What Size Drill Bit for Green Wall Plugs?

What size drill bit for green wall plugs depends on the plug in your hand, because plug colours are not standardised and the correct bit size is printed on the packet. Match the bit to the plug body, drill a test hole, and the plug should push in snugly and then grip as the screw goes in.

This guide covers choosing and fitting wall plugs, drywall plugs, wall anchor bolts, anchor studs and metal anchors, plus when to call a handyman. If you are fixing something heavy, read our stud finder guide first.

Key points

  • Difficulty: about 8 steps, and the one tool you cannot skip is a drill with the correct masonry or general-purpose bit for the wall.
  • Always take the bit size and screw size from the plug packet, because colours differ between brands.
  • Safety check: scan for cables and pipes before drilling, and test pre-1990 wall linings for asbestos first.
  • A Sydney handyman typically charges $125 for picture or shelf hanging (range $80–$205) and $140 as a minimum call-out (range $92–$170).

Can you fit green wall plugs yourself?

Most light fixings are a sensible DIY job, but the wall type and the load decide whether a plug is the right choice.

SituationDIY OK?Why
Brick or block wall, light itemYesA masonry bit and a matching plug give a solid fixing when sized to the packet.
Plasterboard, light itemYes, with a plasterboard anchorA standard plug in hollow board can pull out, so use a fixing made for hollow walls.
Heavy shelf, TV or cabinetFind framing or ask a proFix into studs or masonry; our TV wall mount guide shows the right approach.
Tiled wallUse the tile guide firstDrilling cracked tile is a common error; see how to drill into tiles.
Pre-1990 fibro or old sheetingTest firstTreat suspect material as asbestos and see asbestos.nsw.gov.au before drilling.
Rental propertyCheck consentPicture hooks, nails and screws for frames are minor changes, but ask in writing first.

Tools and materials for wall plugs

A small kit covers most jobs, and a good bit set is worth more than a cheap pack of plugs.

ItemWhat it is forTip
Drill with hammer actionDrills masonry and blockTurn hammer action off for plasterboard and tile.
Masonry and general-purpose bitsMatch the plug diameterTest the bit against the plug body before you drill.
Stud and cable detectorFinds framing and hidden servicesScan before every hole, not once per wall.
Wall plugs and matching screwsHold the screw in the wallUse the screw size on the packet and check the wall type it suits.
Spirit level and pencilSets position and levelMark the hole centre with a small cross.
Vacuum or dust sheetCleans the holeDust left in a hole weakens the grip.

What size drill bit for green wall plugs: step by step

Follow the packet first, then use this routine to avoid oversized holes and stripped plugs.

  1. Read the packet for the recommended drill bit diameter, screw size and wall type, and keep it until the job is done.
  2. Hold the bit against the plug body; the bit should match the plug’s outer diameter closely, not be noticeably larger.
  3. Scan the wall for studs, cables and pipes, and stay away from vertical and horizontal lines running from switches and power points.
  4. Mark the hole position, then drill a test hole in a hidden spot or scrap piece to check the plug pushes in firmly.
  5. Drill the hole to the depth of the plug plus a little extra for dust, using tape on the bit as a depth marker.
  6. Clear the dust with a vacuum or brush, then tap the plug in until it sits flush with the wall surface.
  7. Fix the item with the screw size the packet states, driving it slowly until the plug grips, without over-tightening.
  8. Check the fixing is firm and level before you load it, and never rely on a plug for something heavy or critical.

Drywall wall plugs for plasterboard

Hollow plasterboard needs a fixing that spreads load behind the board, and Sydney units often have thin lining over hollow cavities.

  • Choose a drywall plug, toggle or cavity anchor made for hollow walls, and check the packet for the wall thickness it suits.
  • Avoid standard masonry plugs in plasterboard, since they can spin or pull straight through the board.
  • Use a stud finder and fix into the timber or steel stud for anything heavy or likely to be pulled on.
  • Pre-drill a pilot hole of the size stated on the packet and do not hammer the anchor flush.
  • Stop tightening as soon as the anchor grips, because over-tightening crushes the board and weakens the hold.

Wall anchor bolts and anchor studs for brick and concrete

Heavy fixings in masonry call for a bolt or stud anchor, and double brick in older Inner West terraces blunts cheap bits quickly.

  • Use a wall anchor bolt or anchor stud designed for masonry, and follow the packet for hole size, depth and tightening.
  • Drill with hammer action and a sharp masonry bit, and withdraw the bit often to clear dust.
  • Keep fixings well back from brick edges and mortar joints, since solid brick holds better than a crumbly joint.
  • Blow out the hole before inserting the anchor, because dust is the most common cause of a loose fix.
  • Read our guide to drilling into brick for bit and technique details.

Metal wall anchor options for hollow and stud walls

A metal wall anchor suits shelves, mirrors and curtain fittings where the wall behind is hollow or the item is awkward.

  • Choose a metal toggle, spring toggle or self-drilling anchor for plasterboard when a plastic plug is not suitable.
  • Look at the packet for the material, wall thickness and load guidance, and never exceed it.
  • Prefer fixing into a stud, and see our stud wall guide if you are working with open framing.
  • Do not guess the load rating; the packet is the only source you can rely on.
  • Replace any bent, stripped or corroded anchor rather than reusing it.

What size drill bit for green wall plugs in a rental

The bit size is the same, but renters have extra rules about drilling and patching.

  • Ask your landlord in writing before you drill, even though NSW lets you request picture hooks, nails and screws for hanging frames.
  • You can also ask to anchor furniture to a non-tiled wall, and a landlord cannot unreasonably refuse.
  • Photograph the wall before you start so you can show its condition when you move out.
  • Use the smallest suitable fixings and fill unused holes neatly with a filler that matches the wall.
  • Strata, heritage and loose-fill asbestos register homes have extra limits, so check your lease and by-laws.

Common mistakes when fitting wall plugs

  • Choosing the plug by colour rather than reading the packet, then drilling a hole that is too large or too small.
  • Skipping the cable and pipe scan and drilling into a live wire or water pipe.
  • Using a masonry plug in plasterboard, or a plasterboard anchor in brick.
  • Over-tightening the screw so the plug spins in its hole and loses its grip.
  • Ignoring asbestos risks in a home built before 1990 when drilling sheeting or eaves.
  • Hanging a heavy mirror or TV from plugs when it needs studs or masonry fixings and a second person.

When to call a handyman for wall plugs and anchors

  • Call a handyman for anything heavy, tall or valuable, such as shelves, mirrors, TVs and tall furniture that must be anchored.
  • Tall furniture and TVs should be fixed to the wall because tip-overs injure children; at least 14 children under nine died in Australia from 2000 to 2015 after furniture fell on them.
  • Use a licensed electrician if a wall scan finds cabling in your path, or if you want to move power points or lights.
  • Use a licensed plumber if you hit a pipe or need to move taps.
  • Use a pro to deal with tile, stone or old fibro, where wrong drilling causes cracks.
  • Hand any renovation valued at more than $5,000 to a builder licensed by Building Commission NSW.

Cost to hire a handyman for wall plug and anchor jobs in Sydney

JobLowTypicalHigh
Picture or shelf hanging$80$125$205
Handyman hourly rate, Sydney$57$105$140
Call-out or minimum charge, Sydney$92$140$170
Half-day handyman, Sydney (4 hours)$230$415$645
Full-day handyman, Sydney (8 hours)$435$690$1025

FAQ: drill bit sizes and wall anchors

What size drill bit for green wall plugs?

Use the size printed on the packet, because green plugs are not the same in every brand. Hold the bit against the plug body to confirm they match, and drill a test hole before the real one.

What are drywall wall plugs?

They are fixings designed for hollow plasterboard, such as plastic expansion plugs, toggles and self-drilling anchors. They spread the load behind the board. Check the packet for wall thickness and fix into studs for heavy items.

When should I use a wall anchor bolt or anchor stud?

Use them in solid masonry or concrete for heavier fixings, such as brackets and frames, following the packet for hole size and depth. Never rely on them in hollow plasterboard, and check for cables first.

Are metal wall anchors stronger than plastic plugs?

For hollow walls, metal toggles often grip better, but strength depends on the product and the wall. Read the packet for load guidance, and fix into a stud wherever you can.

Getting wall plugs and anchors fitted in Sydney

If you would rather not guess at fixings, we can scan the wall, choose the right plug or anchor for the material and fix your shelves, mirrors and brackets securely. Book a Sydney handyman, and read the epoxy grout guide and kitchen renovation cost guide for bigger projects.