How to tile a splashback: prepare a clean, flat wall, set out a level first row on a support batten, comb adhesive onto the wall, press tiles in with spacers, then grout and seal the joins with silicone. The biggest thing that goes wrong is a crooked first row, because every row after it follows the same mistake.
This guide covers how to tile a kitchen splashback step by step, how to handle cooktops and power points safely, when to book a trade, and what a Sydney handyman charges.
Key points
- A splashback is a manageable weekend job of about nine steps, and the first row decides how good the finished wall looks.
- A long spirit level and a support batten are the two tools you cannot skip, because benchtops and walls are rarely truly level.
- Power points and gas cooktops are licensed-trade territory, so never loosen, move or modify them yourself.
- A Sydney handyman charges a call-out or minimum of $92 to $170 (typical $140, October 2026) and $57 to $140 per hour, with sealing work priced separately.
Can you tile a splashback yourself?
Most renovators can tile a straight, dry kitchen splashback with patience and a level. Check your situation in this table first.
| Your situation | DIY OK? | Why |
|---|---|---|
| Flat painted plasterboard behind a benchtop | Yes | Painted plasterboard takes tile adhesive well once it is clean and keyed, following the adhesive packet. |
| Power points or switches in the tiling area | Check first | Switch the circuit off, but do not loosen or move the fitting yourself, and ask a licensed electrician to adjust it. |
| Gas cooktop with a splashback behind it | Check first | Gas work needs a licensed gasfitter, and clearances behind the cooktop come from the manufacturer’s instructions. |
| Old wallpaper, damaged lining or uneven wall | Check first | Tiles will not bond to loose paper or crumbling plaster, so repair and level the wall before you start. |
| Pre-1990 home with fibro or old sheeting | No, check asbestos first | Homes built or renovated before 1990 are likely to contain asbestos, so identify suspect material before you disturb it. |
| Large format tiles or full-height splashback | Experienced DIYers only | Heavy tiles need a second person to lift and hold them, and ladders are risky for solo work above shoulder height. |
| You are renting | Ask first | Tiling is a permanent change, so get written consent from the landlord or agent before you buy anything. |
Tools and materials to tile a splashback
| Item | What it is for | Tip |
|---|---|---|
| Tiles and spares | The finished surface | Order extra from the same batch, because cuts around power points and corners use more tiles than you expect. |
| Tile adhesive | Bonds the tile to the wall | Choose one rated for your tile and wall type, such as products from Ardex or Mapei, and follow the packet instructions. |
| Notched trowel | Spreads an even adhesive bed | Pick the notch size recommended on the adhesive or tile packet, and comb all ridges in one direction. |
| Spirit level and straight batten | Sets a level first row | Screw a temporary batten to the wall above the benchtop and start the second row from it. |
| Tile cutter or wet saw and nippers | Makes straight and notched cuts | Wear goggles and a dust mask rated for silica, because cutting tile makes fine dust. |
| Grout, sponge and neutral silicone | Fills joints and seals the benchtop edge | Use silicone, not grout, where the tile meets the benchtop, as that joint needs to flex. |
How to tile a splashback: step by step
- Clear the benchtop, tape off the edge, and measure the splashback area carefully, adding extra tiles for cuts and breakage.
- Check for old wallpaper, loose paint or damaged plaster, and fix them first, using our wallpaper removal guide if needed.
- Turn off power to nearby outlets, then clean the wall with a degreaser and let it dry fully before you open any adhesive.
- Dry-lay a row of tiles on the benchtop to plan cuts, aiming for no thin slivers beside windows or at the corners.
- Screw a temporary batten along the wall so the tops of the first row sit level, even if the benchtop slopes.
- Spread adhesive with the notched trowel over a small area, and comb ridges in one direction, working only as much as you can tile before it skins.
- Press each tile in with a slight twist, add spacers, and check level and flush faces with the spirit level every few tiles.
- Cut tiles to fit around outlets, windowsills and cooktops, leaving the small gaps the fitting covers will hide.
- Grout only after the adhesive has cured according to the packet, clean the haze, then seal the benchtop and corner joins with flexible silicone.
How to tile a splashback behind a cooktop
The wall behind the cooktop gets heat, grease and splashes, so choose materials and clearances with care.
- Check the cooktop’s manufacturer instructions for the minimum clearance to combustible surfaces and tile height behind the burners.
- Use adhesive and grout suitable for kitchen areas, and check the packet for heat exposure near the cooktop.
- Keep tiles clear of the cooktop edge with a small gap, then fill it with a heat-rated silicone made for this use.
- Book a licensed gasfitter or electrician to disconnect, lift or reconnect the cooktop, because that is licensed work in NSW.
- Seal natural stone and unglazed tile behind the cooktop, as oil stains soak straight into porous surfaces.
How to tile a splashback around power points and edges
Cuts around fittings and edges are where a good tile job looks neat or sloppy.
- Mark the outlet position on the tile using a cardboard template, then cut slowly with a wet saw or tile nippers.
- Leave the faceplate on and tile up to it with a small gap, unless a licensed electrician has pulled the fitting forward.
- Ask a licensed electrician to extend or relocate any power point that ends up recessed behind the new tile.
- Finish exposed tile edges with a trim or a neat cut, so the edge does not catch on cloths or sponges.
- Run a continuous bead of silicone at the benchtop and window corners, and smooth it with a damp finger or tool.
Common mistakes when you tile a splashback
- Starting from the benchtop instead of a level batten, which leaves rows sloping with the benchtop.
- Tiling over greasy, dusty or flaking paint, so the tiles drop away after a few months of cooking.
- Removing or loosening power point fittings yourself, instead of asking a licensed electrician to do it safely.
- Grouting the corner against the benchtop, which cracks as the bench moves, instead of using flexible silicone.
- Ignoring the asbestos risk in a pre-1990 home, especially when cutting or drilling old sheeting behind the stove.
- Lifting heavy tiles above shoulder height alone, instead of getting a second person to hold the tile or steady the ladder.
When to call a handyman (or a licensed trade)
- A power point is in the way and needs moving or extending, so book a licensed electrician.
- The cooktop is gas or must be lifted for tiling, so book a licensed gasfitter.
- Your wall is uneven, damaged or has old wallpaper, and you want it prepared before tiling starts.
- The home was built or renovated before 1990 and the wall sheeting might contain asbestos.
- Tiles are cracked or loose in a small area, and a quick fix is better than starting again with our cracked tile repair guide.
- The kitchen is part of a renovation valued at more than $5,000, which must be done by someone licensed by Building Commission NSW.
Cost to hire a handyman for a splashback in Sydney
These prices include GST and come from October 2026 Sydney handyman data. A full splashback tiling job depends on size and tile type (indicative — get itemised quotes).
| Charge | Low | Typical | High |
|---|---|---|---|
| Call-out or minimum charge, Sydney | $92 | $140 | $170 |
| Handyman hourly rate, Sydney | $57 | $105 | $140 |
| Half-day handyman, Sydney (4 hours) | $230 | $415 | $645 |
| Weatherproofing or caulking, Sydney (per job) | $115 | $205 | $345 |
| Minor plastering or patching, Sydney (per job) | $140 | $230 | $575 |
- Plastering ranges are wide because the scope varies, so ask for a written quote before work starts.
- The cost of tiles and adhesive is usually extra unless the quote says otherwise.
- Batch small jobs into one booking, because the call-out fee applies even to a five-minute fix.
FAQ: how to tile a splashback
How to tile a splashback for beginners?
Start with a flat, clean wall and a level batten. Spread adhesive over a small area, set tiles with spacers, check level every few tiles, then grout after the adhesive cures per the packet. Seal the benchtop edge with silicone, not grout.
How high should a kitchen splashback be?
There is no single height. Many people tile to the underside of the overhead cupboards or just above the cooktop. Check your cooktop’s manufacturer instructions for clearance and any minimum height behind the burners before you buy tiles.
Can you tile over a painted wall?
Often yes, if the paint is sound, clean and keyed. Gloss paint, flaking paint or damp patches need preparation first. Follow the adhesive packet and read our guide to how to tile for the preparation steps.
Can you move a power point for a splashback?
Not yourself. Moving, extending or adding a power point is electrical work that needs a licensed electrician in NSW. Book one before you start tiling so the new position matches the tile layout.
Getting your splashback tiled in Sydney
If you would rather skip the batten, trowel and silicone, we can tile, grout and seal your splashback in one visit and book licensed trades for any power point or cooktop work. Book a handyman in Sydney for the job, then read our guide to replacing a toilet seat for your next small repair.


