Concrete Crack Repair: Causes, Fixes & Costs

Concrete crack repair is a clean, fill and seal job: widen the crack slightly, remove loose material, fill it with a repair product matched to the crack type, then seal the surface. The biggest thing that goes wrong is treating a moving or structural crack as a cosmetic one, so check why it cracked before you fill it.

This guide covers concrete crack repair step by step, how to fix cracks in concrete paths and driveways, which concrete repair products suit which cracks, and what a Sydney handyman charges. If you tile over the slab afterwards, see our how to tile guide.

Key points

  • Most hairline and shrinkage cracks are DIY jobs of about eight steps with a wire brush, a vacuum and a flexible or rigid filler.
  • Wear eye protection and a P2 respirator when grinding or chiselling, because concrete dust contains fine silica.
  • Cracks that keep growing, step up or run through walls and footings need a structural engineer or licensed builder, not a filler.
  • A Sydney handyman typically charges $105 an hour for repairs (range $57–$140, October 2026), with minor patching about $230 per job.

Can you do concrete crack repair yourself?

Most surface cracks in paths, patios and garage floors are fine to repair, but some cracks are warning signs.

Your situationDIY OK?Why
Hairline shrinkage crack in a path or patioYesA cosmetic crack that is not moving can be sealed with a flexible filler or a repair product.
Cracked concrete repair in a drivewayYes, with prepA clean, dry crack and the right filler for traffic loads gives a durable fix; see our concrete driveway cost guide for resurfacing.
Crack that is wider at one end or has steppedGet it checkedOne side sitting higher than the other suggests movement or soil problems that filler will not fix.
Cracks in a footing, retaining wall or house slabNoThese can be structural, so ask a structural engineer or licensed builder before repairing.
Cracks with water coming throughCheck firstWater means drainage or waterproofing problems; book a licensed plumber for pipes and waterproofing.
Slab near old fibro or pre-1990 coatingsCheck firstHomes built or renovated before 1990 are likely to contain asbestos; identify suspect material before you disturb it.
Rented propertyAsk firstTell the landlord or agent; cracks may be their responsibility, and consent is needed for repairs.

Concrete repair products: which one for which crack

Product typeBest forWatch out for
Flexible polyurethane or sealant (Sika, Selleys, Bostik)Hairline cracks and joints that move a littleNeeds a clean, dry crack and a backing rod in wider gaps; follow the label for cure and recoat times.
Cement-based crack filler or repair mortarWider cracks and spalled edges in paths and drivewaysDampen the edges as directed, and cure it slowly so it doesn’t shrink or crack again.
Epoxy injection kitStructural-looking cracks, once an engineer has approved the methodNot a DIY fix for a moving crack; follow the manufacturer’s instructions strictly.
Concrete patch or resurfacerSpalled areas and shallow surface damageEdges must be cut square, and the base needs primer if the label asks for it.
Self-levelling compoundLow spots inside the homeNot suited to outdoor slabs; check the maker’s instructions.

Concrete crack repair: step by step

Allow a dry day with no rain forecast, and keep a helper nearby if you are working on a driveway.

  1. Inspect the crack and measure how wide it is at several points; if it is growing or stepped, stop and ask an engineer.
  2. Put on gloves, eye protection and a P2 respirator, then widen the crack slightly with a chisel or grinder so the filler has something to grip.
  3. Remove loose concrete and dust with a wire brush and a vacuum, then blow the crack clean so no dust stops the bond.
  4. Mask the edges with tape to keep the surface clean, and place a backing rod in deeper cracks if the label says to.
  5. Fill the crack with the repair product you’ve chosen, pressing it in with a trowel or caulking gun and following the manufacturer’s instructions.
  6. Tool the surface flat, remove the tape while the product is wet, and keep the repair out of the rain until it has cured as the label says.
  7. Seal the surface if the maker recommends it, once the repair is cured, to reduce water getting in.
  8. Wash tools straight away, check the repair after the first storm, and monitor the crack for movement over the following weeks.

How to fix cracks in concrete driveways

Driveways cop traffic, tree roots and weather, so the repair has to cope with movement and weight.

  • Clean oil and grease with a degreaser first, because filler won’t stick to oily concrete.
  • Use a product labelled for vehicle traffic, and keep cars off until the label says it is safe.
  • Check for tree roots lifting the slab, and ask an arborist or builder before you patch over the cause.
  • Fill cracks along control joints with a flexible sealant, not a rigid mortar that will crack again.
  • Pressure wash the driveway first, then let it dry fully before you fill, since damp concrete stops most repair products bonding.
  • Consider resurfacing or a new slab if many cracks appear, and compare quotes from licensed concreters.

Repairing cracked concrete floors, patios and steps

Indoors and under cover, the main risks are dust and flooring bond, not rain and traffic.

  • Vacuum with a HEPA-style vacuum if you grind a crack inside, since concrete dust spreads far.
  • Test for moisture before you cover a repaired slab with tiles or flooring, because damp slabs lift adhesive.
  • Level low spots with a compound made for the job, and read our guide on whether you can tile over tiles before you cover old surfaces.
  • Repair cracked steps with a repair mortar and avoid thin feathered edges that crumble.
  • Keep a small gap or flexible joint where the slab meets walls, so seasonal movement doesn’t crack the repair.
  • Fix skirting and trims after the repair has cured; see the skirting boards guide if you need to replace them.

Common mistakes with concrete crack repair

  • Filling a crack without cleaning dust and loose pieces out, which leaves the product with nothing to bond to.
  • Using rigid mortar in a crack that still moves, so it cracks again within a season.
  • Ignoring wider or stepped cracks that point to soil movement, drainage or tree-root damage.
  • Skipping eye protection and a respirator while grinding, and breathing silica dust.
  • Repairing in wet or very hot weather, then not curing or protecting the repair.
  • Sanding or chiselling old coatings or sheeting in a pre-1990 home without checking for asbestos.

When to call a handyman for concrete crack repair (or a licensed trade)

  • The crack is long, deep or repeated across several slabs, and you’re unsure whether it’s cosmetic or structural.
  • One side of the crack sits higher than the other, or the crack runs up a wall or through a footing.
  • You suspect asbestos in adjoining sheeting, render or coatings; treat it as asbestos and get it identified before work starts.
  • Water or a leaking pipe is involved, which needs a licensed plumber for repairs and waterproofing.
  • The job would grow beyond $5,000 of residential building work, which must be done by someone licensed by Building Commission NSW.
  • You’re renting or in a strata building and want the repair done neatly, with the right approvals.

Cost to hire a handyman for concrete crack repair in Sydney

Prices below include GST and come from October 2026 Sydney metro data. Our cracked tile repair guide covers the matching tile fixes.

JobLowTypicalHigh
Minor plastering or patching, Sydney$140$230$575
Weatherproofing or caulking (sealing), Sydney$115$205$345
Handyman hourly rate, Sydney$57$105$140
Call-out or minimum charge, Sydney$92$140$170
Half-day handyman, Sydney (4 hours)$230$415$645
  • Patching has a wide range because crack length, depth, access and surface prep all change the time.
  • Repair products are usually extra, so ask whether the quote includes the filler, sealer and disposal.
  • Bundle several small jobs into one visit, such as tightening a toilet seat, so you pay the minimum charge once.

FAQ: concrete crack repair

How do you fix cracks in concrete?

Clean the crack, remove loose material, widen it slightly if needed, and fill it with a repair product suited to the crack type. Tool it flat, protect it while it cures, then seal the surface. Always follow the product’s label for cure and recoat times.

How do you repair concrete cracks that keep coming back?

A returning crack is usually moving, so use a flexible sealant rather than rigid mortar. If it widens, steps or runs through walls, stop and ask a structural engineer or licensed builder to look at the cause before you fill it again.

Is cracked concrete repair worth doing on a driveway?

Yes for narrow, stable cracks, because sealing keeps water out and slows further damage. Wide, widespread or sinking cracks may mean resurfacing or replacing the slab. Get itemised quotes and compare repair with resurfacing before you commit.

Which concrete repair products are best?

It depends on the crack. Flexible sealants suit hairline and moving cracks, cement-based mortar suits wider cracks and chipped edges, and epoxy injection suits structural repairs approved by an engineer. Always follow the manufacturer’s instructions for preparation and cure times.

Getting concrete crack repair done in Sydney

If you’d rather not grind and fill yourself, we can clean, repair and seal the crack in a single visit, and we’ll tell you honestly when a crack needs an engineer. Book concrete crack repair in Sydney and add other small jobs, like those in our toilet seat replacement guide, to the same booking.