Epoxy grout is a two-part resin grout that cures hard, waterproof and stain-resistant, which makes it a strong choice for showers, kitchen splashbacks and benchtops. It costs more than cement grout and sets quickly, so it rewards preparation and punishes rushing.
This guide explains what epoxy grout is, how it compares with cement grout, what it costs in Sydney, how to choose a colour, how to grout and regrout tiles, and how to seal and maintain the result.
Key points
- Epoxy grout resists water, stains and mould far better than standard cement grout, which is why it suits showers and splash zones.
- It typically costs two to four times more than cement grout in materials, and it is harder to apply and clean up (indicative — get itemised quotes).
- Regrouting a shower is achievable for a patient DIYer, but waterproofing faults and pre-1990 wall linings are jobs for licensed trades.
- A Sydney handyman charges about $57 to $140 per hour, and resealing silicone around a shower often sits near $205 per job.
What is epoxy grout?
Epoxy grout is made from epoxy resin and a hardener, usually with fine filler and colour. Unlike cement grout, it does not absorb water, so it needs no sealer once it has cured.
Many Sydney bathrooms we visit have cement grout that has gone grey and grown mould in the corners, and epoxy is the usual upgrade for a wet area that has to stay clean.
- Composition: two or three parts, a resin, a hardener and a filler or colour pack, mixed on site just before use.
- Water absorption: close to none, so it does not stain from soap, shampoo or hair dye the way porous cement grout does.
- Working time: short once mixed, so you grout small sections and clean as you go, following the packet instructions.
- Safety: wear gloves and eye protection, ventilate the room and follow the safety data sheet, as the uncured resin irritates skin.
- Cure and use: it needs time to reach full strength, so keep the shower dry until the manufacturer says it is ready.
Types of epoxy grout
Not every epoxy grout behaves the same, so match the product to the job. The bands below are indicative, and the packet tells you the real coverage and cure time.
| Type | Best for | Lifespan and strength | Price band |
|---|---|---|---|
| Standard two-part epoxy | Showers, kitchen splashbacks and commercial-style benchtops | Very hard and long lasting; resists stains and chemicals | Mid to high (indicative) |
| Epoxy-modified cement grout | Floors and showers where you want easier handling | Tougher than standard cement; more flexible than pure epoxy | Low to mid (indicative) |
| Premium colour-stable epoxy | Light colours and feature tiles that must not yellow or fade | Holds colour well, with a cleaner finish on glass mosaics | High (indicative) |
| Cement grout, for comparison | Dry areas, tight budgets and quick DIY jobs | Absorbs water and needs sealing; stains and cracks sooner | Low (indicative) |
Compare grout types and colours
Colour changes how clean a bathroom looks, and our guide to grout types and colours compares cement, epoxy and urethane in more detail.
- Light greys such as misty grey and mystic grey hide soap film better than white, and they suit most white or stone-look tiles.
- Products like Ultracolor Plus, Ardex Alabaster and Kerakoll ranges list their colours on a manufacturer chart, so match the name against the chart, not a phone photo.
- Buy a small sample and test it on a spare tile, because grout looks darker when wet and lighter once fully cured.
Epoxy grout cost in Sydney
Epoxy grout costs more in materials and labour than cement grout. These are indicative ranges for a standard bathroom, so get itemised quotes before you commit.
| Item | Materials | Installed by a pro |
|---|---|---|
| Epoxy grout kit for a small shower | $60–$180 (indicative) | Often included in the job price |
| Cement grout bag for comparison | $10–$40 (indicative) | Often included in the job price |
| Regrout a shower floor and walls with epoxy | $100–$300 (indicative) | $600–$1,800 (indicative) |
| Regrout a small splashback or vanity | $40–$120 (indicative) | $250–$700 (indicative) |
| Reseal shower silicone (caulking) | $15–$40 (indicative) | $115–$345, with about $205 typical |
| Handyman labour, Sydney | Not applicable | $57–$140 per hour, with call-out from $92 to $170 |
- Tile size and joint width: narrow joints on large tiles use little grout, while wide joints on mosaics use a lot more.
- Removing old grout: hard cement grout takes time to rake out, and extra hours move the price up (indicative — get itemised quotes).
- Access and condition: cracked tiles, hollow tiles or failed waterproofing change the job from regrouting to a repair.
- Waterproofing: any wet-area membrane fault belongs to a licensed waterproofer, and that cost sits outside a normal regrout.
- Pre-1990 homes: old wet-area linings or adhesive may contain asbestos, so check asbestos.nsw.gov.au and treat suspect material as asbestos before anyone grinds or cuts.
Epoxy grout pros and cons
Epoxy is not always the right call. Weigh these lists against your budget, your patience and the tiles you have.
- Pro: It resists water, stains, mould and household chemicals better than cement grout, so showers stay cleaner for longer.
- Pro: It needs no sealer once cured, which saves a yearly chore and the risk of missing a joint.
- Pro: It stays strong in high-traffic areas and bathroom floors where cement grout crumbles at the edges.
- Pro: It holds colour well in many products, so a pale grout line stays crisp for years.
- Pro: It suits glass and stone mosaics, as long as the manufacturer confirms compatibility.
- Pro: Many products are low in shrinkage, so joints are less likely to open up with movement.
- Con: It costs more than cement grout, both for materials and for a tradesperson’s time (indicative — get itemised quotes).
- Con: Its working time is short, so one mistake in a big shower can set hard before you fix it.
- Con: Cleaning off the haze is harder, and rushing leaves a film that needs special cleaners.
- Con: It is difficult to remove later, so a poorly applied job is a bigger headache than cement.
- Con: Fumes and skin contact need care, and you must read the label and safety data sheet.
- Con: It can look glossy or slightly plastic on some matt tiles, so test a sample first.
How to choose epoxy grout for a shower
Showers are the best use for epoxy grout. Work through this checklist before you buy anything.
- Confirm the surface is a sound, waterproofed wet area, because grout is not the waterproofing layer and cannot fix leaks behind the tile.
- Check the joint width and tile type against the packet, since some products suit narrow joints only and others suit wide ones.
- Pick a colour from the manufacturer’s chart and test it on a spare tile, avoiding pure white if you dislike cleaning.
- Choose a product from an established brand such as Mapei, Ardex or Kerakoll, and read the stated working time and cure time.
- Buy the right tools: a rubber grout float, a tile grout brush, sponges, spare buckets and a low-speed mixer paddle.
- Decide whether you will do it yourself or book a pro, based on how many square metres of tile and how long you can keep the shower out of use.
How to grout tile with epoxy grout
Learning how to grout tile with epoxy grout comes down to working in small sections. Our guide to grouting tiles covers cement grout and general technique in full.
- Clean the joints of dust, adhesive and old sealer, and let the tile adhesive cure fully before you start.
- Mask the edges, then mix the parts exactly as the packet says, using a low-speed mixer so you do not whip in air.
- Press the grout into the joints with a rubber float held at an angle, and work in a small area only.
- Scrape the surface clean and wipe diagonally with a damp sponge, rinsing often and changing the water.
- Remove the haze while it is still soft, using the cleaner the manufacturer recommends, and avoid scrubbing the joints.
- Keep the area dry and untouched for the cure time on the packet; how long grout takes to dry varies by product and room conditions.
- Grout mixer and pump: a low-speed paddle on a drill mixes small batches, and a grout pump or bag suits wide joints on floors (indicative — check the product guide).
- Tile grout brush: use a stiff nylon brush to clean joints before grouting, never a wire brush that scratches glazed tiles.
How to regrout tiles in a shower: can you regrout tiles yourself?
Yes, you can regrout tiles, and is it hard to regrout a shower is a fair question. The work is fiddly rather than difficult, and the hardest part is removing the old grout. Read our shower regrouting guide for the full process.
- Rake out old grout with a hand grout saw or oscillating tool, taking care not to chip the tile edges or scratch the glaze.
- Vacuum the joints and let the wall dry completely, because trapped moisture ruins both cement and epoxy grout.
- Replace any cracked or hollow tiles first, since new grout will not hold a loose tile in place.
- Regrout the walls before the floor, and silicone the internal corners and base afterwards rather than filling them with grout.
- Stop and check the wall linings if the house is pre-1990, and never grind or cut suspected asbestos sheeting.
- Book a licensed waterproofer if you find a cracked membrane, soft plasterboard or water coming through the ceiling below.
Shower screen seal, shower rubber seal and complete shower seal
Grout does not seal the moving or corner joints. Silicone and rubber seals do that job, and they fail first in most showers.
| Seal | Where it goes | What to watch |
|---|---|---|
| Silicone bead | Internal corners, base of walls and where tile meets the screen frame | Use a mould-resistant sanitary silicone and read how to silicone a shower before you start. |
| Shower rubber seal or bubble seal | Bottom edge and door edge of a framed or frameless screen | Measure the glass gap and thickness, since seals come in several profiles. |
| Magnetic or vertical seal | Edge of pivot and hinged screens | Worn strips let water out, so replace them as a pair where needed. |
| Complete shower seal kit | Replacing every seal on a screen in one go | Check the kit matches your brand and glass; mixed parts leak. |
| Old silicone removal | Before reapplying any bead | Follow how to remove silicone, then cure with how long silicone takes to dry in mind. |
- DIY shower screens: refitting a seal strip is a simple DIY, but installing a new screen is a two-person job because the glass is heavy.
- Waterproofing and plumbing behind the wall belong to a licensed plumber or waterproofer, never to a handyman or the homeowner.
How to remove mould from shower silicone
Black mould on shower silicone usually means the bead is old, thin or constantly damp. Our mould on shower silicone guide explains causes and long-term fixes.
- Wipe the surface with a cleaner made for bathroom mould, following the product label and testing on a hidden spot first.
- Never mix cleaning chemicals, and ventilate the room because bleach and acidic cleaners release harmful fumes.
- Replace the silicone if black marks sit deep inside the bead, since surface cleaning only hides the stain for a while.
- Run the exhaust fan after every shower and squeegee the screen, so the bead dries instead of staying damp.
- Use a mould-resistant sanitary silicone, and apply a thin, even bead rather than a thick one.
- Check for a leak if mould returns quickly, as a failed seal or membrane keeps the corner permanently wet.
Sealing grout and tiles, and how to use grout sealer
Cement grout needs sealing, while cured epoxy grout does not. Our grout sealing guide covers products and timing.
- Clean and dry cement grout fully, then apply the sealer with a small brush or applicator, wiping excess off the tile surface.
- Wait for the stated cure time before sealing new cement grout, because sealing too early traps moisture and causes patchy colour.
- Choose a penetrating sealer for natural stone and unglazed tile, and test an offcut first to check the finish.
- Skip sealer on epoxy grout, since the resin already blocks water and an extra coat can leave a sticky film.
- Reseal cement grout in wet areas on a regular schedule, and watch for darkening joints as your cue (indicative — check the label).
- Keep sealer off the glaze of polished tiles, as it can leave marks that are hard to buff out.
Cleaning epoxy grout and keeping it looking new
Epoxy grout is easy to maintain, and our how to clean grout guide shows the gentlest methods for each type.
- Wipe the shower down after use with a squeegee or cloth to stop soap scum building up.
- Use a neutral pH cleaner and a soft brush, avoiding harsh acids that can dull the surface or fade pigments.
- Keep abrasive scourers away, because scratches collect dirt and are impossible to buff back to a smooth surface.
- Check silicone lines every few months and replace any that crack or peel.
FAQ: epoxy grout
What is epoxy grout?
Epoxy grout is a two-part resin grout made from epoxy resin and a hardener. It cures to a hard, waterproof finish that resists stains and mould, so it suits showers and splashbacks. It costs more than cement grout and sets quickly, so you need to follow the packet instructions carefully.
How to grout tile?
Clean the joints, mix the grout as the packet says, and press it in with a rubber float held at an angle. Wipe the surface with a damp sponge, then clean off the haze before it hardens. Keep the area dry for the stated cure time before using it.
How to regrout tiles?
Rake out the old grout without chipping the tile edges, vacuum the joints, and let the wall dry. Mix the new grout, press it in, and clean the haze. Silicone the corners and base afterwards. Check for asbestos first in homes built before 1990.
Is it hard to regrout a shower?
It is more fiddly than hard. Removing the old grout takes the most time, and epoxy grout rewards careful, small-section work. If you find a leak, loose tiles or soft plasterboard, stop and book a licensed waterproofer rather than grouting over the problem.
How to use grout sealer?
Apply sealer to clean, dry cement grout after it has fully cured, using a small brush or applicator. Wipe off any excess from the tile face. Epoxy grout does not need sealer. Always follow the product label for cure and recoat times.
Can you regrout tiles over old grout?
Not properly. New grout needs a clean, deep joint to bond, so remove the old grout first. Applying grout over a worn surface leaves a weak bond that cracks or lifts. Rake out most of the depth, clean the dust, and then regrout.
Getting epoxy grout installed in Sydney
If you would rather not wrestle with fast-setting resin, we can regrout, reseal and tidy up your wet areas in one visit. Book a Sydney handyman for regrouting and silicone, and use a licensed plumber or waterproofer for leaks, membranes or anything behind the tiles.
Related guides
- Learn more in our shower regrouting guide for step-by-step instructions.
- Compare options in grout types and colours before you buy.
- Read how to silicone a shower for a clean, waterproof bead.
- See how to remove silicone before reapplying any seal.
- Keep joints fresh with how to clean grout.
- Follow how to grout tiles for general technique.
- Protect cement joints with grout sealing.
- Check how long silicone takes to dry before using the shower.
- Plan around how long grout takes to dry before you walk on it.
- Fix recurring stains with mould on shower silicone advice.


