keeping moisture off it.
- Run the exhaust fan during every shower and for a while afterwards, according to what suits your bathroom.
- Squeegee the walls and wipe the corners after showering, because standing water is what mould needs.
- Reseal tired silicone once it has cracked, shrunk or pulled away, instead of waiting for black stains to appear.
- Choose a bathroom silicone rated for wet areas and let it cure fully, following the manufacturer’s instructions, before using the shower.
- Consider a fresh grout job where grout is failing too, using our guides on shower regrouting and how to grout tiles.
Common mistakes when you remove mould from silicone
- Mixing bleach with vinegar, ammonia or other cleaners in a closed bathroom, which can create toxic fumes.
- Ignoring the product label, then using too much, too little or leaving it on far longer than it allows.
- Scrubbing hard with abrasive pads that scratch the silicone and give mould a rougher surface to cling to.
- Applying new silicone over old mouldy silicone, which fails quickly because the new bead cannot bond properly.
- Scraping or cutting near old wet-area sheeting in a pre-1990 home without checking asbestos.nsw.gov.au first.
- Treating spreading mould as a cleaning problem when it is really a leak or a ventilation fault.
When to call a handyman (or a licensed trade)
- The silicone is black right through, cracked or peeling, and the bead needs cutting out and replacing properly.
- You suspect water is getting behind tiles or into the lining, which can need a licensed waterproofer or plumber.
- Mould is on a ceiling or wall beyond the shower joint, which points to ventilation or a leak.
- The bathroom was built or renovated before 1990 and you are unsure what the lining or floor covering contains.
- You are renting and want the repair documented and done neatly for the landlord or agent.
- You would rather use a fixed price than risk a messy bead that has to be done twice, so you book the job.
Cost to remove mould from silicone and reseal in Sydney
Prices include GST and come from October 2026 Sydney handyman data. Cleaning alone is a minimum-charge job, while a full reseal sits in the weatherproofing range.
| Job or charge | Low | Typical | High |
|---|---|---|---|
| Weatherproofing or caulking (resealing), Sydney | $115 | $205 | $345 |
| Call-out or minimum charge, Sydney | $92 | $140 | $170 |
| Handyman hourly rate, Sydney | $57 | $105 | $140 |
| Half-day handyman, Sydney (4 hours) | $230 | $415 | $645 |
- The minimum charge applies even for a five-minute fix, so combine resealing with other small jobs in one visit.
- Ask whether the quote includes removing the old bead, cleaning the joint and the cost of the silicone.
- Our epoxy grout guide and grout types and colours guide help you plan a bigger bathroom refresh.
FAQ: how to remove mould from silicone
How to remove mould from silicone safely?
Ventilate the room, wear gloves and eye protection, and apply a bathroom mould remover as the label directs. Scrub gently with a soft brush, rinse and dry. Never mix cleaning products. If staining remains inside the bead, replace the silicone.
How to get mould out of silicone that has turned black?
Black staining often means mould has grown through the silicone. A cleaner may fade the surface, but it rarely reaches the full depth. Cut out the old bead, clean and dry the joint, and apply fresh mould-resistant silicone.
How to get rid of mould in shower silicone before it comes back?
Keep the area dry. Use the exhaust fan, squeegee after showers, and wipe corners. Replace silicone that has cracked or peeled, and fix leaks or poor ventilation. A clean, well-cured bead resists mould far longer than old, damaged silicone.
Can you paint or cover mouldy silicone?
No. Mould keeps growing underneath and shows through. Silicone does not take paint well either. Clean and replace the bead instead, and have a handyman do it if the joint is wide, awkward or near old wet-area linings.
Getting mouldy silicone fixed in Sydney
If scrubbing has not worked, we can cut out the old bead, clean the joint and reseal it neatly in one visit. Our handymen bring the right tools and silicone for wet areas. Book a handyman in Sydney for silicone and regrouting, and bundle any other small jobs on the same booking.


