How to Fix Chipped Tile: Step-by-Step Guide

How to fix chipped tile: clean the chip, fill it with a colour-matched epoxy or tile repair kit, level it flush, then let it cure before use. The most common failure is filling a chip over dust or soap film, so the prep matters more than the filler.

This guide covers how to fix chipped tile step by step, cracked tile repair, tile chip repair on floors and walls, and how to repair a cracked tile without removing it. If the whole tile needs replacing, our how to tile guide covers the next step.

Key points

  • Small chips and hairline cracks are an eight-step DIY job with a repair kit, a scraper and a clean cloth.
  • The one tool you shouldn’t skip is a proper cleaner for the surface, because soap scum and grease stop epoxy bonding.
  • Check the tile is solid before you fill it: a hollow sound or a crack that travels means the tile needs replacing, not filling.
  • A Sydney handyman typically charges $105 an hour (range $57–$140, October 2026), and small repairs often fit inside the $140 typical minimum charge.

Can you fix a chipped or cracked tile yourself?

Most chips on floor and wall tiles are fine to repair at home, but a few situations need extra care.

Your situationDIY OK?Why
Small chip on a glazed floor or wall tileYesA colour-matched epoxy repair fills the chip and blends in on a stable tile.
Hairline crack on a solid tileYesYou can seal it, but the crack may return if the substrate is moving.
Hollow-sounding or loose tileProbably notTapping gives a hollow sound when the adhesive has failed, so the tile needs relaying.
Cracks running across several tilesGet it checkedThis often points to slab movement; see our concrete crack repair guide.
Shower, bath or other wet-area tilesTake careDon’t cut through or damage a waterproof membrane; a licensed plumber handles waterproofing.
Old tiles in a pre-1990 homeCheck firstHomes built or renovated before 1990 are likely to contain asbestos in wet-area linings and floor coverings; identify suspect material before you disturb it.
RentingAsk firstTell your landlord or agent before you repair tiles, and keep photos of the original damage.

Tools and materials for tile chip repair

ItemWhat it’s forTip
Tile repair kit or two-part epoxyFills chips and hairline cracksPick a colour-matched kit, and follow the manufacturer’s mixing and cure instructions.
Degreaser or methylated spiritsCleans the chipWipe until the cloth comes away clean, then let it dry fully.
Plastic scraper or old credit cardSmooths the filler flushMetal scrapers can scratch the glaze, so keep to plastic.
Masking tapeProtects the surrounding glazeTape right up to the edge of the chip to keep the repair neat.
Fine wet-and-dry paperLevels cured epoxyUse it lightly; too much sanding dulls the glaze around the repair.
Eye protection and glovesProtects you from epoxy and chipsWear a P2 mask if you sand or cut anything cement-based.

How to fix chipped tile: step by step

Allow a dry, well-ventilated room and enough time for the repair to cure before anyone walks or showers on it.

  1. Tap the tile and neighbouring tiles; if they sound hollow or move, stop and plan to replace the tile instead.
  2. Remove loose flakes from the chip with a soft brush and a vacuum, taking care with sharp edges.
  3. Clean the chip and surrounding glaze with degreaser, rinse it, and let it dry completely before you apply any filler.
  4. Mask around the chip with tape, leaving only the damaged area exposed to the filler.
  5. Mix the epoxy or repair compound exactly as the maker states, tinting it to match the tile colour on a scrap first.
  6. Press the filler into the chip with a plastic scraper, slightly overfilling it so you can level it flush once it cures.
  7. Remove the tape before the filler skins over, then leave the repair untouched for the cure time on the label.
  8. Level any raised filler with fine wet-and-dry paper, clean the area, and check the repair with a torch for gaps.

Cracked tile repair: when a crack can be filled

A crack that stays still can be sealed, but a crack that moves will reopen, so check the cause first.

  • Press along the crack and listen for movement or clicks, which show the tile has lost its bond to the substrate.
  • Look for the same crack continuing through grout lines or neighbouring tiles; that points to a structural or slab problem.
  • Use a thin epoxy or crack filler designed for tile and follow the label for pot life and cure.
  • Blend a surface tint or glaze touch-up if the maker supplies it, then let it dry before sealing grout.
  • Replace the tile if it is cracked right through or the crack widens within a few weeks of repair.
  • Check for water entry on bathroom floors, as a cracked tile can let moisture reach the substrate.

Repair cracked tile without removing it

Removing a tile is slow and can damage neighbours, so repair in place whenever the tile is still well bonded.

  • Fill hairline cracks with a clear or tinted epoxy so water can’t creep underneath, then wipe the excess off straight away.
  • Use a tile repair pen or colour kit on surface chips that don’t reach the body of the tile.
  • Re-grout damaged grout lines around the tile; a worn grout line makes a cracked tile look worse and lets moisture in.
  • Apply a sealer to cement-based or unglazed tiles after the repair has cured, as the maker directs.
  • Protect high-traffic floor repairs with a mat or rug until the repair has fully cured.
  • Know when to stop: if more than one or two tiles are damaged, replacing the area may look better than patching.

Tile chip repair on floors, walls and benchtops

Each surface has its own demands: floors take traffic, walls take moisture and benchtops take heat and knocks.

  • On floors, fill the chip slightly proud and sand it flush so shoes and socks don’t catch the edge.
  • On walls, use a thicker mix that won’t slump, and tape the area while it sets.
  • On benchtops, avoid placing hot pans or heavy items on a repair until it has fully cured.
  • Around baths and showers, keep silicone and grout in good order and book a licensed plumber for leaks or waterproofing.
  • If you decide to tile over the damage instead, read whether you can tile over tiles before you buy materials.
  • Near skirting or doors, check trims too; the skirting boards guide shows how to replace damaged ones.

Common mistakes with how to fix chipped tile

  • Filling over dust, soap scum or oil, so the repair peels away within weeks.
  • Mixing the epoxy by eye rather than the exact ratio on the pack, which leaves it soft or brittle.
  • Using a colour that doesn’t match, instead of testing the tint on a scrap and letting it dry.
  • Walking on or wetting the repair before the label’s cure time has passed.
  • Drilling or cutting old tiles and lining in a pre-1990 home without checking for asbestos first.
  • Ignoring a hollow tile or a moving crack, and filling it again and again.

When to call a handyman for a cracked tile (or a licensed trade)

  • Several tiles are cracked or hollow, and the floor may need relaying with a matched replacement.
  • The tiles are in a shower, bath surround or wet area where waterproofing could be damaged.
  • The cracks follow a straight line across the slab, which can signal movement that needs an engineer.
  • Your home was built or renovated before 1990, and the tiles or adhesive may contain asbestos.
  • Water is coming through or the substrate feels damp, which needs a licensed plumber to trace a leak.
  • You want the repair invisible, or you’re renting and need the work done neatly and documented.

Cost to hire a handyman to fix a chipped or cracked tile in Sydney

Prices below include GST and come from October 2026 Sydney metro data. Our toilet seat tightening guide is a good bundle job.

JobLowTypicalHigh
Handyman hourly rate, Sydney$57$105$140
Call-out or minimum charge, Sydney$92$140$170
Weatherproofing or caulking (silicone and sealing), Sydney$115$205$345
Minor plastering or patching, Sydney$140$230$575
Half-day handyman, Sydney (4 hours)$230$415$645
  • Replacing a tile costs more than filling one because of matching, removal and regrouting.
  • Spare tiles from the original job cut the cost, so keep leftover tiles from renovations.
  • Bundle other small jobs, like removing wallpaper described in our wallpaper removal guide, into the same visit.

FAQ: how to fix chipped tile

How do you fix a chipped tile?

Clean and dry the chip, mask the edges, fill it with colour-matched epoxy, level it flush and let it cure as the label says. Check the tile is solid first, because a hollow tile needs replacing rather than filling.

Can you repair a cracked tile without removing it?

Yes, if the tile is still well bonded. Fill hairline cracks with thin epoxy, tint and seal them, and regrout any damaged lines around the tile. If the crack keeps reopening, the tile or substrate is moving.

Is tile chip repair a long-term fix?

A good repair on a stable tile can last for years, especially in low-traffic areas. In showers or high-traffic floors it may wear sooner. Follow the maker’s cure time, and avoid harsh cleaners that attack epoxy.

Do I need a licensed tradesperson to fix a cracked tile?

Not for a cosmetic repair, but waterproofing, plumbing and electrical work always need a licence in NSW. If tiles sit over a shower membrane or the home predates 1990, check for asbestos and speak to a licensed trade first.

Getting a cracked tile repaired in Sydney

If you’d rather not match colours and wait on cure times, we can repair or replace the tile, regrout the edges and flag any leaks that need a licensed plumber. Book tile repair in Sydney and add other small jobs, such as those in our toilet seat replacement guide, to the same booking.