Can you tile over tiles? Yes, when the old tiles are flat, sound and firmly bonded: clean and prime them, then fix the new tiles with a suitable adhesive. The biggest thing that goes wrong is a hidden problem underneath, such as hollow tiles, a failed waterproof membrane or asbestos in an old pre-1990 floor, so test before you buy a single box.
Key points
- Difficulty is moderate and the job runs to 8 steps, with the prep stage taking more of your time than the tiling itself.
- The one tool you cannot skip is a long straightedge or level, because tiling over a surface that is not flat only copies the problem upward.
- Homes built or renovated before 1990 are likely to contain asbestos in wet-area linings and floor coverings, so identify suspect material before you disturb it.
- A Sydney handyman charges $57–$140 an hour (typical $105) incl GST, and a call-out or minimum charge of $92–$170 (typical $140).
Can you tile over tiles yourself?
Sound, dry floors and walls in dry rooms are realistic DIY; wet areas and unknown substrates are where homeowners get caught.
| Situation | DIY OK? | Why |
|---|---|---|
| Dry room, tiles tap solid and sit flat | Yes | Nothing is moving underneath, so a keyed surface and the right adhesive will hold. |
| Tiles sound hollow or rock when you tap them | No | The bond has failed, so new tiles will fail too; the old layer has to come off. |
| Shower, bathroom floor or laundry | Handyman or trade | The waterproof membrane sits under the old tiles; book a licensed plumber or waterproofer before building on it. |
| Pre-1990 house, unknown floor covering or lining | Test first | Treat suspect material as asbestos; do not sand, grind or drill it, and check asbestos.nsw.gov.au. |
| Renting the property | Ask first | New tiles are a permanent change, so you need the landlord’s written consent. |
| Large floor area or low door clearances | Handyman | The added build-up affects doors, thresholds and appliances, which is easier to plan with a site visit. |
Tools and materials for tiling over tiles
Most items are available from Bunnings, and the adhesive maker’s data sheet decides the details.
| Item | What it is for | Tip |
|---|---|---|
| Long straightedge or level | Checking the old surface is flat before you start | Mark high and low spots with a pencil so you can grind or fill them. |
| Degreaser and stiff brush | Removing soap, oil and wax from the old glaze | Rinse well; a greasy surface stops primer and adhesive bonding. |
| Bonding primer | Giving the glazed tile a surface the adhesive can grip | Use the product the adhesive maker (Ardex, Mapei) recommends for glazed tile. |
| Flexible tile adhesive | Fixing the new tiles to the primed surface | Check the packet for tile type, coverage and working time; do not guess. |
| Notched trowel and spacers | Spreading adhesive evenly and keeping joints consistent | Trowel size follows the tile size, so read the adhesive instructions. |
| Dust mask, glasses and gloves | Protecting you while cleaning and cutting | Wet-cut where possible to keep silica dust down. |
Can you tile over tiles: step by step
Follow the packet instructions for every product, because adhesive and primer systems differ between brands.
- Tap every old tile with a coin or screwdriver handle; mark any that sound hollow, and remove and re-bed those before going further.
- Check for asbestos risk if the home is pre-1990, and stop if floor coverings or linings under the tiles look suspect.
- Hold the straightedge across the floor or wall in several directions and mark every high or low spot you find.
- Grind or fill the marked spots with a levelling product recommended for the surface, then let it set as the packet directs.
- Scrub the whole surface with degreaser, rinse with clean water, and let it dry fully so no moisture or soap film remains.
- Apply the bonding primer in an even coat, keeping to the manufacturer’s spread rate and the drying time on the tin.
- Spread adhesive with the notched trowel in small sections, press each tile into place, and check level and spacing as you go.
- Grout once the adhesive has cured as the packet specifies, then seal joints at corners and edges with flexible silicone, not grout.
Can you put floorboards over tiles?
Yes, floating floors and some engineered timber can go over tiles, but the tile surface has to be flat and the product has to allow it.
- Check the flooring maker’s installation sheet first, because some floating systems accept a tiled base and others require it to be removed.
- Lay a suitable underlay across the tiles, which also softens the hard feel and helps deaden impact sound.
- Deep grout lines or lippage between tiles will telegraph through, so fill and level the joints before laying.
- Never nail or screw through tiles on a slab or wet area without advice, because you may hit a membrane, pipe or hydronic coil.
- Allow for the extra height at doors, skirting boards and kitchen kickboards, and see our skirting board replacement guide.
- Avoid solid timber glued over tiles in damp areas, since moisture can cup the boards.
Tiling over tiles in a rental or wet area
These two settings carry the most risk, so slow down and get approvals or advice before you start.
- In NSW a landlord cannot unreasonably refuse certain minor changes, but fixed tiling is not on that list, so get written consent before you start.
- Never tile over a leaking shower or bathroom floor: find the leak, and book a licensed plumber because waterproofing and drain work is licensed.
- If tiles are cracked rather than loose, our cracked tile repair guide shows when a patch beats a re-lay.
- If the substrate has cracks that move, fix the cause first; a hairline crack in a slab can reopen through new tiles, as our concrete crack repair guide explains.
- Build-up around a bath, toilet pan or shower screen can leave these fittings sitting too low, so measure before ordering.
- Use flexible silicone at wall-to-floor junctions and around fixtures so normal movement does not crack the grout.
Common mistakes when you tile over tiles
- Skipping the tap test, so hollow tiles stay under the new layer and pop loose months later.
- Tiling over an uneven surface, then fighting lippage at every joint when the straightedge would have shown the problem.
- Applying adhesive straight onto glazed tile with no primer, when the manufacturer’s instructions call for a bonding coat.
- Ignoring asbestos in a pre-1990 home, and grinding or drilling old floor coverings or linings before checking.
- Forgetting door clearances, thresholds and fixture heights, so new tiles stop doors swinging or leave a toilet too low.
- Lifting heavy tile boxes alone, when a second person makes the job safer for your back.
When to call a handyman (or a licensed trade)
- You are unsure whether the substrate is sound, flat or hiding an old membrane, and want a second opinion before you buy tiles.
- The floor or wall is a wet area, where waterproofing must be done by a licensed plumber or waterproofer.
- The house is pre-1990 and you suspect asbestos in floor coverings or linings, which needs testing and licensed removal, never DIY.
- The job needs new power points or fan wiring, which requires a licensed electrician regardless of cost.
- The total job value passes $5,000, when residential building work must be done by someone licensed by Building Commission NSW.
- You want straight lines, cuts and a warranty on a large floor and would rather not carry and cut the tile yourself.
Cost to hire a handyman for tiling over tiles in Sydney
Prices include GST and come from October 2026 Sydney handyman data; tiling itself is quoted per job after a site visit.
| Job | Low | Typical | High |
|---|---|---|---|
| Handyman hourly rate, Sydney | $57 | $105 | $140 |
| Call-out or minimum charge | $92 | $140 | $170 |
| Half-day handyman (4 hours) | $230 | $415 | $645 |
| Full-day handyman (8 hours) | $435 | $690 | $1025 |
| Weatherproofing or caulking (resealing around fixtures) | $115 | $205 | $345 |
| Minor plastering or patching (wall repairs before tiling) | $140 | $230 | $575 |
- A full day can cost less than eight hourly-billed hours, so a whole bathroom floor often suits a day booking.
- Ask for an itemised written quote that separates prep, tiling, grout and silicone.
FAQ: can you tile over tiles
Can you tile over tiles?
Yes, if the old tiles are firmly bonded, flat and clean, and you prime them and use an adhesive suited to the new tile. Remove any hollow or cracked tiles first. In wet areas the waterproofing underneath has to be sound, so a licensed plumber should check it before you build on top.
Can you put floorboards over tiles?
Often yes, using a floating floor or engineered boards with a suitable underlay, provided the tiles are flat and the flooring maker’s instructions allow it. Fill deep grout lines so they do not telegraph through. Check door clearances and skirting heights, and avoid fixing through tiles without advice.
Will tiling over tiles raise the floor height?
Yes, because you add the thickness of primer, adhesive and the new tile. That affects door swing, thresholds, skirting and fixtures such as toilets and baths. Measure the clearances before you buy, and check the adhesive packet for the layer thickness it expects.
Can you tile over tiles in a shower?
Only if the existing waterproofing is intact and the tiles are sound, and that is hard to confirm without opening the wall. Waterproofing is licensed work, so book a licensed plumber or waterproofer to assess it. In most failed showers the old layer has to come out.
Getting tiling over tiles done in Sydney
If you would rather have the prep and tiling done properly, we can inspect the surface, flag anything that needs a licensed trade and quote it in writing. Book a Sydney handyman for small tiling repairs and finishing, and see our how to tile guide for the full method, plus replacing a toilet seat, tightening a toilet seat and removing wallpaper for other small bathroom jobs.


