How to tile a bathroom: confirm the waterproofing is done and cured, set out the layout from the centre, spread adhesive with the right notched trowel, lay tiles with spacers, then grout and flex-seal the corners. The biggest thing that goes wrong is tiling over missing or damaged waterproofing, which leaks into the wall and slab long before you see a stain.
This guide covers how to tile a bathroom floor and walls step by step, when the job stops being DIY, and what a Sydney handyman charges for the tiling-adjacent work.
Key points
- The job runs in about nine steps, and the first step is always checking that waterproofing is in place before a single tile goes down.
- A level and a notched trowel matched to your tile packet are the two tools you cannot skip.
- Waterproofing and any plumbing changes need a licensed trade, and pre-1990 homes may hide asbestos in wet-area linings.
- A Sydney handyman charges a call-out or minimum of $92 to $170 (typical $140, October 2026) and $57 to $140 per hour, so small repairs cost far less than a retile.
Can you tile a bathroom yourself?
Experienced DIYers can tile a flat, dry, already-waterproofed bathroom. Use this table to check your own bathroom before you buy tiles.
| Your situation | DIY OK? | Why |
|---|---|---|
| Sound, flat walls with waterproofing already done and cured | Yes | Tiling onto a prepared, waterproofed surface is a skill you can learn on a small wall first. |
| No waterproofing, or a membrane you cannot confirm | No | Waterproofing needs a licensed trade, so book a licensed waterproofer before you tile. |
| Moving the shower, vanity or toilet | No | Moving taps, pipes or drains is plumbing work that needs a licensed plumber in NSW. |
| Pre-1990 home with old sheeting, wet-area linings or floor coverings | Check first | Homes built or renovated before 1990 are likely to contain asbestos, so identify suspect material before you disturb it. |
| Uneven floor or cracked slab | Check first | Tiles crack over movement, so repair or level the base before laying anything on top. |
| Whole-bathroom renovation valued at more than $5,000 | No | Residential building work over $5,000 must be done by someone licensed by Building Commission NSW. |
| You are renting | Ask first | Retiling is a major change, so get written consent from the landlord or agent before you plan anything. |
Tools and materials to tile a bathroom
| Item | What it is for | Tip |
|---|---|---|
| Tiles and spare box | The finished surface | Buy extra from the same batch, because colours shift between production runs and you will need offcuts for edges. |
| Tile adhesive | Bonds the tile to the wall or floor | Choose one rated for wet areas and your tile type, such as products from Ardex or Mapei, and follow the packet. |
| Notched trowel | Spreads an even adhesive bed | Match the notch size to the tile packet and the tile size, since large tiles need deeper ridges. |
| Spirit level and laser line | Keeps rows straight | Check the first row twice, because every later row copies its mistakes. |
| Tile cutter, wet saw and grinder | Cuts around pipes, corners and edges | Wear a dust mask rated for silica, goggles and ear protection, as cutting tile makes fine silica dust. |
| Spacers, grout and flexible silicone | Joint size, joint fill and movement joints | Use silicone, not grout, in corners and at the base of the wall, as these joints must move. |
How to tile a bathroom: step by step
- Plan the layout on paper and mark the centre line of each wall and the floor so cut tiles land in the least visible corners.
- Check the old lining and floor before you disturb them, and stop if you suspect asbestos in a pre-1990 home.
- Confirm a licensed waterproofer has finished the membrane and that it has fully cured according to the manufacturer’s instructions before you tile.
- Clean the surface, remove dust and grease, and fix any bumps or hollows so the base is flat enough to take your tile size.
- Dry-lay a row of tiles with spacers along the floor or the first wall course to confirm the layout before adding any adhesive.
- Mix adhesive exactly to the packet, spread a small area with the notched trowel, and comb the ridges in one direction.
- Press each tile with a slight twist, add spacers, and check with a level every few tiles so rows stay straight.
- Cut tiles with a wet saw or cutter, wearing a silica-rated dust mask and goggles, and keep offcuts dry until the adhesive has set.
- Grout only after the adhesive has cured per the packet, then clean haze, and seal corners and junctions with flexible silicone.
How to tile a bathroom wall
Bathroom walls look easy because gravity helps, but one slipping row ruins the whole pattern, and shower walls take the most water.
- Start from a level support batten rather than the floor, because old Sydney bathrooms rarely have a floor that is truly flat.
- Work from the centre outwards so cut tiles at each corner are balanced and never a thin sliver beside the shower screen.
- Tile around taps and outlets by marking the tile, using the cutter, and leaving a small gap for the escutcheon to cover.
- Keep adhesive off the grout lines by cleaning ridges and squeeze-out while the adhesive is still wet.
- Use a second person to hold large format tiles, since heavy wall tiles can slip or snap during positioning.
How to tile a bathroom floor
Floors carry foot traffic and water, so falls to the drain and a flat bed matter more than the look.
- Check the floor falls toward the waste before you lay anything, as tiles that pool water cause mould and slipping hazards.
- Tile away from the door, working toward the exit, so you never trap yourself in the corner with wet adhesive.
- Back-butter larger floor tiles with adhesive, because hollow spots under a tile crack when someone stands on them.
- Pick a slip-rated tile for wet areas, and check the supplier’s rating rather than relying on appearance.
- Keep traffic off for the time the adhesive and grout packets state, and refit the toilet using the guide to tightening a toilet seat afterwards.
Common mistakes when you tile a bathroom
- Tiling over unconfirmed waterproofing or a membrane that has not cured, which traps water behind the tiles.
- Skipping the dry layout, then discovering tiny slivers at one wall and a full tile at the other.
- Using the wrong trowel notch or old adhesive, which leaves hollow patches that crack under foot traffic.
- Grouting corners and wall-to-floor joints instead of using flexible silicone, so cracks open up within months.
- Cutting or sanding old fibro, wet-area sheeting or old floor coverings in a pre-1990 home without checking asbestos.nsw.gov.au first.
- Tiling over a cracked or moving slab, when the real fault needs a repair like those in our concrete crack repair guide.
When to call a handyman (or a licensed trade)
- You need waterproofing done or checked, which is a job for a licensed waterproofer rather than a DIY product.
- The shower, vanity or toilet must move, so book a licensed plumber for taps, pipes and drains.
- Existing tiles are cracked or drummy in a small area, which a handyman can fix with the steps in our cracked tile repair guide.
- The bathroom was built or renovated before 1990 and the sheeting or floor covering might contain asbestos.
- The job is part of a renovation valued at more than $5,000, which must be done by someone licensed by Building Commission NSW.
- You want a neat result with large format tiles, tricky cuts or a feature wall, and would rather book a tiler than learn on the job.
Cost to hire a handyman for bathroom tiling in Sydney
These prices include GST and come from October 2026 Sydney handyman data. A full retile with waterproofing is a renovation job priced by scope (indicative — get itemised quotes).
| Charge | Low | Typical | High |
|---|---|---|---|
| Call-out or minimum charge, Sydney | $92 | $140 | $170 |
| Handyman hourly rate, Sydney | $57 | $105 | $140 |
| Half-day handyman, Sydney (4 hours) | $230 | $415 | $645 |
| Full-day handyman, Sydney (8 hours) | $435 | $690 | $1025 |
- A full day can cost less than eight hourly-billed hours, so batch small repairs together.
- Any NSW home building contract must be in writing, with a maximum deposit of 10% before work starts.
- Work over $20,000 needs a full home building contract plus Home Building Compensation cover.
FAQ: how to tile a bathroom
How to tile a bathroom for the first time?
Start with a small wall. Confirm waterproofing, set out the layout from the centre, spread adhesive with the packet-rated trowel, and keep every row level. Grout after the adhesive cures, then seal the corners with flexible silicone rather than grout.
Do you need to waterproof before you tile a bathroom?
Yes. Wet areas need a cured waterproof membrane before tiles go on. Book a licensed waterproofer to do or check it, and never tile over a membrane that you cannot confirm has been installed and cured.
Can you tile over existing bathroom tiles?
Sometimes, if the old tiles are sound, flat and well bonded, but it raises the surface and can hide movement. Our how to tile guide covers the preparation, and a handyman can check drummy tiles first.
Is old bathroom tiling a risk in a pre-1990 home?
It can be, because homes built or renovated before 1990 are likely to contain asbestos in wet-area linings and floor coverings. Check asbestos.nsw.gov.au, treat suspect material as asbestos, and do not cut, drill or sand it yourself.
Getting your bathroom tiled in Sydney
If you would rather leave the cutting and grouting to someone else, we can repair, regrout and reseal tiles in your bathroom and book licensed trades for waterproofing and plumbing. Book a handyman in Sydney for small tile jobs, or start with our guide to replacing a toilet seat while the room is in use.
Related guides
- How to replace a toilet seat in your bathroom
- How to remove wallpaper before you tile or paint
- Concrete crack repair for slabs and floors
- Cracked tile repair for small bathroom jobs
- How to tile a wall or floor step by step
- How to replace skirting boards
- How to tighten a toilet seat that keeps moving


