DIY tiles are a realistic weekend job for a small splashback, laundry or hallway if you prepare the surface, set out the layout, spread adhesive with the right trowel, and grout once it has cured. The most common failure is tiling onto a surface that is dirty, uneven or unsound, which sends tiles hollow and cracked within months.
This guide covers DIY tiles step by step, including how to tile a wall, a floor and a bathroom wall, how to cut tiles without a tile cutter, how to fix cracked tiles, and what a Sydney handyman charges.
Key points
- DIY tiles suit small, dry areas such as splashbacks and laundries; wet areas need waterproofing by a licensed trade before any tile goes down.
- A long spirit level and the correct notched trowel are the tools you can’t skip, because flat, evenly bedded tiles depend on both.
- Check for asbestos before you remove or drill into old sheeting, tiles or floor coverings in a home built or renovated before 1990.
- A Sydney handyman typically charges about $105 an hour and $140 for a minimum visit (October 2026), and the tiles are usually extra.
DIY tiles: can you do it yourself?
Most people can tile a small dry area with patience and a flat surface. Use this table to check your situation first.
| Your situation | DIY OK? | Why |
|---|---|---|
| Kitchen splashback or laundry wall | Yes | Small wall tiles are forgiving, and you can stop and start without messing up the layout. |
| Hallway or entry floor on a flat slab | Yes, with care | A flat, sound floor makes the job simple, but large tiles show every lippage and high spot. |
| Bathroom or shower walls | Tiles only | The waterproofing layer is licensed work, so book a licensed waterproofer first, then tile over it. |
| Tiling over existing tiles | Check first | It can work, but the old tiles must be sound and flat, as our guide to tiling over tiles explains. |
| Cracked slab or uneven floor | Fix first | Movement in the base cracks new tiles, so repair the base using the concrete crack repair guide. |
| Pre-1990 home with old wet-area linings | Check first | Wet-area linings and floor coverings in older homes may contain asbestos, so identify suspect material before you disturb it. |
| Large job valued above $5,000 | No | Residential building work valued at more than $5,000 must be done by someone licensed by Building Commission NSW. |
DIY tiles: tools and materials
| Item | What it’s for | Tip |
|---|---|---|
| Tiles and spacers | Surface and even joints | Buy extra tiles for cuts and breakages, and keep a few spare for future repairs. |
| Tile adhesive | Bonds the tile to the surface | Choose an adhesive suited to the tile and base. Brands like Mapei and Ardex list the match on the packet. |
| Notched trowel | Spreads an even bed of adhesive | Use the notch size the adhesive and tile packets call for; large tiles need a deeper bed. |
| Spirit level and straightedge | Checks the surface and tile faces | Use a long level, not a short one, because tiny errors compound across the row. |
| Tile cutter or wet saw | Makes straight cuts | A cheap manual cutter handles most ceramic tiles. Porcelain often needs a wet saw. |
| Grout, float and sponge | Fills the joints and cleans the surface | Follow our how to grout tiles guide for the finish. |
| Safety glasses, gloves and dust mask | Protect you from chips and dust | Cutting tiles makes fine dust, so wear a mask suited to it and cut outside. |
How to lay tile: DIY tiles step by step
Work in small sections, and keep the layout symmetrical so the cuts at the edges look deliberate.
- Check the surface is clean, dry, flat and sound, and fix cracks, loose areas and high spots before you start.
- Dry-lay a row of tiles with spacers from the centre of the room or wall, and adjust so edge cuts are at least half a tile.
- Mark a level or square starting line, and use a straight batten as a guide so the first row can’t drift.
- Mix the adhesive to the packet instructions, and spread a thin coat across a small area with the flat edge of the trowel.
- Comb the adhesive with the notched side of the trowel in straight lines, all running in the same direction.
- Press each tile in with a slight twist, set the spacers, and check it with the level across the row.
- Lift the occasional tile to check that the back is fully covered, and adjust your trowel and technique if it isn’t.
- Clean adhesive off the faces and the joints before it dries, and leave the tiles undisturbed for the time on the packet.
- Remove the spacers, grout the joints as the packet describes, wipe off the haze, and seal the grout if the maker recommends it.
How to tile a wall: DIY tiles on walls
Walls are lighter work than floors, but gravity pulls the tiles down while the adhesive sets. Old plaster walls in Sydney terraces often need priming first.
- Fix a straight batten along the bottom row line, because the first row of tiles must sit on something level.
- Strip old paper first if needed, using our guide to removing wallpaper, then prime the wall as the adhesive maker suggests.
- Work from the bottom up in small sections, and check each row against the level before you move on.
- Use spacers on all four sides of each tile, as wall tiles slip down if the adhesive is too thin or wet.
- Leave a small gap at corners and the bench for silicone, and read our skirting board guide for how the floor edge fits.
How to tile a floor: DIY tiles on floors
Floors take weight and movement, so preparation matters more than speed. Plan your exit route before you start.
- Check the slab or substrate for flatness with a long straightedge, and fix any dips or humps before the adhesive goes down.
- Choose floor-rated tiles with a suitable slip rating, and check the packet for wet-area and outdoor use.
- Spread adhesive in small areas and press each tile in firmly, using the trowel notch size the tile packet suggests.
- Check the surface with a straightedge across several tiles, tapping high corners down before the adhesive sets.
- Stay off the floor for the cure time on the packet, and grout only when the adhesive is ready.
How to tile a bathroom wall: DIY tiles in wet areas
Bathroom tiling puts the tiles over a waterproof layer, and that layer is the real protection. Do not skip it.
- Book a licensed waterproofer or plumber, such as TQN Plumber, to waterproof the shower and wet areas before any tile is laid.
- Check the waterproofing has cured as the maker says, then tile over it without drilling or scoring the membrane.
- Use adhesive and grout suited to wet areas, and leave corners and edges for flexible silicone.
- In a pre-1990 home, treat old linings as possible asbestos and check asbestos.nsw.gov.au before you remove or drill them.
- Think about the toilet at the same time, with our guides to replacing a toilet seat and tightening a toilet seat.
How to cut tiles without a tile cutter
You can cut most ceramic tiles without a bench cutter, but porcelain is much harder. Always wear glasses and a mask when you cut.
- Score ceramic tiles with a hand scoring tool along a straightedge in a single firm pass, then snap them over a thin rod.
- Use an angle grinder with a diamond blade outdoors for curves and notches, and wear glasses, gloves and a dust mask.
- Use a tile nipper to nibble small notches around pipes, and take little bites to avoid cracking the whole tile.
- Drill pipe holes with a diamond hole saw, at low speed and with water to keep the bit cool.
- Smooth sharp edges with a rubbing stone, and keep the cut edge against the wall or a trim where it won’t show.
How to fix cracked tiles
A cracked tile is usually a symptom, so find the cause first. Our cracked tile repair guide covers the full method.
- Tap the tile and its neighbours to check for hollow sounds, which suggest the adhesive has failed underneath.
- Check for movement in the floor or wall, because a repair won’t last if the base is still cracking.
- Break up and remove the damaged tile carefully, protecting its neighbours with tape, and clean out the old adhesive.
- Bed the replacement tile in fresh adhesive, press it level with its neighbours and regrout after the adhesive cures.
- Fill hairline cracks in a tile only as a stopgap, because the crack usually keeps growing.
Cost of bathroom tiles and DIY tiles vs hiring a pro
The cost of bathroom tiles depends on the tile, the area and the prep, so get itemised quotes (indicative — get itemised quotes). Labour figures below include GST and come from October 2026 Sydney data.
| Job | Low | Typical | High |
|---|---|---|---|
| Handyman hourly rate, Sydney | $57 | $105 | $140 |
| Call-out or minimum charge, Sydney | $92 | $140 | $170 |
| Half-day handyman, Sydney (4 hours) | $230 | $415 | $645 |
| Full-day handyman, Sydney (8 hours) | $435 | $690 | $1025 |
- Tiles, adhesive, grout and trims are usually extra, so ask whether the quote includes materials and waste removal.
- A small splashback or repair suits the half-day rate, and a full day can cost less than eight hourly-billed hours.
- Larger tiling jobs worth more than $5,000 need a licensed contractor, and work over $20,000 needs a full written contract with Home Building Compensation cover.
Common mistakes to avoid with DIY tiles
- Tiling onto a dirty, uneven or damp surface, so the adhesive fails and the tiles sound hollow within months.
- Skipping the dry-lay, then finding a thin sliver of tile at one edge or a joint that doesn’t line up with the doorway.
- Using the wrong trowel notch or spreading too much adhesive at once, so it skins over before the tile goes on.
- Tiling a shower without licensed waterproofing, or drilling through the membrane after it is done.
- Removing or drilling old wet-area linings in a pre-1990 home without checking for asbestos first.
- Walking on or grouting a floor too soon, instead of waiting for the cure time on the packet.
FAQ: DIY tiles
How to tile a wall for the first time?
Prepare the wall so it is clean, flat and primed. Fix a level batten for the first row, spread adhesive over a small area, and press tiles in with spacers. Work from the bottom up, check each row, then grout once the adhesive has cured.
How to lay tile on a floor?
Check the floor is flat and sound, dry-lay the layout from the centre, then spread adhesive with the correct trowel. Press each tile in with a slight twist, check with a level, and clean off excess adhesive. Stay off it until the packet says it has cured.
How to cut tiles without a tile cutter?
Score ceramic tiles with a hand scorer along a straightedge, then snap them. Use a diamond blade on an angle grinder outdoors for curves, and nippers for notches. Wear glasses, gloves and a dust mask, and note that porcelain is harder to cut by hand.
How to fix cracked tiles?
Find out why the tile cracked first, such as movement or a hollow bed. Remove the tile carefully, clean out the old adhesive, bed a new tile in fresh adhesive and regrout. Hairline cracks filled with a repair kit are only a short-term fix.
Getting tiles laid in Sydney
If you’d rather not tackle DIY tiles yourself, we can repair, replace and regrout tiles in one visit, and point you to a licensed waterproofer for wet areas. Book tiling repairs in Sydney, or if you are updating the bathroom, start with our guide on how to replace a toilet seat.


