How to drill into brick: mark the spot, fit a masonry bit to a hammer drill, drill square to the wall at steady pressure, clear the dust, then fit a wall plug or anchor sized for your bracket. The most common failure is drilling into the mortar joint or a hollow brick and trusting a fixing that cannot hold.
This guide covers how to drill into brick step by step, what a hammer drill is, how to drill into concrete, and what a Sydney handyman charges if you would rather not do it yourself.
Key points
- This is a ten-step job that takes a beginner a few minutes per hole once the drill, bit and plug are matched, and the first hole is always the slowest.
- A hammer drill with a sharp masonry bit is the one tool you cannot skip, because a standard drill in rotary mode glazes the bit and wanders off line.
- Scan for cables and pipes before you drill, wear eye and dust protection, and treat any pre-1990 render or sheeting as possible asbestos until it is checked.
- A Sydney handyman typically charges about $125 for a picture or shelf hanging visit (range $80–$205, October 2026), and about $140 as a call-out for a short job.
Can you drill into brick yourself?
Most people can drill a handful of holes in brick safely. Use this table to check your wall and your situation first.
| Your situation | DIY OK? | Why |
|---|---|---|
| Solid clay brick, single or double | Yes, with a hammer drill | It drills cleanly and holds a plug well, but older Inner West double brick eats cheap bits quickly. |
| Hollow or cored brick | Check first | A hole in a cored brick loses grip, so you need a fixing made for hollow masonry and the packet rating. |
| Concrete block, render or concrete slab | Yes, with the right bit | It is harder than brick, so use a sharp masonry or SDS bit and let the hammer action do the work. |
| Heavy load such as a TV, cabinet or hanging chair | Experienced DIYers | Heavy loads need a fixing sized by the manufacturer’s instructions, never a guess, and a second person to hold the item. |
| Pre-1990 home with rendered, fibro or sheeted walls | Check first | Homes built or renovated before 1990 are likely to contain asbestos, so identify suspect material at asbestos.nsw.gov.au before you drill. |
| Rental property | Ask first | Get written consent before you drill; a NSW landlord cannot unreasonably refuse minor changes such as picture hooks, but you must ask first. |
| Near power points, switches or a meter box | No | Moving or adding electrical work needs a licensed electrician, and drilling into hidden cable is dangerous. |
What is a hammer drill?
A hammer drill spins the bit and also delivers rapid forward blows, which is why it cuts brick and concrete that would stall a normal drill.
| Term | What it means | Why it matters |
|---|---|---|
| Hammer drill | A drill with a hammer mode that adds short forward blows while the bit rotates. | It is the standard DIY choice for brick, block and concrete, and many cordless drills from Ryobi or Makita include it. |
| Rotary hammer (SDS) | A heavier tool with a piston mechanism and a slotted chuck that takes SDS bits. | It drills faster with less effort and suits big jobs, but it is more tool than most households need. |
| Masonry bit | A bit with a hardened tip designed to crush brick and concrete. | A general-purpose bit will blunt and burn in brick, so buy a masonry bit marked for your drill type. |
| Hammer mode | A switch or collar setting that turns the percussion action on. | Use it for brick and concrete, and switch it off for tiles and timber, or you will crack the tile or tear out the grain. |
Tools and materials to drill into brick
| Item | What it’s for | Tip |
|---|---|---|
| Hammer drill | Drills the hole with rotation and percussion | Use a cordless one if you have a few holes, or a corded one for a long job on a hot day. |
| Masonry bits | Cut the hole to match the plug | Match the bit size to the plug or anchor on the packet, and replace any bit with a rounded or cracked tip. |
| Cable and pipe detector | Finds live wires and pipes before you drill | Scan twice, in a cross pattern, and avoid the vertical and horizontal lines from power points and switches. |
| Wall plugs or anchors | Grip inside the hole | Check the packet rating for your wall type and load; our wall plugs and anchors guide compares the main options. |
| Masking tape and pencil | Marks the spot and a depth guide | Wrap tape around the bit at the needed depth so you know when to stop. |
| Vacuum or dust pump | Clears dust from the hole | Dust in the hole weakens the grip of the plug, so clean it out before you fit anything. |
| Safety glasses and dust mask | Protects your eyes and lungs | Wear both every time, and add hearing protection if you are drilling more than a couple of holes. |
How to drill into brick: step by step
Work with a second person for any heavy item or any height above your shoulder.
- Scan the wall with a detector for cables and pipes, then mark the hole position in pencil, keeping clear of the lines from power points and switches.
- Aim for the centre of a brick rather than a mortar joint, because mortar crumbles and gives a weak hold for most fixings.
- Choose a masonry bit that matches the plug on the packet, and tape the bit at the depth of the plug plus a little extra for dust.
- Fit the bit to a hammer drill, switch on hammer mode, and set the speed low to start so the tip bites rather than skates across the brick.
- Hold the drill square to the wall with both hands, press firmly but steadily, and let the bit and hammer do the cutting.
- Pull the bit out every few seconds to clear dust, and stop if it suddenly drops through, which means a hollow core or a cavity.
- Drill to the tape marker, then vacuum or blow out the hole until no dust is left, wearing eye and dust protection.
- Tap the plug in flush with the wall surface, using a hammer if it is tight, and check it does not spin in the hole.
- Drive the screw or bolt in with a screwdriver or socket, stopping when it is snug rather than forcing it past the point it grips.
- Test the fixing by hand before you hang anything, then add the load slowly and recheck the plug after the first day of use.
How to drill into concrete
Concrete follows the same steps as brick, but it is harder and often hides steel reinforcing, so expect slower progress and a sharper bit.
- Use a fresh masonry or SDS bit, because a worn tip will polish the hole and make it slower and hotter in concrete.
- Keep the drill square and let the hammer action work, as leaning harder only overheats the bit and wears out the chuck.
- If you hit steel reinforcing, stop, move the hole slightly and start again, because a masonry bit will not cut through steel.
- Use a hole depth and anchor type from the anchor maker’s instructions, such as the sleeve or screw bolts sold by Ramset, and do not guess.
- Blow or vacuum out each hole completely before fitting an anchor, since concrete dust is the main cause of poor grip.
- Never drill into a post-tensioned slab or structural beam without advice from a builder or engineer, because cutting a tendon is serious.
Common mistakes when you drill into brick
- Using the wrong plug for the wall, such as a plasterboard plug in brick, instead of one matched to the material and the packet rating.
- Skipping the cable and pipe scan, then drilling straight above or beside a power point where wiring commonly runs.
- Drilling without hammer mode or with a blunt bit, which overheats the tip and takes much longer than it should.
- Over-tightening the screw so the plug spins in the hole or the brick face cracks around the fixing.
- Ignoring asbestos in render, fibro or sheeting in a pre-1990 home before you drill, cut or sand it.
- Working alone with a heavy or overhead item, when a second person would hold the load and steady the ladder.
When to call a handyman (or a licensed trade)
- The item is heavy or awkward, such as a TV, a large mirror or a wall cabinet, and you want it fixed to the right standard.
- The wall is hollow brick, crumbly old brick or rendered, and you are unsure which anchor type will suit.
- You need to drill near power points or run a new cable, which needs a licensed electrician such as TQN Electrician.
- You suspect pipes in the wall, so book a licensed plumber rather than drill and risk a leak.
- Your home was built or renovated before 1990 and the surface might be asbestos-containing sheeting or render.
- You are renting, and you want the job done neatly with a record of the holes for your landlord.
Cost to hire a handyman to drill into brick in Sydney
Prices include GST and come from October 2026 Sydney data. Our TV wall mounting guide shows how brick drilling fits into larger jobs.
| Job | Low | Typical | High |
|---|---|---|---|
| Picture or shelf hanging, Sydney (per visit) | $80 | $125 | $205 |
| TV wall mounting, Sydney (per job) | $115 | $205 | $290 |
| Handyman hourly rate, Sydney | $57 | $105 | $140 |
| Call-out or minimum charge, Sydney | $92 | $140 | $170 |
| Half-day handyman, Sydney (4 hours) | $230 | $415 | $645 |
- Brick and concrete drilling often costs more than plasterboard because it takes more time and wears bits.
- Bundle several fixings into one visit so the call-out charge covers more work.
- Ask whether the quote includes plugs, anchors and a stud or cable scan.
FAQ: how to drill into brick
How to drill into brick?
Use a hammer drill with a sharp masonry bit sized to your plug. Mark the spot, aim for the brick centre rather than the mortar, and drill square at steady pressure. Clear the dust, fit the plug flush, then drive the screw until snug. Always scan for cables and pipes first.
What is a hammer drill?
A hammer drill is a power drill that spins the bit and adds rapid forward blows, so it cuts brick, block and concrete that a standard drill cannot. Most cordless models have a hammer switch you turn off for tiles and timber. SDS rotary hammers are heavier tools for bigger jobs.
How to drill into concrete?
Use a hammer drill or SDS drill with a sharp masonry bit, hold it square, and let the hammer action do the work. Pull the bit out to clear dust, stop if you hit steel reinforcing, and clean the hole before fitting an anchor made for concrete.
Can I drill into brick without a hammer drill?
You can drill a few shallow holes in soft brick with a standard drill and a sharp masonry bit, but it is slow and wears the bit. For anything heavy or for hard brick and concrete, a hammer drill is safer and gives a cleaner, more reliable hole.
Getting your brick drilled in Sydney
If you would rather not buy a hammer drill, we can scan the wall, drill and fit the right anchors in one visit. Our handymen bring masonry bits, dust control and a detector for every job. Book a Sydney handyman and add other small jobs to the same visit. Before you start, our stud finder guide explains how to scan a wall.


